Abstract:Coarse tungsten powders are usually used as raw material for preparing coarse grained WC-Co cemented carbides. Sodium can effectively promote the growth of tungsten powder during the reduction of tungsten oxide with hydrogen. Conventional addition of sodium salt into tungsten oxide powders by mechanical milling has the disadvantage of uneven distribution of sodium, which leads to abnormal growth of tungsten powders and affects the performance of WC-Co cemented carbides. In this study, uniform sodium doped ammonium paratungstate (APT) was prepared by adding sodium carbonate into ammonium tungstate solution during the evaporation and crystallization process based on the formation of ammonium-sodium paratungstate. Experimental results showed that sodium was uniformly distributed in the APT and promoted the growth of APT crystal. The sodium-doped APT was then used to produce coarse tungsten powders. Compared with tungsten powders obtained from tungsten trioxide with addition of sodium by mechanical milling, the coarse tungsten powders had larger average particle size and more uniform particle size distribution . The coarse tungsten powders were subsequently prepared into tungsten carbide powders and WC-Co cemented carbides by carburization and pressure sintering, respectively. Results showed that the obtained WC-Co cemented carbides had larger average WC grain size (6.8–7.2 μm), higher fracture toughness and transverse ruptures strength, and more uniform microstructure than that of WC-Co cemented carbides obtained by addition of sodium with mechanical milling. Moreover, sodium thoroughly volatilized during hydrogen reduction and carburization process, so that the purity of WC-Co cemented carbides was not reduced. Therefore, this study provided a new route for preparation of extra coarse-grained WC-Co cemented carbides.

Effect of Cobalt Adulterant on Particle Size and Microscopic Morphology of Coarse and Ultra Coarse Tungsten Carbide Powder

Influences of Ni/Cu/Cr3C2 Composite Additive on Microstructure and Properties of WC–10Co Fine Grained Hardmetal

The Effect of A Small Amount of Tungsten on the Microstructure of Mechanically Alloyed Ag37cu63

Enhanced the Mechanical Properties and Corrosion Resistance of Ultra-Coarse Grain WC-8Co Cemented Carbides by the Introduction of Cu and Ni

Effects of Lower Cobalt Binder Concentrations in Sintering of Tungsten Carbide

Preparation of Ultra-Fine WC-Co Cermet and Its Wear Behavior

Comparative Study on Microstructure and Mechanical Properties of Coarse-grained WC-based Cemented Carbides Sintered with Ultrafine WC or (W+C) as Additives

Effect of carbon content on the microstructure and properties of Cr-doped WC–15Co cemented carbide

Microstructure and properties of ultrafine WC–Co–VC cemented carbides with different Co contents

Abnormal Grain Growth of WC with Small Amount of Cobalt

Ultrafine and Nanoscaled Tungsten Carbide Synthesis from Colloidal Carbon Coated Nano Tungsten Precursor

Performance Enhancement of Ultra-Coarse Cemented Carbide by Boride Additives

Effect of carbon content on the properties of inhomogeneous cemented carbides with fine-grained structures produced via one-step transformation

Decarbonization and Its Improvement of Coarse-Grained Low Cobalt Cemented Carbide Sintered by Microwave Irradiation

Preparation of extra coarse-grained WC-Co cemented carbides by doping sodium in the ammonium tungstate solution during evaporation crystallization process

Effect of particle size and high-energy ball milling time on microstructure and mechanical properties of WC-10Co cemented carbides with plate-like WC grains

Effect of initial WC particle size on grain growth behavior and gradient structure formation of bilayer functionally graded cemented carbides

Influencing Factors on Hardness and Impact Toughness of the WC-Co Cemented Carbide Studied by Variables Search Method

Effect of Cr3C2 Addition on Microstructure and Mechanical Properties of WC-CoNiFe Cemented Carbides

Effect of WC grain size on mechanical properties and microstructures of cemented carbide with medium entropy alloy Co-Ni-Fe binder

Microstructure Evolution in the Cemented Carbides Wc-Coi. Effect of the C/W Ratio on the Morphology and Defects of the Wc Grains