Study on Preparation Technology of Al2O3 Ceramics

王峰,李惠琪,李敏,冯婷

2008-01-01

Abstract:The technical status and the deficiencies of the alumina ceramic material preparation are summarized. The new technology of preparing alumina ceramic by plasma jet melting method is proposed for the first time.The characters of the technology are introduced,and the trend of its development is forecasted.

What problem does this paper attempt to address?

Progress in Preparation of Nanocrystalline Alumina Ceramics

何佳,李芳

DOI: https://doi.org/10.3969/j.issn.1009-444x.2008.03.005

2008-01-01

Abstract:The techniques of preparing nanocrystalline alumina powders were reviewed.The methods mainly include sol-gel,precipitation,microemulsion,and detonation.The advanced sintering techniques such as hot-pressed sintering,microwave sintering and spark plasma sintering were also described.Comparing with the conventional ones,nanocrystalline alumina ceramics using these new sintering techniques exhibit more superior properties.
Recent Progress of High Purity Al2O3 Ceramic

董亚丽,许富民,石小磊,谭毅

DOI: https://doi.org/10.3969/j.issn.1673-9981.2009.02.004

2009-01-01

Abstract:The paper reviewed the major research progress in the processing of Al2O3 powder,the sintering assistants and sintering methods of high purity Al2O3.Meanwhile,some view points of further development of alumina ceramics are proposed.
Application of Plasma Technique in the Development of Ceramic Material

颜鲁婷,司文捷,苗赫濯

DOI: https://doi.org/10.3969/j.issn.1673-2812.2003.01.027

2003-01-01

Materials Science and Engineering

Abstract:The applications of plasma technique in the development of ceramic materials including hot-plasma coating,cold-plasma surface modification,plasma synthesizing ultrafine powder,plasma sintering and plasma analyzing were introduced in detail.The future of plasma in the development of ceramic materials was also viewed.
Preparation of Al2O3 Ceramic Coating by Electrolytic Plasma Processing and Its Properties

WC Gu,DJ Shen,YL Wang,GL Chen,WR Feng,GL Zhang,CZ Liu,SZ Yang

DOI: https://doi.org/10.7498/aps.54.3263

IF: 0.906

2005-01-01

Acta Physica Sinica

Abstract:Metallurgically bonded Al2O3 ceramic coating was prepared on steel surface with the combined method of arc spraying and electrolytic plasma processing. The composition and microstructure of the ceramic coating were analyzed by x-ray dif fraction, scanning electron microscony and EDS. The corrosion resistance and wea r resistance of the ceramic coating were measured. The results show that the cer amic coating is compact and mainly composed of α-Al2O3, γ-Al2O3, θ-Al2O3 and a little of a morphous phase. The duplex coating shows favorable corrosion resistance and wear resistance properties.
Research on the Organization of Ceramic Coating by Plasma Spraying

马韶霞,孙宏飞,燕友增,高歌

DOI: https://doi.org/10.3969/j.issn.1673-5587.2010.02.003

2010-01-01

Abstract:In order to meet the surface requirements of the strengthened surface metallurgy parts,this paper mainly studied microstructure,hardness and friction and wear of the plasma-sprayed ceramic coating of Al2O3-13wt% TiO2.The results show that Al2O3-13% TiO2 coating has a good bond strength and density. Combination of strength is low relatively; and the hardness is larger; However,because of more containing ceramics,thermal shock resistance is slightly worse.
Preparation and Characterization of Al-Al2O3 Metal Ceramics Via Powder Metallurgy Methods

Da Ming Du,Rui Hua Wang,Jie Guang Song,Si Yuan Yu,Yao Qi Li,Ning Liu,Gui Lian Cao,Shuang Dong,Gang Chang Ji

DOI: https://doi.org/10.4028/www.scientific.net/kem.697.350

2016-01-01

Key Engineering Materials

Abstract:Metal ceramics are a important new engineering materials with the advantages of ceramics and metal materials. The Al-Al2O3 metal ceramics were prepared via the powder metallurgy methods and characterized in this paper, which lay the base for preparing the high performance cermet materials. Through the results and analysis, the conclusions are shown that the relative density is increased with a increasing forming pressure, the electrical resistivity is decreased with a increasing forming pressure. The relative density is increased with a increasing sintering temperature under 700°C, the relative density decreases with a increasing sintering temperature above 700°C, the electrical resistivity is shown the opposite tendency. Through the optimizing the technological parameter, such as the sintering temperature at 700°C, the forming pressure under 20MPa, the Al content for 75wt%, Al-Al2O3 metal ceramics are successfully prepared with the high relative density and the low electrical resistivity, the relative density is 97.52%, and the electrical resistivity is 101.34Ω·m
Preparation and Characterization of Nanoporous Alumina As Ceramic Membrane Materials

Zongyuan Li,Wei Pan

DOI: https://doi.org/10.1088/1757-899x/678/1/012031

2019-01-01

IOP Conference Series Materials Science and Engineering

Abstract:Abstract To meet growing electricity demand and greenhouse gas emission limitation in the future, it is urgency to improve existing power plant more efficientand less CO2 emission. Oxygen combustion instead of air combustion is quite good to raise up the fossil fuels efficiency. And separation oxygen from the air by ionic conductance at high temperatures is promising in large fuel power plants. Ionic separation processes by ceramic dense membrane need a good support porous membranes with good mechanical and permeable property. Present research reports the porous alumina with nanoporous structure was prepared by vacuum filtration and rapid sintering as a kind of porous support layer in the oxygen ceramic separation membrane. The microstructure of nanoporous alumina was analysed, the mechanical properties and gas permeability were tested and compared with some conventional pore-former method made porous ceramics. The uniform nanopores alumina ceramics with both high strength and high permeability achieved by a vacuum filtrate and rapid sintering method is a candidate as the porous support application in fuel cell and gas separation field.
Ceramic Thin Coating Prepared by Micro-plasma Oxidation

蔡宗英,张莉霞,邢献然,李运刚

DOI: https://doi.org/10.3969/j.issn.1009-2617.2004.03.003

2004-01-01

Abstract:Micro-plasma oxidation is a new preparation technology of thin ceramic coating on the surface of some non-ferrous. The ceramic coatings possess some excellent capability of corrosion resistance, heat-strike resistance, wearlessness, electric insulation and so on. The development history of (micro)-arc oxidation technology, the process and the principle for growth ceramic coating, and coating properties of micro-arc oxidation were simply described in this paper, which pointed that the micro-arc oxidation was a new technology and have a bright prospect in application.
Preparation and Application Progress of Porous Alumina

WANG Tao,WANG Bo,HOU Baoqiang,SHI Zhongqi,YANG Jun,XIA Hongyan,WANG Jiping,WANG Hongjie,YANG Jianfeng

DOI: https://doi.org/10.19691/j.cnki.1004-4493.2020.04.003

2020-01-01

Abstract:Porous alumina ceramics are widely used in various fields because of their unique characteristics in structure and properties. This article mainly provided an overview of preparation techniques of porous alumina ceramics; besides, the principles and the characteristics of pore-forming agents processes, gel-casting processes, freeze-casting processes,anodizing processes and other common processes in obtaining the required properties of porous alumina ceramics were introduced. Meanwhile, the relevant applications and the performance of porous alumina ceramics were described. The research prospects of porous alumina ceramics were put forward based on the research status at the end of this paper.
Research Progress on Preparation and Application of Porous Ceramics Materials

欧鹏飞,王帅,钟宏,吴诗婷,唐新阳

DOI: https://doi.org/10.3969/j.issn.1001-9677.2010.07.004

2010-01-01

Abstract:Some features of porous ceramics materials were introduced.The new development and theories of the preparation of porous ceramics materials in China and aboard in recent years were summarized.The preparation of porous ceramics materials,especially the selection of raw materials,the molding process and pore-forming process were analyzed.The applications of porous ceramics materials in the fields of filtration,catalyst,sound absorption and insulation were also included.
A Study on Al2TiO5-Al2O3 Composite Ceramics

Jian-hua CHEN,Hong-bin LU,Chun-xia FENG,Wen-dan LI,Yue-yuan SHAN

DOI: https://doi.org/10.3969/j.issn.1008-2794.2008.02.015

2008-01-01

Abstract:Al2TiO5-Al2O3 composite ceramics were prepared by one step firing and two steps firing.The effects of sintering process and raw material composition of Al2TiO5-Al2O3 composite ceramics on the performances were studied.The results indicate that the composition and sintering process of the Al2TiO5-A12O3 composite ceramics have an important influence on the performances.The combination properties of the Al2TiO5-Al2O3 composite ceramics those prepared by one step firing are better than those prepared by two steps firing.When the composite ceramics with the composition of 80wt% alumina and 20wt% aluminium titanate are prepared by one step firing,the water absorptivity of the Al2TiO5-Al2O3 composite ceramics is only 0.11%,the open porosity is 0.32%,the bulk density is 3.00 g·cm-3,the bending strength reaches 152.88 MPa,and the thermal-expansion coefficient is 7.5×10-6/℃.
Research Development of Preparation Technology of Porous Si3N4 Ceramics

李坊森,周万城,胡汉军,罗发,朱冬梅

DOI: https://doi.org/10.3321/j.issn:1005-023x.2008.10.005

2008-01-01

Abstract:Porous Si3N4 ceramics have been a hot research area because of the excellent mechanical behavior. The main preparation methods are reviewed in the paper,in view of the composite design,the molding methods and the sintering condition respectively. The advantages and disadvantages existing in these preparation methods are analyzed. The future research work will be focused on the quantification of these preparation methods for excellent porous ceramics and new ones for the low-cost preparation technology.
Recent development of Al_2O_3 based composite nanoceramics

Chen Yubai,Fan Jinglian,Tian Jiamin,Yin Ruiming

2007-01-01

Abstract:The recent development in preparation and sintering and mechanical properties of Al2O3 based composite nanoceramics as well as their strengthening and toughening mechanisms are summarized.Application prospects and research directions of the nanoceramics are proposed.
Study on Laser Ablation Mechanism and Laser Machining Technology of AlON Ceramic Materials

Wentao Qin,Qingliang Zhao,Chunyu Zhang,Guo Li,Chengwei Song,Yandi Huang

DOI: https://doi.org/10.1117/12.2656490

2023-01-01

Abstract:AlON ceramic is widely used in the fabrication of high-quality infrared optical components, and has broad application prospects in aerospace, transparent armor, and infrared weapon windows. A laser can be applied to the processing of AlON ceramic in order to achieve a more flexible and efficient processing of AlON ceramic. In this paper, laser drilling experiments were carried out on AlON samples to investigate the mechanism of laser processing of AlON ceramic. A two-dimensional simulation model of laser ablation of AlON ceramic was established, and the process of material removal was analyzed. By comparing the experimental results with the theoretical analysis, the effect of defocus distance on the quality of AlON laser processing is analyzed.
Research Progress of Plasma Electrolytic Oxidation Technology and Mechanism

WANG Li,FU Wen,CHEN Li

DOI: https://doi.org/10.3969/j.issn.1004-227x.2012.04.012

2012-01-01

Abstract:Plasma electrolytic oxidation(PEO) is a technology that can grow in-situ ceramic films on light metal surfaces,and has a wide application future in material field.The research progress of action processes,mechanism,plasma diagnosis technology,properties of PEO ceramic film and related influencing factors,application,and limitation of PEO were summarized.The development directions of PEO were pointed out.
Preparation of High Purity Alumina Technology Overview

Xiu Feng Fu,Ben Jun Xu,Cai Juan Huang

DOI: https://doi.org/10.4028/www.scientific.net/amr.734-737.2496

2013-08-16

Advanced Materials Research

Abstract:high purity alumina preparation process status of recent years is introduced, and the advantages and disadvantages are summarized.
Effect of Al2O3 on Properties of Plasma Sprayed Cr2O3/TiO2/Al2O3/SiO2 Composite Ceramic Coating

Bi JIA,Fu-sheng PAN,Chun-jiang CHEN,Rong XU,Han-mei JIANG,Ru-zhuan WANG,Yong-jiang DI

DOI: https://doi.org/10.16490/j.cnki.issn.1001-3660.2020.08.007

2020-01-01

Surface Technology

Abstract:The work aims to study the effect of Al2O3 on the properties of Cr2O3/TiO2/Al2O3/SiO2 quaternary composite 专题——热喷涂技术研究及应用 ·56· 表面技术 2020 年 8 月 ceramic coating. The composite ceramic coatings with different Al2O3 contents were deposited on the surface of X80 pipeline steel by plasma spraying. In addition, all coatings were prepared on preheated and unpreheated substrates to show the effect of substrate temperature on the coating properties. Then, the porosity, hardness, adhesion and electrochemical corrosion performance of the coatings were measured by boiling weighing method, Vickers hardness tester, scratch tester and electrochemical workstation, respectively. The phase composition and morphology characteristics of the coatings with different Al2O3 contents were analyzed by X-ray diffraction (XRD) and scanning electron microscopy (SEM). The effects of substrate temperature and Al2O3 content on the coating properties were studied. With the increase of Al2O3 content, the porosity of Cr2O3/TiO2/Al2O3/SiO2 quaternary composite ceramic coating decreased firstly and then increased, while the adhesion and dimensional hardness of the corresponding quaternary composite ceramic coating increased firstly and then decreased. When Al2O3 mass fraction was 60%, the performance of the quaternary composite ceramic coating was the best, with porosity of 3.6%, hardness of 824.6HV and adhesion of 53.8 N. The electrochemical corrosion test showed that the corrosion resistance of the coating was improved by Al2O3. When Al2O3 mass fraction was 60%, the self corrosion potential of the coating was the highest, −0.28 V. In addition, under the preheating and unpreheating conditions, the properties of the coating varied with the Al2O3 content, but preheating was more beneficial to improving the coating properties than unpreheating. The addition of Al2O3 can not only effectively reduce the Cr content of the coating, but also significantly improve the properties of the quaternary composite ceramic coating, especially the corrosion resistance. In addition, the substrate should be preheated before plasma spraying, which is beneficial to improving the coating properties.
INDUSTRIAL PREPARATION OF ALUMINA POWDER AND ITS DEVELOPMENT IN CHINA.

zheng shiyuan,chen jian,pan wei

DOI: https://doi.org/10.3969/j.issn.1006-4990.2000.03.007

2000-01-01

Abstract:A variety of preparation methods of alumina powder used in ceramic industry are reviewed. The corresponding principles and processes are also discussed. With the development of science and technology , the demand of ultra - fine, high - purity alumina powder is increased. A brief survey of its preparation methods is given, the present status of alumina industry development in China is analysed and some suggestions to improve its competitiveness are presented.
Aluminum Alloy Surface-Ceramic Technology Based on Plasma Electrolytic Oxidation and Laser Melting and Solidification

Jie Yu,Shichun Di,Junjie Yang,Yan Wang

2014-01-01

Abstract:A compound technology of plasma electrolytic oxidation (PEO) and laser melting and solidification (LSM) technologies which could produce a ceramic coating on the aluminum surface was introduced. The plasma phenomenon during the LSM and PEO coatings interactions produced by three different kinds of plasma were analyzed. The relationship between PEO and LSM process in the compound technology was further demonstrated. The measuring results of SEM and ultra micro hardness tester proved that the porosity factor of the ceramic coating was lowered while the density and hardness were promoted by LSM.
Progress of Research on the Alumina Ceramics Metallization

MA Yuan-yuan,WANG De-miao,REN Gao-chao

DOI: https://doi.org/10.3969/j.issn.1002-8935.2007.05.011

2007-01-01

Abstract:Recent domestic and international developments of alumina ceramics metallization were reviewed.Several commonly used metallization techniques were introduced.The influence on metallization quality cased by the film material,thickness and technique parameters in vacuum sputtering were analyzed.

Study on Preparation Technology of Al2O3 Ceramics

Progress in Preparation of Nanocrystalline Alumina Ceramics

Recent Progress of High Purity Al2O3 Ceramic

Application of Plasma Technique in the Development of Ceramic Material

Preparation of Al2O3 Ceramic Coating by Electrolytic Plasma Processing and Its Properties

Research on the Organization of Ceramic Coating by Plasma Spraying

Preparation and Characterization of Al-Al2O3 Metal Ceramics Via Powder Metallurgy Methods

Preparation and Characterization of Nanoporous Alumina As Ceramic Membrane Materials

Ceramic Thin Coating Prepared by Micro-plasma Oxidation

Preparation and Application Progress of Porous Alumina

Research Progress on Preparation and Application of Porous Ceramics Materials

A Study on Al2TiO5-Al2O3 Composite Ceramics

Research Development of Preparation Technology of Porous Si3N4 Ceramics

Recent development of Al_2O_3 based composite nanoceramics

Study on Laser Ablation Mechanism and Laser Machining Technology of AlON Ceramic Materials

Research Progress of Plasma Electrolytic Oxidation Technology and Mechanism

Preparation of High Purity Alumina Technology Overview

Effect of Al2O3 on Properties of Plasma Sprayed Cr2O3/TiO2/Al2O3/SiO2 Composite Ceramic Coating

INDUSTRIAL PREPARATION OF ALUMINA POWDER AND ITS DEVELOPMENT IN CHINA.

Aluminum Alloy Surface-Ceramic Technology Based on Plasma Electrolytic Oxidation and Laser Melting and Solidification

Progress of Research on the Alumina Ceramics Metallization