Abstract:Many studies have been carried out on the phosphating of steel and aluminum alloys used in automotive engineering, but characterization of the properties of the phosphate layers formed by the co-phosphating of these alloys in the presence of different base metals is still lacking. In this study, the crystal structure and properties of the phosphate conversion layers formed on the surface of the aluminum alloys important in vehicle manufacturing (cast and forged AlSi1MgMn, and AA6014 panel) and the CRS SAE 1008/1010 reference steel plate by co-deposition prior to painting were investigated. On a process line set up for the phosphating of typical iron and steel alloys, the phosphate coating was formed using nitrite and nitroguanidine accelerators under identical technological parameters. The microstructure of the formed phosphate layers was examined using scanning electron microscopy (SEM), its phase composition using X-ray diffraction (XRD), and its elemental composition using energy-dispersive X-ray analysis (EDX). The suggested main crystalline phase (Zn2.3(Ni0.1Mn0.6)(PO4)2·4H2O) in the surface phosphate layer of both aluminum alloys studied was similar to hopeite, whereas in the steel plate, a minor hopeite phase were identified in addition to the main crystalline phosphophyllite phase (~95%). It can be concluded that, during the combined phosphating treatments, the surfaces of different aluminum and steel alloys behaved similarly to the individual treatments and did not impede the coating reactions of the other metal. To obtain an adequate coating of aluminum and steel alloys, fluoride should always be present in the production line. Comparing the effects of accelerators, we found that the use of nitrite accelerator with the same amount of fluoride resulted in a higher coverage and better quality of the surface protective layer of the aluminum alloys. However, for the steel plate, there was no significant difference between the phosphate coatings prepared with the two different accelerators.

Zinc Phosphate Coating on the Surface of AZ91D Mg Alloy

A Study and Application of Zinc Phosphate Coating on Az91d Magnesium Alloy

Growth of Zinc Phosphate Coatings on AZ91D Magnesium Alloy

Zinc phosphate film and cathodic electro-coat deposition on magnesium alloy

Electroless Ni–P deposition plus zinc phosphate coating on AZ91D magnesium alloy

Structure and Formation Mechanism of Phosphate Conversion Coating on Die-Cast Az91d Magnesium Alloy

Influence of sodium metanitrobenzene sulphonate on structures and surface morphologies of phosphate coating on AZ91D

Structures of Zinc-Manganese Phosphate Film and Organic Coating on Magnesium Alloys

Nano ZnO-assisted formation of zinc phosphate conversion coating for improving corrosion protection of AZ91D magnesium alloy

Preparation and properties of nano ZrO2 coating on magnesium alloy

Coating Pretreatment for Mg Alloy AZ91D

The Study of a Phosphate Conversion Coating on Magnesium Alloy AZ91D: III. Nano-particle Modification

Preparation of Conductive and Corrosion Resistant Phosphate Conversion Coating on AZ91D Magnesium Alloy

Ni-P deposits and non-chromate pretreatment technology on magnesium alloy

Phosphate Process and Performance of Zinc Phosphate Coating on AZ31B Magnesium Alloy

Effect of zinc–phosphate–molybdate conversion precoating on performance of cathode epoxy electrocoat on AZ91D alloy

Influence of pH of Phosphating Bath on the Zinc Phosphate Coating on AZ91D Magnesium Alloy

Phytic acid conversion coating on AZ31B magnesium alloy

Grain Refinement Promotes the Formation of Phosphate Conversion Coating on Mg Alloy AZ91D with High Corrosion Resistance and Low Electrical Contact Resistance

Crystal Structure and Properties of Zinc Phosphate Layers on Aluminum and Steel Alloy Surfaces

Tuning the nucleation kinetics of phosphate chemical conversion coating on Mg-Gd-Y-Zr magnesium alloy: The effect of pretreatment and organic additive