Abstract:WCoB-TiC composite coatings with in-situ formation of NbC were fabricated on the surface of an AISI 1045 substrate by laser cladding. The geometric characteristics, microstructure, microhardness, and fracture toughness of coatings were investigated by means of an optical microscope (OM), a scanning electron microscope (SEM), energy-dispersive spectroscopy (EDS), X-ray diffraction (XRD), an electron probe microanalyzer (EPMA), and a microhardness tester. In addition, the elastic constants and bulk property of the reinforced phases were investigated by first principles calculation. The results showed that a reliable metallurgical bonding was formed between the coating and the substrate and in-situ synthesized reinforcement phases of the coating consisted of WCoB, W2CoB2, TiC, NbC, (Nb,Ti,W)C, and traces of Nb2C. The dilution rate and porosity had a negative effect with the addition of Nb. According to the results of SEM, EDS, and EPMA, Nb was diffused uniformly in the TiC structure. The NbC phase had the highest hardness among all in-situ synthesized reinforcement phases, which reached 24.525 GPa, while Nb2C reflected the strongest metallicity. The microhardness and fracture toughness of the coating were increased firstly and then decreased following the increase of Nb content, and when the Nb addition was 4 wt%, the coating had the highest average microhardness and fracture toughness (1755.42 HV0.5, 8.23 MPa·m1/2, respectively). The microhardness and fracture toughness was 24% and 30% higher than that of the coating without Nb addition, respectively. From the crack propagation morphology of coatings, all coatings had fine transgranular fracture.

In Situ Formation of NbC Reinforced Ni3Si Intermetallic Compounds by Laser Cladding

Fabrication of Ni-Based Composite Coating Reinforced with NbC Particles by Laser Cladding

Microstructure and Wear Resistance of in Situ NbC Particles Reinforced Ni-based Alloy Composite Coating by Laser Cladding

Effect of NbC in-situ synthesis on the microstructure and properties of pre-placed WCoB-TiC coating by laser cladding

Effect of in Situ NbC on Microstructure and Wear Properties of Laser Cladding Co-Based Coatings

Laser cladding of Ni-base composite coatings onto Ti-6Al-4V substrates with pre-placed B4C + NiCrBSi powders

Research on Microstructure Properties of the TiC/Ni-Fe-Al Coating Prepared by Laser Cladding Technology

Experimental Study of the Microstructure and Micromechanical Properties of Laser Cladded Ni-based Amorphous Composite Coatings

Microstructural Characterisation of Laser Clad Coating of Nickel Based Alloy with Dissolved Sicp

Microstructure of Laser-Clad SiC-(Ni Alloy) Composite Coating

Structure and Properties of NiCrSiB Alloy Laser Cladding

Wear Resistance of In Situ NbC-Reinforced Laser Cladding Ni45 Coatings

Influence of Nb on the microstructure of laser clad composite coating reinforced by in-situ particles

Microstructures and Properties of Laser-Clad in Situ Particle Reinforced Ni-Base Composite Coating on 55mn Steel

Laser cladding Ni-base composite coatings reinforced by in-situ synthesized multiple carbide particles

Effects of NbC content on microstructural evolution and mechanical properties of laser cladded Fe50Mn30Co10Cr10-xNbC composite coatings

Effects of the Proportions of Carbon on the Microstructure and Properties of NbC-Reinforced Ni-WC Composite Coatings by Laser Cladding In-situ Synthesis

Microstructure Characteristics and Properties of In-Situ Formed Tic/Ni Based Alloy Composite Coating by Laser Cladding

Microstructure and Property of Fe–Co–B–Si–C–Nb Amorphous Composite Coating Fabricated by Laser Cladding Process

Microstructures and Properties of NbC-Reinforced Ni-Based Coatings Synthesized In Situ by Ultrasonic Vibration-Assisted Laser Cladding

Study of Fe-Ni(Cr) Alloy and Nano-Al2o3 Particles Composite Coating Prepared by Laser Cladding