Abstract:Indium antimonide (InSb) is a III-V compound semiconductor with a narrow bandgap and a high electron mobility, and is used in various optoelectronic devices. Electrodeposition represents a low-cost, scalable method for fabricating InSb films. In the literature, aqueous electrolytes and ionic liquids have commonly been applied. In this work, the electrodeposition of InSb films and nanowires from a dimethyl sulfoxide (DMSO)-based electrolyte was demonstrated. This electrolyte enabled electrodeposition in a broader potential range and at higher temperatures as compared to aqueous electrolytes. The electrolyte has a lower viscosity than ionic liquids, therefore exhibiting better mass transport properties for electrodeposition. It was shown that antimony(III) chloride, a precursor that is commonly used for InSb electrodeposition, leads to the formation of the metastable "explosive" antimony allotrope. Instead, self-prepared antimony(III) nitrate and indium(III) methanesulfonate were used, and were proven to be suitable precursors. Electrolytes with a 5:1 indium-to-antimony precursor molar ratio enabled electrodeposition of InSb films at 21 °C and 120 °C on platinum and n-type InSb(400), as well as electrodeposition of InSb nanowires in anodized aluminum oxide templates. The morphology, elemental composition and crystallinity of as-deposited InSb was analyzed using scanning electron microscopy (SEM), energy-dispersive X-ray spectroscopy (EDX) and X-ray diffraction (XRD), respectively. It was demonstrated that the film quality did not improve at 120 °C. Tauc plots from FT-IR transmission measurements were used for the determination of the bandgap of the deposits. The bandgap of the InSb films on platinum was 0.159 eV at 21 °C and 0.168 eV at 120 °C, whereas the bandgap of the InSb film deposited at 120 °C on InSb(400) was 0.186 eV.

Potassium Borohydride Reducing Route to Phase-Pure Nanocrystalline InSb at Low Temperature

Straight Indium Antimonide Nanowires with Twinning Superlattices Via a Solution Route.

Solvothermal Coordination–Reduction Route to γ-NiSb Nanocrystals at Low Temperature

Synthesis of NIR/SWIR Absorbing InSb Nanocrystals Using Indium(I) Halide and Aminostibine Precursors

ChemInform Abstract: Organothermal Synthesis and Characterization of Nanocrystalline Β‐indium Sulfide.

A low-temperature route to InP nanocrystals

Low-Temperature Synthesis of Nains2 Nanoplate Layered Structure by One-Step Solvothermal Decomposition of In(S2cnet2)(3) Complex

Synthesis and characterization of nanocrystalline NiSb and NiSb2 at low temperature

Anisotropic Growth of Indium Antimonide Nanostructures

Preparation And Characterization Of Bismuth Sulfide Single Crystal Nanorods In Ionic Liquids

Synthesis of Mn-Doped Indium Antimonide Nanowires by Multi-Step Depositions and Annealing

Electrodeposition of indium antimonide (InSb) from dimethyl sulfoxide-based electrolytes

Hydrothermal Preparation and Characterization of Nanocrystalline Powder of β-Indium Sulfide

Ni3InSb: Synthesis, Crystal Structure, Electronic Structure, and Magnetic Properties

Synthesis and Characterization of Ternary CuInS2 Nanorods Via a Hydrothermal Route

Solid State Synthesis At Intermediate Temperature And Structural Characterization Of Kinse2

A novel method for the preparation of III-V semiconductors: sonochemical synthesis of InP nanocrystals.

Microstructure and thermoelectric properties of InSb compound with nonsoluble NiSb in situ precipitates

ChemInform Abstract: A Safe Low Temperature Route to InAs Nanofibers.

Free-Standing Two-Dimensional Single-Crystalline InSb Nanosheets.