Abstract:Structural evolution and mechanical performances of rapidly solidified Ni95Ge5 and Ni33Ge67 alloys were investigated under two conditions involving drop-tube containerless processing and copper-mold injection casting. As the cooling rate increased, the coarse dendritic structure of the primary (Ni) phase for Ni95Ge5 alloy changed to equiaxed grains structure, and the microstructure of Ni33Ge67 alloy showed a transition from coarse (NiGe + Ge) eutectic to refined structure plus some primary Ge phase. Containerless processing can produce finer microstructures than those of injection casting owing to higher cooling rate. Nanoindentation measurements indicated that both alloys showed a remarkable enhancement of Vickers hardness along with the microstructural evolution, and the hardening mechanism for a single-phase alloy was found to be grain-boundary strengthening, while that of the eutectic alloy was attributed to the multiphase coordinated strengthening. The strain hardening exponents of Ni95Ge5 and Ni33Ge67 alloys were calculated as 0.28 and 0.77, respectively. The special morphology evolution and lower strain hardening exponent of Ni95Ge5 alloy remarkably improved the hardening ability. Its hardness increased up to 56.6% that was much higher than the eutectic alloy. Moreover, these alloys displayed different relations between hardness and strength. The average ratio of hardness to strength for Ni95Ge5 alloy was 2.75, while that for Ni33Ge67 alloy was 9.09. Both the experimental evidence and theoretical analysis revealed that obvious enhancements of hardness and strength were achieved using a high cooling rate; thus, the drop-tube processed alloy particles showed better mechanical properties than those of the as-cast alloys owing to their higher cooling rates. It is obvious that rapid solidification conditions can improve the mechanical properties of both the alloys to various degrees.

Effect of cooling rate on microstructure and mechanical properties of rapidly solidified Al-based bulk alloys

Effects of Cooling Rates on the Solidification Behavior, Microstructural Evolution and Mechanical Properties of Al–Zn–Mg–Cu Alloys

Effect of cooling rate on microstructure and mechanical properties of Mg-9Gd-4Y-1Zn-1Al alloy

Effect of Cooling Rate on Solidification Parameters and Microstructure of Al-7Si-0.3Mg-0.15Fe Alloy

Microstructure Evolution and Mechanical Properties of a Cast and Heat-Treated Al–Li–Cu–Mg Alloy: Effect of Cooling Rate During Casting

Effect of Cooling Rate on Microstructure and Mechanical Properties of an Al-5.0Mg-3.0Zn-1.0Cu Cast Alloy

Influence of Cooling Rate on the Microstructure and Mechanical Properties of Al–Cu–Li–Mg–Zn Alloy

Effect of Cooling Rate on Solidified Microstructure and Mechanical Properties of Aluminium-A356 Alloy

Effect of Cooling Rate on the Microstructure and Microhardness of the CuZrAgAl Alloy

Microstructural Evolution and Mechanical Properties of Rapidly Solidified Ni-Ge Alloys

Effect of Cooling Rate on Solidification Microstructure and Properties of Al-Cu Binary Alloy

The Effect of Cooling Rate on the Microstructure and Mechanical Properties of Mg–Zn–Gd-based Alloys

Effects of cooling rate and pressure on microstructure and mechanical properties of sub-rapidly solidified Mg-Zn-Sn-Al-Ca alloy

Effects of Cooling Rate and Component on the Microstructure and Mechanical Properties of Mg–Zn–Y Alloys

The Effects of Cooling Rate on Solidification Microstructure of Cu70Ni30 Alloy

Effects of cooling rate on solidification structure of Al-5Zr master alloys

Effects of cooling rates on microporosity in DC casting Al-Li alloy

Effects of Cooling Rate on Solidification and Microstructure of Al-4.5Mg-0.7Mn-0.4Er Alloy

Microstructural evolution and mechanical property of Al–Mg–Mn alloys with various solidification cooling rates

Effects of cooling rates on solidification of CuCr25 alloys

Effects of Rapid Cooling Rate on Microstructure Formation and Microhardness of Binary Ti-44Al Alloy