Abstract:In this investigation, hybrid AA2024 – Si3N4 (0–6 wt.% @ 2%) – SiC (2 wt.%) – graphite (2 wt.%) alloy composites have been fabricated as per design using the stir casting method. This follows evaluation of physical, mechanical, thermal, thermo-mechanical, fracture toughness, and sliding wear performance as per standards. The density and material stability of the alloy composites improves with reinforcement content while porosity and thermal conductivity show a diminishing trend. The mechanical characteristics improve considerably with reinforcement. The alloy composite having 6 wt.% Si3N4 particulates show maximum mechanical characteristics like ultimate tensile strength (212 MPa), percent elongation (13%), flexural strength (645 MPa), micro-hardness (127 HV), and impact strength (85 J). Fracture toughness was found to improve with Si3N4 particulate content and with crack length. The storage modulus and damping capacity of the alloy composites have shown an increasing trend with reinforcement content while the loss modulus shows a reverse trend. The specific wear rate and friction coefficient tend to diminish with Si3N4 particulate content under steady state conditions. The normal load significantly influences the specific wear rate of the alloy composites under the Taguchi experimental design. Worn out surface morphology analysis shows wear mechanisms like surface fatigue, ploughing, micro-cutting, three-body abrasion, etc. responsible for surface damage. EDAX spectrum shows elemental presence and mapping and XRD analysis shows the presence and distribution of various phases of alloy composites and counter-surface disc. It could be the potential material for various components like gear, piston, cylinder liner, etc.

Influence of SiC Addition on Tribological Properties of SiAlON

Wear Behaviour and Microstructural Changes of SiCw-Al Composite under Unlubricated Sliding Friction

Tribological Behavior of Liquid Phase Sintered SiC Ceramics Under Dry Condition

Effect of SiC Weight Percentage on Tribological Characteristics of Al7075/SiC Composites

Effect of SiC Content on Mechanical and Tribological Properties of Al2024-SiC Composites

Effect of Carbon in Fabrication Al-SiC Nanocomposites for Tribological Application

Tribological behavior of aluminum matrix composites reinforced with ceramic particulates in dry sliding against a semimetallic friction material

Exploring tribological properties in the design and manufacturing of metal matrix composites: an investigation into the AL6061-SiC-fly ASH alloy fabricated via stir casting process

Mechanical Properties and Tribological Behavior of Al6061–SiC–Gr Self-Lubricating Hybrid Nanocomposites

Investigation of Mechanical and Tribological Properties of Al–7 Wt.% Si alloy Metal Matrix Composites Reinforced with SiC

Effect of the pin temperature and SiC reinforcement on dry sliding tribological behavior of aluminium based silicon carbide metal matrix composite (Al-SiC) using Taguchi approach

Tribological Behavoiur of Silicon Carbide/ Rice Husk ash Reinforced Al7075 Hybrid Composites Using Optimization Techniques

Investigation of the solid self-lubricating effect on tribological properties of Al/SiC/Gr composites against steel disc

Effect of Si3N4 Ceramic Particulates on Mechanical, Thermal, Thermo-Mechanical and Sliding Wear Performance of AA2024 Alloy Composites

Microstructure, Mechanical and Tribological Properties of CrSiC Coatings Sliding Against SiC and Al2O3 Balls in Water

Microstructure, mechanical and friction-wear properties of SiC-WC composite with Al and C as sintering aids

Enhancement of Tribological Properties in Siliconized Graphite Via Hierarchically Hybrid SiC/C Composite

Investigation of Impact of C/Si Ratio on the Friction and Wear Behavior of Si/SiC Coatings Prepared on C/C-SiC Composites by Slurry Reaction Sintering and Chemical Vapor Infiltration

Mechanical and Tribological Properties of SiC Whisker‐reinforced SiC Composites Via Oscillatory Pressure Sintering

SiC honeycomb reinforced Al matrix composite with improved tribological performance

Appraisal of tribological properties of A356 with 20% SiC composites under dry sliding condition