Abstract:Hollow fiber membranes fabricated via dry/wet phase inversion method usually have two dense skin layers,which will increase its resistance of mass transport as a support membrane. It is necessary that the dense skin layer of support membrane has been eliminated to improve separation performance of composite membrane. The excellent. chemical resistance of poly(vinylidene fluoride) (PVDF) to many acids and alkalis has made it as an attractive membrane material, and then it's often fabricated as porous hollow fiber membrane by phase inversion. In the process, the formation of the skin layer is due to the rapid exchange between solvent and coagulation, so many attempts have been made to slow it, so as to control the formation of the skin layer. In this paper, it has been found that the fabrication progress becomes unstable, and the membrane prepared has noncircular lumen, when the "weak" or "soft" coagulation is used. To increase the fabrication solution stability during membrane formation, dope viscosity was focused in this experiment. Dimethyl acetamide (DMAc) was used as solvent as well as internal coagulant, and the additives including LiCl, water and surfactant Span were chosen to investigate their effect oil the viscosity of the fabrication solution. The dope viscosity will greatly increase after adding LiCl, while the variety of dope viscosity is unconcerned in the fabrication solution concentration as adding water. The homogenization and stability of the fabrication solution are improved by adding Span,and the viscosity increases at the same time. Without increasing PVDF concentration, the stability of the nascent membrane was improved by increasing the fabrication viscosity. The PVDF hollow fiber membrane with the structure of single outer skin layer and finger-like pore through the cross-section, has been successfully fabricated. The mean pore radius and water flux of the single skin hollow fiber membrane were greatly improved.

Morphology control of asymmetric membranes by UV irradiation on polyimide dope solution

Polymorphism in Porous Poly(vinylidene Fluoride) Membranes Formed Via Immersion Precipitation Process

Fabrication of Hydrophilic and Sponge-Like PVDF/brush-like Copolymer Blend Membranes Using Triethylphosphate As Solvent

Controlling the Morphology and Crystal Form of Symmetric Network PVDF Membranes by Bath Temperature

Morphology and Formation Mechanism of Poly(Vinylidene Fluoride) Membranes Prepared with Immerse Precipitation: Effect of Dissolving Temperature

Effect of Dissolving Temperature of Dopes on the Morphology of PVDF Membrane

Effect of gelation medium on gelation rate and cross-sectional morphology of polyimide membrane

Modulation the Morphologies and Performance of Polyacrylonitrile-Based Asymmetric Membranes Containing Reactive Groups: Effect of Non-Solvents in the Dope Solution

Membrane Structure Control of BTDA-TDI/MDI (P84) Co-Polyimide Asymmetric Membranes by Wet-Phase Inversion Process

Influence of Dope Viscosity on the Fabrication of Pvdf Hollow Fiber Membranes with Single Skin Layer

Photochemical control of microphase structure in biocompatible polyester membranes generated by ultraviolet irradiation

Thermo-sensitive ionic microgels via post quaternization cross-linking: fabrication, property, and potential application

Performance Control of Asymmetric Poly(phthalazinone Ether Sulfone Ketone) Ultrafiltration Membrane Using Gelation

Preparation Of Thermally Imidized Polyimide Nanofiltration Membranes With Macrovoid-Free Structures

Formation of Macrovoid-Free PMDA-MDA Polyimide Membranes Using a Gelation/Non-Solvent-Induced Phase Separation Method for Organic Solvent Nanofiltration

Microstructure Manipulation in PVDF/styrene-maleic Anhydride Copolymer Composite Membranes: Effects of Miscibility on the Phase Separation

Experimental Study of the Control of Pore Sizes of Porous Membranes Applying Chemicals Methods

Finely tuning the microporosity in dual thermally crosslinked polyimide membranes for plasticization resistance gas separations

Effects of Coagulant Ph and Ion Strength on the Dehydration and Self-Assembly of Poly(N, N-Dimethylamino-2-Ethyl Methacrylate) Chains in the Preparation of Stimuli-Responsive Polyethersulfone Blend Membranes

Diverse Morphologies of PVDF Hollow Fiber Membranes and Their Performance Analysis As Gas/liquid Contactors

Constructing Lamellar Micromorphology in Fluorinated, Block Anion Exchange Membranes from Photocontrolled Raft Polymerization