Abstract:The ability to undercool and solidification mechanism of liquid quinary Ni40Zr28.5Ti16.5Al10Cu5 alloy are investigated by electromagnetic levitation (EML) and drop tube (DT) technique. Under the EML condition, the maximum undercooling of levitated alloy can reach up to 290 K (0.21TL). Under the DT condition, the alloy achieves higher undercooling than EML, and solidifies finally into metallic glass. At lower undercooling, the solidification structure of the alloy is composed of primary Ni3Ti phase, secondary Ni10Zr7 phase and eutectic (Ni10Zr7+Ni21Zr8) phase. With the rise of undercooling, the solidification structure displays the following evolution events: phase morphology refinement, primary phase inhibition, phase number reduction, and amorphous phase formation. By using the high-speed cinematography technique, three nucleation modes are distinctly observed on the levitated alloy melt surface at the beginning of solidification, that is, single-point nucleation, multi-point nucleation and annular nucleation. The levitation state corresponding to single-point mode nucleation is relatively stable, and the alloy undercooling is also relatively low. The annular nucleation only occursin the case with high rotation speed, and the undercooling is greater than 208 K. The discrepancy between nucleation modes is due to the He gas flow for forced cooling. The theoretical calculations indicate that the alloy droplets achieve high undercoolingand large cooling rate under the DT condition. The experimental results show that when the droplet diameter decreases to 498 μm, the amorphous phase begins to appear in the alloy particles. It is noteworthy that the amorphous phase is preferentially formed inside the droplet, but not on the outer surface. The morphology of solidification structure reveals that different regions of the droplet have various local undercoolings, which result in the distribution characteristics of amorphous phase. The volume fraction of amorphous phase increases linearly with the decrease of particle diameter. When the droplet diameter decreases to 275 μm, the alloy droplets are completely frozen into glassy particles. The average eutecticspacing values are also measured at different alloy undercoolings. Compared with the classical binary eutectic growth model, the experimental eutectic growth law exhibits a large deviation in index. This indicates that the eutectic growth in multicomponent alloys displays more complex kinetic characteristics.

Effects of Rapid Cooling Rate on Microstructure Formation and Microhardness of Binary Ti-44Al Alloy

Combined Effects of High Undercooling and Large Cooling Rate on the Microstructure Evolution and Hardening Mechanism of Rapidly Solidified Ti-Al Alloys

Microstructure and Microhardness of Ti-48Al Alloy Prepared by Rapid Solidification

Effect of Cooling Rates on Microstructures Evolution and Nanohardness of Rapidly Solidified Ti-48Al-4Cr Alloy

Formation Mechanism of B2 Phase and Micro-Mechanical Property of Rapidly Solidified Ti-Al-Nb Alloy

Effects of Solidification Rates on Microstructure Refinement and Elemental Distribution of Ti44Al6Nb1.0Cr2.0V0.1B0.15Y Alloy by Rapid Solidification

Rapid Solidification of Ti-6Al-4V Alloy Micro-Droplets Under Free Fall Condition

Microstructure and nanohardness of Ti-48%Al alloy prepared by rapid solidification under different cooling rates

The Effect of Cooling Rate on the Microstructure Change During Rapid Solidification of Liquid Ti3Al Alloy

Microstructure Evolution and Nano-Hardness Modulation of Rapidly Solidified Ti–Al–Nb Alloy

Effect of Heat Treatment on Microstructures Evolution of Rapidly Solidified Ti-48Al-4Cr Alloy

Effect of cooling rate on the grain refinement of TiAl-based alloys by rapid heat treatment

Effect of cooling rate on solidification microstructure and mechanical properties of TiB2-containing TiAl alloy

Effect of Wheel Speed on the Microstructure and Nanohardness of Rapidly Solidified Ti–48Al–2Cr Alloy

Rapid Solidification Mechanism of Liquid Quinary Ni-Zr-Ti-Al- Cu Alloy Investigated by High-Speed Cinematography

Microstructure study of rapidly solidified TiAl-Cr-xNb-Y alloys

Effect of Cr Addition on Microstructures and Nanohardness of Rapidly Solidified Ti–48Al Alloy

Effects of the cooling rate on mechanical properties and microstructure of near- α Ti-6Al-3Zr-2Nb-Mo alloy

Effect of cooling rate on microstructure and mechanical properties of rapidly solidified Al-based bulk alloys

Effects of Cooling Rate on Microstructure of TiAl Alloy with Coarse Grain

Effect of cooling rate on the microstructure evolution of a forged TiAl based alloy