Abstract:Introduction: During warm vertical compaction of gutta-percha, root canal sealers with different chemical compositions absorb the heat generated inside the root canal. The aim of this research was to assess physicochemical modifications of sealers subjected to the System B heat source (Analytic Technology, Redmond, WA) and to evaluate the effect that the use of different sealers has on the heat transfer to the external root surface. Methods: Three proprietary brand sealers (AH Plus [Dentsply International, Addlestone, UK], Pulp Canal Sealer [Kerr Corporation, Orange, CA], MTA Fillapex [Angelus Dental Solutions, Londrina, PR, Brazil]) and a prototype sealer based on Portland cement were assessed. The heat generated on the surfaces of System pluggers and the heat dissipation at different levels (apical, midroot, and cervical) over root surface while using different sealers was assessed using thermocouples. Data were collected in 3 different environmental conditions with the tooth suspended in air, immersed in Hank's balanced salt solution, or gelatinized Hank's balanced salt solution. Chemical changes in the sealers induced by the heat were monitored by Fourier transform infrared spectroscopy. The effect of heat changes on the setting time and compressive strength of the sealers was also assessed. Results: The continuous wave plugger sustained a rise in temperature at a maximum of 80°C at the instrument shank. The highest change in temperature on the external root surface was recorded after 1.5 minutes from the start of heating, and it was restored to body temperature by 6 minutes. Environmental conditions affected heat dissipation for all the sealers in the midroot and cervical regions and the highest increase in temperature (∼60°C) recorded in air. In the midroot and cervical regions, the type of sealer used did not affect the rise in temperature. In the apical region, AH Plus obturations resulted in a greater rise in temperature, and the chemical composition of this sealer was affected by high temperature; it also induced a reduction in sealer setting time and strength. Conclusions: It could be concluded that surrounding conditions, such as temperature and humidity, exerted influence on heating dissipation during the continuous wave of the condensation obturation technique and that root canal sealers presented different conductive/isolating properties. Furthermore, the physical and chemical properties of AH Plus were negatively affected by the changes in temperature.

Heat transfers to periodontal tissues and gutta-percha during thermoplasticized root canal obturation in a finite element analysis model.

Periodontal Blood Flow Protects the Alveolar Bone from Thermal Injury during Thermoplasticized Obturation: A Finite Element Analysis Study

Influence of Relative Positions of the Heat Carrier and Lateral Canal Opening on Gutta- Percha Obturation of Lateral Canals in a Three-Dimensional-printed Model

Investigation of the effect of sealer use on the heat generated at the external root surface during root canal obturation using warm vertical compaction technique with System B heat source

Comparing Warm and Cold Gutta-Percha Techniques for Root Canal Filling: An In Vitro Study

An in Vitro Comparison Study on Sealing Ability of Four Thermoplasticized Guttapercha Obturation Techniques with Cold Lateral Condensation

The accuracy of using guided endodontics in access cavity preparation and the temperature changes of root surface: An in vitro study

Heat Transfer and Thermal Stress Analysis of a Mandibular Molar Tooth Restored by Different Indirect Restorations Using a Three-Dimensional Finite Element Method

In Vitro Experiment on the Sealing Ability by High-Temperature Thermoplasticized Injectable Technique and Cold Lateral Condensation

The role of protective liners and glass ionomer in managing pulp temperature during light curing

Apical placement of needle tip with an injection-thermoplasticized gutta-percha technique for root canal obturation

In vitro evaluation of temperature change on the root surface after the removal of root canal filling

Differences of Micro-CT evaluation of the obturation sealing capability between thermoplastic carrier-based condensing techniques and lateral heat condensation techniques

Assessment of the root surface temperature during the use of intracanal agitation systems: In vitro study

Influence of Warm Vertical Compaction Technique on Physical Properties of Root Canal Sealers.

Thermal transfer in extracted incisors during thermal pulp sensitivity testing

A Comparative Study of Temperature Variations in Incisor Root Surfaces During Root Canal Preparation Using Various Rotary Systems and Irrigation Protocols

In Vitro Root Surface Temperature Rises During Root Canal Obturation by BeeFill~(TM) 2in1 Technique

Outcome of Root Canal Obturation by Warm Gutta-Percha Versus Cold Lateral Condensation: A Meta-analysis

Effect of composite temperature on in vitro intrapulpal temperature rise

Evaluation of Apical Overfilling and Sealing with 4 Different Obturation Techniques in Oval-root Canals In Vitro