Α-Fe2o3 Nanowires. Confined Synthesis and Catalytic Hydroxylation of Phenol

F Jiao,B Yue,KK Zhu,DY Zhao,HY He

DOI: https://doi.org/10.1246/cl.2003.770

2003-01-01

Chemistry Letters

Abstract:alpha-Fe2O3 nanowires were prepared using mesoporous silica SBA-15 as a template and showed a remarkable catalytic activity for the hydroxylation of phenol with 30% H2O2 in aqueous solution at 343K.

What problem does this paper attempt to address?

Hydrothermal Synthesis and Characterization of Uniform Α-Feooh Nanowires in High Yield

Ping Ou,Gang Xu,Zhaohui Ren,Xiaohong Hou,Gaorong Han

DOI: https://doi.org/10.1016/j.matlet.2007.07.010

IF: 3

2008-01-01

Materials Letters

Abstract:Large-scale alpha-FeOOH nanowires with uniform diameter and high aspect ratios were synthesized via hydrothermal reaction at 100 degrees C. The obtained alpha-FeOOH nanowire was of diameter of 80 nm and length up to 1.2 mu m. X-ray diffraction (XRD) results show that the nanowires are of orthorhombic structure, and Fourier transform infrared (FT-IR) analysis further confirms the formation of orthorhombic phase alpha-FeOOH. High-resolution TEM (HRTEM) studies indicate the single-crystalline nature of alpha-FeOOH nanowires with an oriented growth along the [001] axis direction. Based on the results of contrastive experiments, the possible mechanism for hydrothermal synthesis of a-FeOOH nanowires was also discussed. (C) 2007 Elsevier B.V. All rights reserved.
Hydrothermal Conversion of Fe2o3/Sio2 Spheres into Fe2o3/Silicalite-1 Nanowires: Synthesis, Characterization, and Catalytic Properties

Pengfei Xie,Lifeng Chen,Zhen Ma,Chengyun Huang,Zhiwei Huang,Yinghong Yue,Weiming Hua,Yi Tang,Zi Gao

DOI: https://doi.org/10.1016/j.micromeso.2014.08.020

IF: 5.876

2014-01-01

Microporous and Mesoporous Materials

Abstract:Fe2O3 nanoparticles were dispersed onto SiO2 by impregnating amorphous SiO2 spheres with Fe(NO3)(3) followed by spray drying and calcination. Interestingly, the amorphous SiO2 spheres in the sample could be converted into Silicalite-1 nanowires after being hydrothermally treated in the presence of a mixture of ethylenediamine and triethylamine (dual templates) for over 4 days, whereas the Fe2O3 nanoparticles were still highly dispersed on the formed Silicalite-1 nanowires. Meanwhile, a fraction of Fe(III) species entered the zeolitic framework. Relevant characterization was conducted using X-ray fluorescence (XRF), N-2 adsorption-desorption, X-ray diffraction (XRD), scanning electron microscopy (SEM), transmission electron microscopy (TEM), ultraviolet-visible (UV-Vis) spectroscopy, electron paramagnetic resonance (ESR), X-ray photoelectron spectroscopy (XPS), and H-2-temperature-programmed reduction (H-2-TFR). The catalytic properties of the samples were studied using CO oxidation, N2O decomposition, and selective reduction of NO as probe reactions. (C) 2014 Elsevier Inc. All rights reserved.
Fe2O3/SiO2 Nanowires Formed by Hydrothermally Transforming SiO2 Spheres in the Presence of Fe3+: Synthesis, Characterization, and Catalytic Properties

Tao Meng,Pengfei Xie,Hengfei Qin,Huan Liu,Weiming Hua,Xi Li,Zhen Ma

DOI: https://doi.org/10.1016/j.molcata.2016.05.017

2016-01-01

Abstract:Xie et al. reported that Fe2O3/SiO2 spheres with a surface area of 111m2/g could be hydrothermally transformed into Fe2O3/Silicalite-1 nanowires in the presence of ethylenediamine and triethylamine. The resulting material was found to be active for CO oxidation and N2O decomposition due to the presence of small (1–2nm) Fe2O3 nanoparticles [P.F. Xie et al., Microporous Mesoporous Mater. 200 (2014) 52–60; P.F. Xie et al., J. Mol. Catal. A 409 (2015) 50–58]. In the current work, commercial amorphous SiO2 spheres with a low specific surface area of 9.5m2/g were found to be transformed into amorphous SiO2 nanowires via hydrothermal treatment at 200°C, in the presence of a mixture of ethylenediamine, triethylamine, and Fe(NO3)3, for several days. The Fe3+ species, in the presence of ethylenediamine and triethylamine, not only catalyzed the morphological transformation of SiO2, but also got deposited onto the SiO2 nanowires, forming supported Fe2O3 nanoparticles (2–4nm in diameter) upon subsequent calcination to remove the organic templates. For comparison, Fe2O3/SiO2 spheres prepared by impregnation had big Fe2O3 particles (as large as 50nm). Both the SiO2 supports and supported Fe2O3 particles were characterized by various techniques. The catalytic performance was studied, using N2O decomposition, CO oxidation, and photocatalytic reduction of Cr(VI) as probe reactions. Implications of the findings are discussed.
Preparation and Catalytic Property of Single Crystal Multiporousα-Fe_2O_3 Nanorods

ZHANG Yi,XU Gang,OU Ping,HAN Gao-Rong

IF: 1.292

2008-01-01

Journal of Inorganic Materials

Abstract:Theα-FeOOH nanorods were prepared via hydrothermal reaction of Fe(NO_3)_3·9H_2O and KOH at 100℃for 6h.Then theα-FeOOH nanords were heat treated at different temperautres,and single crystalline and multiporousα-Fe_2O_3 nanorods were obtained.The phase and morphology of the samples were characterized by XRD and TEM.The heat treatment process was investigated by TGA and FT-IR.The results show that the phase transition ofα-FeOOH→α-Fe_2O_3 occurrs between 239℃and 259.1℃.Theα-Fe_2O_3 still keeps in rod shape and lots of holes appear on the surface which disappear with the temperature increasing.The catalytic performance ofα-Fe_2O_3 nanorods was studied by decomposition of ammonium perchlorate(AP) based on DTA.The higher-temperature of exothermic peak of AP shifts towards low temperature whenα-Fe_2O_3 nanorods are introduced into the reaction, and the largest decrement reaches 71.4℃for theα-Fe_2O_3 nanorods heat treated at 350℃.
Effects of KOH and Temperature on Hydrothermal Synthesis of Α-Feooh Nanowire

Gaorong Han

2008-01-01

Abstract:By using Fe(NO3)3·9H2O as the starting materials,caustic potash as the mineralizer,α-FeOOH nanowires were prepared by hydrothermal method.The phase and micro-morphology of the products were characterized by X-ray diffraction (XRD),transmission electron microscopy(TEM) and selected area electron diffraction(SAED).The effects of mineralizer concentration and reaction temperature on the phase formation and morphology were investigated.Results indicated that αFeOOH nanowires with orthorhombic structure could be successfully synthesized via hydrothermal processing with 0.1 mol/L KOH at 100 ℃ for 6 h.With the increase of mineralizer concentration,α-FeOOH phase decreases and hexagonal α-Fe2O3 phase appears.When mineralizer concentration is 2.0 mol/L,no crystal phase is obtained.There is no effect of mineralizer concentration on the crystal structure of products at low temperature(40 ℃),for only amorphous phase is obtained under various concentration.At high temperature(200 ℃),α-FeOOH phase can be converted into hexagonal α-Fe2O3 phase rapidly and the size of α-Fe2O3 becomes larger with the increase of mineralizer concentration.
Synthesis and phase formation mechanism of alpha-Fe2O3 powders by hydrothermal reaction method

Ou Ping,Xu Gang,Ni Lihong,Han Gaorong

DOI: https://doi.org/10.3321/j.issn:1002-185X.2008.z2.120

2008-01-01

Rare Metal Materials and Engineering

Abstract:alpha-Fe2O3 was synthesized by hydrothermal reaction method using Fe(NO3)(3)center dot 9H(2)O as starting materials and caustic potash as mineralizer. The powders were characterized by XRD, TEM and SEDA for investigating the effects of reaction time on phase formation and morphology. The results show that alpha-FeOOH nanowires were formed firstly under high temperature and high-pressure conditions, and then the particle-like alpha-Fe2O3 powders were obtained because of the dehydration of alpha-FeOOH as the hydrothermal reaction time increasing. The phase formation mechanism of alpha-Fe2O3 from alpha-FeOOH was discussed in this paper.
Selective Synthesis of Fe 2 O 3 and Fe 3 O 4 Nanowires Via a Single Precursor: A General Method for Metal Oxide Nanowires

Ning Du,Yanfang Xu,Hui Zhang,Chuanxin Zhai,Deren Yang

DOI: https://doi.org/10.1007/s11671-010-9641-y

2010-01-01

Nanoscale Research Letters

Abstract:Hematite (α-Fe2O3) and magnetite (Fe3O4) nanowires with the diameter of about 100 nm and the length of tens of micrometers have been selectively synthesized by a microemulsion-based method in combination of the calcinations under different atmosphere. The effects of the precursors, annealing temperature, and atmosphere on the morphology and the structure of the products have been investigated. Moreover, Co3O4 nanowires have been fabricated to confirm the versatility of the method for metal oxide nanowires.
The preparation of Fe3+ ion-exchanged mesopore containing ZSM-5 molecular sieves and its high catalytic activity in the hydroxylation of phenol

Yu Shen,Fumin Wang,Wei Liu,Xubin Zhang

DOI: https://doi.org/10.1007/s10934-018-0572-9

2018-02-03

Journal of Porous Materials

Abstract:A series of Fe3+ containing catalysts were synthesized using ion-exchange technique over hierarchically porous ZSM-5 (M-ZSM-5) and micro-mesoporous composite ZSM-5/MCM-41 (ZSM-5/MCM-41), respectively. The prepared catalysts were characterized by X-ray diffraction, scanning electron microscope, transmission electron microscope, N2 adsorption–desorption, UV–Vis spectroscopy, temperature programmed reduction and inductively coupled plasma-optical emission spectroscopy. The characterization results exhibit that the hierarchically porous ZSM-5 was synthesized with intracrystalline mesopores, while the micro-mesoporous composite ZSM-5/MCM-41 was prepared with the well-ordered mesopores. Furthermore, the results also prove that the existence of iron in the catalysts was mainly presented in the form of Fe3+ ions. Catalytic performances of the samples for phenol hydroxylation were compared by using H2O2 as oxidant. Under the optimized conditions, Fe3+ ion-exchanged M-ZSM-5 (Fe-M-ZSM-5) shows that a phenol conversion of 42.3% obtained with 92.5% selectivity to dihydroxybenzenes, whereas Fe3+ ion-exchanged ZSM-5/MCM-41 (Fe-ZSM-5/MCM-41) give 46.2% phenol conversion and 90.1% dihydroxybenzenes selectivity, which are all better than most reported results. The recyclability tests show that Fe-ZSM-5/MCM-41 with ordered mesoporous structure and bigger surface area has better anti-deactivation performance than Fe-M-ZSM-5. The excellent catalytic performances were due to the improved diffusion performance with newly created mesopores and the highly active Fe3+ species obtained by ion-exchange technique.

materials science, multidisciplinary,chemistry, physical, applied
Synthesis of α-Fe2O3/TiO2 nanotube arrays for photoelectro-Fenton degradation of phenol

Yanqing Cong,Zhe Li,Yi Zhang,Qi Wang,Qian Xu

DOI: https://doi.org/10.1016/j.cej.2012.03.031

IF: 15.1

2012-01-01

Chemical Engineering Journal

Abstract:Developing new nanophotocatalysts and identifying their roles are highly attractive in environmental protection and energy utilization. Photoelectro-Fenton process is an environmentally friendly technology and has a wide application in the control of environmental pollutants. However, efficient nanophotocatalysts responsive to visible light are still few. In this work, we have successfully synthesized a uniformly dispersed α-Fe2O3/TiO2 nanotubes hetero-nanostructure by electrochemical deposition method for the degradation of phenol. Compared with the separate α-Fe2O3 nanoparticles and TiO2 nanotubes, the composite α-Fe2O3/TiO2 nanotubes electrodes were more effective in the photoelectro-Fenton degradation of phenol and a 100% removal efficiency of phenol was obtained after 60min treatment. The composite α-Fe2O3/TiO2 electrodes showed an enhanced absorbance in visible light region and had good stability to photoelectro-Fenton reactions. The role of α-Fe2O3 nanoparticles in various Fenton-related processes were systematically investigated. The results indicate that α-Fe2O3/TiO2 nanotubes are promising material for pollution prevention.
Synthesis, Characterization and Catalytic Performance for Phenol Hydroxylation of Fe-MCM41 with High Iron Content

Cheng Wu,Yan Kong,Fei Gao,Yong Wu,Yinong Lu,Jun Wang,Lin Dong

DOI: https://doi.org/10.1016/j.micromeso.2007.11.013

IF: 5.876

2007-01-01

Microporous and Mesoporous Materials

Abstract:A series of Fe-MCM41s with different iron content have been synthesized and characterized by XRD, BET, HRTEM, FT-IR, UV–vis and ICP techniques. Their catalytic performances for the direct hydroxylation of phenol were also studied. Results indicated that the mesoporous structure did not collapse until the Fe/Si molar ratio reached up to 0.20. The iron species were mainly in the framework with isolated tetrahedral coordination as Fe/Si molar ratio was smaller than 0.091 and micro-crystals of Fe2O3 were detected when iron content increased further. The prepared samples exhibited excellent catalytic activities for the direct hydroxylation of phenol by hydrogen peroxide at room temperature, which increased with iron content in the framework of MCM41 and did not decline after being recycled 6 times. As Fe/Si molar ratio increased to more than 0.091, the catalytic activity decreased gradually with iron content due to the covering of some active sites, i.e., the incorporated iron species with tetrahedral coordination, by the accumulated Fe2O3 on the surface of the catalyst.
α-Fe2O3 nanosheets as Electro-Fenton catalyst for highly efficient phenol degradation

Yunli Zhai,Xiaodan Chen,Ran Chen,Yuzeng Zhao,Honghua Ge

DOI: https://doi.org/10.1016/j.inoche.2024.112183

IF: 3.428

2024-02-01

Inorganic Chemistry Communications

Abstract:A two-dimensional material, α-Fe2O3 nanosheets, was prepared and used as heterogeneous Electro-Fenton catalysts in phenol degradation. The morphology and electrochemical characterization of the catalysts were carried out. Morphological and structural analysis showed that the prepared product was a hexagonal α-Fe2O3 nanosheet with, a thickness of about 10 nm, and a width of 200 nm. Electrochemical tests show that the catalysts have good catalytic performance. The electrochemical test results of α-Fe2O3 with different morphologies show that the two-dimensional nanosheet morphology improves the catalytic performance of α-Fe2O3. The effects of different factors (current density, aeration rate, pH, catalyst dosage, and electrolyte concentration) were discussed. Free radical quenching experiments demonstrated that OH and SO4 − are the main active species. Furthermore, the catalyst was recycled 7 times, and the phenol removal rate did not decrease significantly.

chemistry, inorganic & nuclear
Catalytic Ozonation Degradation of Phenol in Water by Mesoporous alpha-FeOOH

Dong Yu-Ming,Jiang Ping-Ping,Zhang Ai-Min

2009-01-01

Chinese journal of inorganic chemistry

Abstract:Using FeSO4 center dot 7H(2)O and H2O2 as raw materials, alpha-FeOOH nano-catalyst with larger surface area was prepared by a facile and green hydrothermal synthesis route. The material was characterized by XRD, TEM and N-2 adsorption-desorption. The mesoporous catalyst is composed of alpha-FeOOH nanorods with diameter of 13 similar to 20 nm, length of 70 similar to 100 nm. The catalyst has a larger Brunauer-Emmett-Teller(BET) surface area of 132 m(2). g(-1) and higher density of surface hydroxyl groups of 5.484 mmol . g(-1). The nano-catalyst exhibited excellent catalytic performance in the ozonation degradation of phenol in water. The mechanism Study revealed that the transformation from ozone molecules to hydroxyl radicals and the acceleration on ozonation degradation of phenol were enhanced by the nanocatalyst with higher specific surface area, surface hydroxyl groups and proper pH(pzc) value during the heterogeneous catalysis process.
Enhanced Catalytic Activity of Α-Fe2o3 Nanorods Enclosed with {110} and {001} Planes for Methane Combustion and CO Oxidation

Qi-Xiu Gao,Xiao-Fang Wang,Jie-Ling Di,Xing-Cai Wu,You-Rong Tao

DOI: https://doi.org/10.1039/c1cy00080b

IF: 6.177

2011-01-01

Catalysis Science & Technology

Abstract:Hematite (alpha-Fe2O3) nanorods, nanotubes, and nanocubes were selectively synthesized via a hydrothermal process and subsequent calcination treatment. The nanorods showed higher catalytic activity than the nanotubes and the nanocubes for methane combustion and CO oxidation. It may be attributed to the highest occupancy of iron ions on the surface of the nanorods.
Synthesis of Fe2O3 nanowires by oxidation of iron

Yunyi Fu,Jing Chen,Han Zhang

DOI: https://doi.org/10.1016/S0009-2614(01)01352-5

IF: 2.719

2001-01-01

Chemical Physics Letters

Abstract:By carefully controlling the reacting conditions, including atmosphere, temperature, and reacting time, we managed to prepare the nanowires of Fe2O3 by oxygenating pure iron. X-ray and transmission electronic microscope analyses demonstrate that the Fe2O3 nanowires are of rhombohedral structure, i.e., α-Fe2O3. It is shown by our study that the α-Fe2O3 nanowires have a diameter ranging from 15 to 75 nm and their typical lengths are in the range 10–20 μm. Within our knowledge it is the first report on nanowires of Fe2O3. The Fe2O3 nanowires are expected to present special magnetic, optical and electrical properties, and facilitate future nanoscale device applications.
Formation of α-Fe2O3/FeOOH nanostructures with various morphologies by a hydrothermal route and their photocatalytic properties

Limin Song,Shujuan Zhang

DOI: https://doi.org/10.1016/j.colsurfa.2009.07.022

2009-01-01

Abstract:A series of α-Fe2O3/FeOOH nanostructures with different morphologies have successfully been synthesized based on K4[Fe(CN)6] at 140°C by a novel hydrothermal method. The morphology and phase of α-Fe2O3/FeOOH can be controlled by adjusting the reaction time. UV–vis absorption spectrum, X-ray powder diffraction, and transmission electron microscopy analyses were used to characterize the resulting products. A detailed, rational mechanism is proposed for the formation of α-Fe2O3/FeOOH nanostructures. The potential applications of the as-synthesized α-Fe2O3/FeOOH nanoparticles with different morphologies on photocatalytic decomposition of salicylic acid were also investigated.
Fabrication of Α-Fe<sub>2</sub>o<sub>3</sub> Nanowires by Thermal Oxidation Method

Ling Li,Hai Wang,Hong Jiang

DOI: https://doi.org/10.4028/www.scientific.net/msf.694.79

2011-01-01

Materials Science Forum

Abstract:A large area of hematite (α-Fe 2 O 3 ) nanowires has been successfully synthesized by thermal oxidation of iron foil in an atmosphere environment. The effects on the growth of nanowires have been systematically studied by adjusting the oxidizing environment as well as the reacting temperature and annealing time. The samples were characterized by scanning electron microscope (SEM), x-ray diffraction (XRD) and micro-Raman spectroscopy. Optimum condition was obtained by annealing sample at 600°C for four hours in oxygen-poor environment. Nanowires with dense, high aspect ratio and sharp tips were observed. The average diameter and length of the nanowires was 80 nm and 5μm, respectively.
Synthesis and Characterization of Fe−Fe2O3 Core−Shell Nanowires and Nanonecklaces

Lirong Lu,Zhihui Ai,Jinpo Li,Zhi Zheng,Quan Li,Lizhi Zhang

DOI: https://doi.org/10.1021/cg060633a

IF: 4.01

2007-01-01

Crystal Growth & Design

Abstract:Fe-Fe2O3 core-shell nanowires and nanonecklaces were obtained simply through controlling the reduction rate of Fe3+ ions by sodium borohydride in aqueous solution at ambient atmosphere. The resulting materials were characterized by X-ray powder diffraction, scanning electron microscopy images and energy dispersive X-ray spectrum, transmission electron microscopy, elemental mapping, X-ray photoemission spectroscopy, and magnetization measurements. A possible formation mechanism was proposed on the basis of characterization results. It was interesting to find that the core-shell nanowires used in electrochemical-assisted and ultrasound-assisted Fenton-like reaction systems could much more efficiently degrade organic pollutant in aqueous solutions than traditional Fenton reagent Fe2+ ions under neutral pH and pH 2, respectively. This study indicates that the resulting iron-containing nanostructures are promising materials in magnetic, environmental, and catalytic fields.
Hydrothermal synthesis of monodisperse α-Fe2O3 nanocubes

jia liu,jinrui wang,yq li,peifa jia,f lu,kwangcheng chen

DOI: https://doi.org/10.1179/1432891714Z.0000000001112

2015-01-01

Materials Research Innovations

Abstract:Monodisperse alpha-Fe2O3 nanocubes with a mean size of 70 nm have been successfully synthesised by a hydrothermal process using Fe(NO3)(3) and NaOH as raw materials. The morphology and nanostructure of products were characterised by X-ray diffraction, transmission electron microscopy and field-emission scanning electron microscopy. The results revealed that reaction temperature had a remarkable effect on the morphology of the alpha-Fe2O3 nanoparticles. Furthermore, alpha-FeOOH was generated as the intermediate during the hydrothermal dehydration reaction and the nanocrystals experienced a complex time-dependent evolution. For the hydrothermal synthesis of alpha-Fe2O3 nanocubes, the optimum temperature and reaction time were 180 degrees C and 6 hours, respectively. In addition, the products obtained rapid purification via a heat treatment at 600 degrees C for 1 hour.
Synthesis and Catalytic Activity of Fe-MCM-41 Nanoparticles

hong liang zhang,c j tang,fei gao,lin dong

DOI: https://doi.org/10.4028/www.scientific.net/AMR.933.17

2014-01-01

Advanced Materials Research

Abstract:Mesostructured Fe-MCM-41 nanoparticles have been hydrothermally prepared for the first time with assistance of binary surfactants (CTAB and F127). The formation of nanoparticles consists of two steps, that is, the hydrolysis of silica precursor via catalysis by an acidic ferric salt, followed by facile assembly into mesostructured nanocomposites with cationic micelles by addition of condensation catalyst. In the hydroxylation of phenol with aqueous H2O2, Fe-MCM-41-NP displayed higher activity than a Fe-MCM-41 sample with normal particle size (Fe-MCM-41-LP).
Synthesis of Framework-Substituted Fe-Hms and Its Catalytic Performance for Phenol Hydroxylation

H Liu,GZ Lu,YL Guo,Y Guo,JS Wang

DOI: https://doi.org/10.1088/0957-4484/17/4/026

IF: 3.5

2006-01-01

Nanotechnology

Abstract:The iron-incorporated mesoporous silica material Fe-HMS was successfully synthesized at ambient temperature by using dodecylamine as the template agent, and it was characterized by XRD, SEM, FT-IR, UV-vis, ESR and N-2 adsorption measurements. Its catalytic performance was studied for phenol hydroxylation with H2O2 in a fixed-bed reactor. The results show that Fe3+ ions have been successfully incorporated into the framework of HMS, and Fe-HMS has a uniform mesoporous structure with about 2.7 nm pore diameter. After Fe-HMS is calcined, most of the Fe3+ ions remain in the tetrahedral coordinated framework, and only a small part of Fe species migrate to the extraframework. Fe-HMS has high catalytic activity and very high selectivity to dihydroxybenzene for the hydroxylation of phenol. Over the Fe-HMS catalyst, the product distribution of phenol hydroxylation is different from that over the microporous TS-1 zeolite. The solvents have great influence on the catalytic activity of Fe-HMS, and water is the best solvent.

Α-Fe2o3 Nanowires. Confined Synthesis and Catalytic Hydroxylation of Phenol

Hydrothermal Synthesis and Characterization of Uniform Α-Feooh Nanowires in High Yield

Hydrothermal Conversion of Fe2o3/Sio2 Spheres into Fe2o3/Silicalite-1 Nanowires: Synthesis, Characterization, and Catalytic Properties

Fe2O3/SiO2 Nanowires Formed by Hydrothermally Transforming SiO2 Spheres in the Presence of Fe3+: Synthesis, Characterization, and Catalytic Properties

Preparation and Catalytic Property of Single Crystal Multiporousα-Fe_2O_3 Nanorods

Effects of KOH and Temperature on Hydrothermal Synthesis of Α-Feooh Nanowire

Synthesis and phase formation mechanism of alpha-Fe2O3 powders by hydrothermal reaction method

Selective Synthesis of Fe 2 O 3 and Fe 3 O 4 Nanowires Via a Single Precursor: A General Method for Metal Oxide Nanowires

The preparation of Fe3+ ion-exchanged mesopore containing ZSM-5 molecular sieves and its high catalytic activity in the hydroxylation of phenol

Synthesis of α-Fe2O3/TiO2 nanotube arrays for photoelectro-Fenton degradation of phenol

Synthesis, Characterization and Catalytic Performance for Phenol Hydroxylation of Fe-MCM41 with High Iron Content

α-Fe2O3 nanosheets as Electro-Fenton catalyst for highly efficient phenol degradation

Catalytic Ozonation Degradation of Phenol in Water by Mesoporous alpha-FeOOH

Enhanced Catalytic Activity of Α-Fe2o3 Nanorods Enclosed with {110} and {001} Planes for Methane Combustion and CO Oxidation

Synthesis of Fe2O3 nanowires by oxidation of iron

Formation of α-Fe2O3/FeOOH nanostructures with various morphologies by a hydrothermal route and their photocatalytic properties

Fabrication of Α-Fe&lt;sub&gt;2&lt;/sub&gt;o&lt;sub&gt;3&lt;/sub&gt; Nanowires by Thermal Oxidation Method

Synthesis and Characterization of Fe−Fe2O3 Core−Shell Nanowires and Nanonecklaces

Hydrothermal synthesis of monodisperse α-Fe2O3 nanocubes

Synthesis and Catalytic Activity of Fe-MCM-41 Nanoparticles

Synthesis of Framework-Substituted Fe-Hms and Its Catalytic Performance for Phenol Hydroxylation

Fabrication of Α-Fe<sub>2</sub>o<sub>3</sub> Nanowires by Thermal Oxidation Method