Abstract:BACKGROUND: Cardiovascular stents and some materials contacted with blood have been developing rapidly. However, there is not a uniform method to evaluate the thrombosis of biomaterials at present. OBJECTIVE: To observe the relationship between the concentration of fibrinogen and thrombosis, and establish a new method for evaluating the thrombus formation on biomaterials in vitro. DESIGN, TIME AND SETTING: A control observational experiment of material science was performed in the Testing Center for Medical Device of National Institute for the Control of Pharmaceutical and Biological Product from December 2007 to July 2008. MATERIALS: One healthy Japanese rabbit, clean grade and weighing 2.5 kg, was used in the experiment. Glass was the product of Yancheng Rongkang Glassware CO., LTD.. Medical silicone rubber and polyethylene were the products of Tianjin plastic research institute. METHODS: Blood samples were drawn from the heart of rabbit with 3.8% sodium citrate for partial anticoagulation. Then, a part of sodium citrate was added into the partial anticoagulation blood for complete anticoagulation every 3 minutes. The concentration of fibrinogen was measured in plasma after separation. The blood samples of partial anticoagulation obtained with the same method as above were divided into four groups: positive, silicone rubber, polyethylene and negative groups. In the positive, silicone rubber, polyethylene groups, the blood samples of partial anticoagulation were contracted with glass, silicone rubber and polyethylene, respectively. The blood samples in the negative group were not contracted with anything. Fifteen minutes later, the sodium citrate was added in the four groups for complete anticoagulation. The concentration of fibrinogen was measured in plasma after separation. MAIN OUTCOME MEASURES: The relationship between concentration of fibrinogen and thrombosis were observed. And the extents of thrombus formation in the positive, silicone rubber, polyethylene groups were compared. RESULTS: With the increase of exposure time of the partial anticoagulation blood in vitro, the amount of thrombus formation increased gradually. The later the anticoagulant was added, the lower the concentration of fibrinogen was. The results suggested that the concentration of fibrinogen was inversely proportional to the amount of thrombosis. The concentrations of fibrinogen in the negative, silicone rubber, polyethylene groups were significantly higher than that in the positive group (t =2.842-3.737, P < 0.05). There was no significant difference in concentrations of fibrinogen between the silicone rubber and polyethylene groups (t=0.747, P > 0.05), but the concentrations of fibrinogen in both of them were significantly lower than that in the negative group (t =3.691, 3.192, P < 0.05). CONCLUSION: The measurement of fibrinogen concentrations can be used as a screen test for evaluation of thrombus formation on biomaterials, which is proved by glass, polyethylene and silicone rubber. The findings show that the blood compatibility of silicone rubber and polyethylene is better than glass.

The Application Study on Platelet Adhesive Test in vitro in Medical Devices Evaluation

[In Vitro Evaluation of the Function of Sheet Biomaterials in Platelet Activation].

A microfluidic hemostatic diagnostics platform: Harnessing coagulation-induced adaptive-bubble behavioral perception

STUDY ON WASHING METHOD OF MEDICAL APPARATUS AND INSTRUMENT

[In-Vitro Evaluation of Haemocompatibility of Biomaterials].

Improved Method for the ASTM Platelet and Leukocyte Assay: Use of Minimal Heparinization in a Screening Test for Hemocompatibility of Blood-Contacting Medical Devices

Molecular Biomarkers for In Vitro Thrombogenicity Assessment of Medical Device Materials

Laboratory investigation of platelet function and its application

Quantification of adherent platelets on polymer-based biomaterials. Comparison of colorimetric and microscopic assessment

Biocompatibility, Biodegradation, and Neovascularization of Human Single-Unit Platelet-Rich Fibrin Glue: an in Vivo Analysis.

In vitro Evaluation of the Microstructural Vascular Scaffold with Micro-Tip Direct Writing Technology

A new method for evaluating the thrombus formation on biomaterials in vitro

Biocompatibility and haemostatic effect investigation of a newly developed biodegradable biopaper with haemostatic and anti-adhesive activity

Platelet function tests: a comparative review

PC Technology Improving the Hemocompatibility of Polymer Membranes Developed for Biomedical Application

[Study and Evaluation on Hemocompatibility of Biomaterials].

In vitro hemocompatibility screening of a slippery liquid impregnated surface coating for extracorporeal organ support applications

A Novel Method for Evaluating Compatibility of Hepatocytes with Some Kinds of Biomaterials

Antiplatelet Agents Inhibit Platelet Adhesion and Aggregation on Glass Surface Under Physiological Flow Conditions: Toward a Microfluidic Platelet Functional Assay Without Additional Adhesion Protein Modification

Platelet Function Tests: A Review of Progresses in Clinical Application

Hemocompatibility Evaluation of Small-Caliber Expanded Polytetrafluoroethylene Vessel with Heparin Collagen Layer-by-layer Assembly Multilayer