Abstract:Magnesium alloys are still attractive materials for applications that necessitate light weight due to their low density, moderate strength, and good corrosion resistance. AZ91 is one of the widely applied magnesium alloys due to its very good castability and strength. However, one of the drawbacks of magnesium alloys is the low elastic modulus. So, reinforcing AZ91 with carbon short fibers with the aim of further increasing the strength and improving the elastic modulus is investigated in this study. Squeeze cast AZ91-23 vol.% carbon short carbon (AZ91-C) and the unreinforced AZ91 are deeply examined by tensile testing at different temperatures (20, 100, 150, 200, 250, and 300 °C). Tensile stress-strain curves are measured and the tensile parameters (yield stress, ultimate tensile strength and strain) are defined and presented against the test temperature. Yield stress of AZ91 at 20 °C (109 MPa) is doubled (226 MPa) in the reinforced AZ91-C. Yield stress is found to slightly decrease with increasing the test temperature. Ultimate tensile strength of AZ91 at 20 °C (198 MPa) is increased (262 MPa) in the reinforced AZ91-C. The improvement of the ultimate tensile strength due to reinforcing increases with increasing the test temperature. Flow curves are determined and described by a modified Mecking-Kocks relationship and the flow parameters are determined and described as a function of the test temperature. Microstructure investigation was undertaken of the fractured tensile specimens at the grain boundaries rich in eutectic structure formed at the grain boundaries. Mixed brittle/ductile fracture mode is detected on the fracture surface of unreinforced AZ91, while the SEM investigations show matrix/carbon fiber detachment and fiber fracture as main fracture modes.

Fracture behavior of AZ91 magnesium alloy

Fracture Mechanism of Magnesium Alloys at Room Temperature

Mechanical Properties and Fracture Surface Analysis of AZ91D Prepared with Direct Smelting of Crude Magnesium

The Fracture Morphology Analysis of Extruded AZ31 Magnesium Alloy under High Strain Rate Loading

Failure Behavior of High Pressure Die Casting AZ91D Magnesium Alloy

Impact fracture mechanism of Mg-Gd-Y-Zn-Zr magnesium alloy

Fracture Behavior of High Strength Mg-Gd-Y-Zr Magnesium Alloy

Tensile Deformation and Fracture of Unreinforced AZ91 and Reinforced AZ91-C at Temperatures up to 300 °C

Mechanical properties and fracture behavior of Mg–3Al–1Zn alloy under high strain rate loading

Fracture Failure Analysis of Twin Rolling Casting Magnesium by Hot Compression

Tensile Fracture of As-Cast and Hot Rolled Mg-Zn-Y Alloy with Long-Period Stacking Phase

Mechanical properties and failure behavior of AZ61 magnesium alloy at high temperatures

Influences of stress states and loading directions on the anisotropic fracture of magnesium alloy AZ31B sheet under tension-dominated forming conditions

Tensile Properties And Fracture Mechanism Of Friction Stir Weld On Az31 Magnesium Alloy

Fracture Mechanism of Friction Stir Welded AZ31 Magnesium Alloy

Fracture Behavior of Low-Pressure Sand-Cast Mg–Gd–Y Magnesium Alloy Under Different Types of Loads

Investigation Of Hot Cracking Behavior Of Az91 Magnesium Alloy

Mechanical Behavior of Al–Zn–Mg–Cu Alloy under Tension in Semi-Solid State

Study on Behavior of Dynamic Fracture in SiC Nanoparticles Reinforced Magnesium Matrix Composites

TENSILE FRACTURE IN AN AL-LI ALLOY-8090

Strain-controlled cyclic deformation behavior of cast Mg–2.99Nd–0.18Zn–0.38Zr and AZ91D magnesium alloys