Abstract:The morphology of TiC is not difficult to control when the titanium matrix composites with high TiC content are prepared by the melting-casting method. TiC tends to grow into dendrites, increasing the brittleness of the Ti matrix composites. In this study, in-situ TiC-reinforced titanium matrix composites with varying Nb content were prepared by adding Nb. The effects of adding Nb on the microstructure evolution and mechanical properties of the composites were studied. The results show that with the increase of Nb content, the grain size of the composites decreased gradually from 276 μm to 122.8 μm, the primary TiC content decreased, and the eutectic TiC content increased. On the other hand, the orientation relationship between TiC (111)//β-Ti (110) and TiC [10 1 ‾ ]//β-Ti [ 1 ‾ 11] was studied by HTEM. The two-dimensional mismatch of TiC (111)//β-Ti (110) is only 9.06 %, which means that TiC can be used as a nucleation particle of β-Ti. Furthermore, there was a gradual increase in the Rockwell hardness of the composites as the Nb content was incrementally raised from 0 wt% to 1.5 wt%, with the highest recorded value being 47.4 HRC. Notably, when the Nb addition reached 1.0 wt%, the composite achieved its maximum tensile strength of 1352.9 MPa, signifying a 69 % enhancement compared to the absence of Nb. This is due to the combined effect of fine grain strengthening, solution strengthening, and second-phase strengthening in the composites. It introduces a novel approach to regulate the in-situ formation of TiC morphology during the preparation of titanium matrix composites through melting and casting.

Microstructure and mechanical properties of as-cast Ti-N alloy

Microstructure and Mechanical Properties of As-Cast Ti-N Alloy

Microstructure and mechanical properties of in-situ nitride-reinforced refractory high-entropy alloy TiZrHfNbTa matrix composites

Microstructure and Mechanical Properties of the TiN Particles Reinforced IN718C Composite

Effect of N Content on Microsegregation, Microstructure and Mechanical Property of Cast Ni-Base Superalloy K417g

Study on the Preparation of Network Ti-N/Ti Composites by Nitridation of Ti Powders

Fabrication and mechanical properties of Ti2AlN/TiAl composite with continuous network structure

Microstructure, mechanical properties and strengthening mechanism of in-situ synthesized TiC/6061 nanocomposites

Microstructural Characteristics and Evolution of Ti2AlN/TiAl Composites with a Network Reinforcement Architecture During Reaction Hot Pressing Process

Microstructure and Compressive Properties Ofin SituSynthesized TiC/Ti Composites

Microstructure Evolution and Tensile Properties of Conventional Cast TiAl-based Alloy with Trace Ni Addition

Effect of Nb addition on microstructure and mechanical properties of TiC/Ti-7.8Cr composites

In-situ laser additive manufacturing of Ti6Al4V matrix composites by gas–liquid reaction in dilute nitrogen gas atmospheres

Microstructure elaboration and mechanical properties of AlN_p/4032Al composite

The microstructural evolution and enhanced mechanical properties of in-situ Ti(C, N)-reinforced CoCrFeNiTi high-entropy alloy composites fabricated via mechanical alloying and spark plasma sintering

Microstructure and Mechanical Properties of an Al–Ni–Co Intermetallics Reinforced Al Matrix Composite

Microstructure and mechanical properties of particulate reinforced matrix composite

Microstructure and Mechanical Properties of Nb-Si Alloy with Addition of Mn

Microstructure and compressive properties of in situ synthesized (TiB + TiC)/Ti composites

Microstructure and compression behavior of in-situ synthesized Ti2AlC reinforced Ti-48Al-2Cr alloy with carbon nanotubes addition

An Investigation of Microstructural Evolution, Tensile Properties and Work-Hardening Behavior of Nanosized TiB2/Al-Cu-Mn Composites