Synthesis and characterization of scandia ceria stabilized zirconia powders prepared by polymeric precursor method for integration into anode-supported solid oxide fuel cells
Hengyong Tu,Xin Liu,Qingchun Yu
DOI: https://doi.org/10.1016/j.jpowsour.2010.11.108
IF: 9.2
2011-01-01
Journal of Power Sources
Abstract:Scandia ceria stabilized zirconia (10Sc1CeSZ) powders are synthesized by polymeric precursor method for use as the electrolyte of anode-supported solid oxide fuel cell (SOFC). The synthesized powders are characterized in terms of crystalline structure, particle shape and size distribution by X-ray diffraction (XRD), transmission electron microscopy (TEM) and photon correlation spectroscopy (PCS). 10Sc1CeSZ electrolyte films are deposited on green anode substrate by screen-printing method. Effects of 10Sc1CeSZ powder characteristics on sintered films are investigated regarding the integration process for application as the electrolytes in anode-supported SOFCs. It is found that the 10Sc1CeSZ films made from nano-sized powders with average size of 655 nm are very porous with many open pores. In comparison, the 10Sc1CeSZ films made from micron-sized powders with average size of 2.5 μm, which are obtained by calcination of nano-sized powders at higher temperatures, are much denser with a few closed pinholes. The cell performances are 911 mW cm −2 at the current density of 1.25 A cm −2 and 800 °C by application of Ce 0.8 Gd 0.2 O 2 (CGO) barrier layer and La 0.6 Sr 0.4 CoO 3 (LSC) cathode. Keywords Intermediate temperature solid oxide fuel cells Anode-supported Electrolyte Scandia-stabilized zirconia Polymeric precursor method 1 Introduction Solid oxide fuel cells (SOFCs) promise to provide a highly efficient and environmentally friendly method for power generation. Intermediate temperature SOFCs offer important advantages over high temperature SOFCs mainly giving a wider choice of low-cost and high performance materials with a higher stability which will reduce the degradation, increase freedom for structural design, etc. Yttria-stabilized zirconia (YSZ) is the most widely applied electrolyte material for intermediate temperature SOFCs. However, YSZ shows limitations regarding further reduction in the ohmic resistance of the electrolytes. In recent years, scandia stabilized zirconia (ScSZ) materials have attracted significant research attention for the electrolyte application in the intermediate temperature SOFCs due to its much higher ionic conductivity than that of YSZ, the state-of-the-art electrolyte for SOFCs [1] . Co-doping has been proposed with various additional dopants like CeO 2 , Sm 2 O 3 , Yb 2 O 3 and Al 2 O 3 to reduce or prohibit an undesirable phase transition from a high conductive cubic phase to a lower conductive rhombohedral β or tetragonal phase [2–4] . Especially, ZrO 2 co-doped with Sc 2 O 3 and CeO 2 promotes the retention of the cubic phase [5,6] . 10 mol% Sc 2 O 3 –1 mol% CeO 2 –89 mol% ZrO 2 (10Sc1CeSZ) has been adopted as one of the candidate electrolyte materials. For successful integration of 10Sc1CeSZ electrolyte films into anode-supported SOFCs, a major challenge is fabrication of the dense electrolyte films onto porous anode substrates. Screen-printing is a widely adopted method to fabricate electrolyte films, which is cost effective and suitable for mass production. A dense and almost pore-free YSZ film can be achieved on the Ni/YSZ cermet substrate after sintering [6] . It was reported that the characteristics of YSZ powders has a significant effect on the formation of dense YSZ films on anode substrates for the development of intermediate temperature SOFCs [7,8] . The ScSZ powders were synthesized by several techniques such as solid-state reaction [9] , co-precipitation [10] , sol–gel [11] and glycine nitrate process [12] . Further synthesis technique deserves exploration for production of large quantities of high purity 10Sc1CeSZ powders suitable for fabrication of the electrolyte films in anode-supported SOFCs. In the present study, 10Sc1CeSZ powders were synthesized by polymeric precursor method (Pechini method) [13] . The polymeric precursor method is known to employ complexing of cations in organic media, making use of low cost precursors resulting in a homogeneous ion distribution at molecular level, which facilitates synthesis of the crystallized powder with ultrafine particle size and high purity at low temperature. 10Sc1CeSZ electrolyte films on green anode substrate were deposited by screen-printing method. Effects of 10Sc1CeSZ powder characteristics on sintered films were investigated regarding the integration process for application as the electrolytes in anode-supported SOFCs. 2 Experimental 2.1 Synthesis The starting materials used in the synthesis of 10Sc1CeSZ powders were Sc(NO 3 ) 3 (99.99%), Ce(NO 3 ) 3 ·6H 2 O (AR), Zr(NO 3 ) 4 ·5H 2 O (AR), citric acid (AR) and ethylene glycol (AR), all from Sinopharm Chemical Reagent Co. Ltd, China. The polymeric precursor solution was prepared by adding citric acid and ethylene glycol into the aqueous solution with Sc(NO 3 ) 3 , Ce(NO 3 ) 3 ·6H 2 O and Zr(NO 3 ) 4 ·5H 2 O at room temperature. The molar ratio metal/citric acid/ethylene glycol was chosen as 1/4/16. With continued heating, the solution became more viscous and a gel was formed. The gel was dried at 200 °C in air during a night and solidified into dark-brown glassy resin. Charring the resin at 400 °C for 2 h resulted in a dark-brown solid mass. The powder obtained at this stage is referred to as “precursor powder”. The powders were heat-treated at 700 °C for 6 h in air. Some of the nano-sized 10Sc1CeSZ powders were calcined at 1000–1400 °C in order to obtain micro-sized powders. The calcined 10Sc1CeSZ powders were subject to ball milling in ethanol for 24 h using zirconia balls. Similarly, Ce 0.8 Gd 0.2 O 2 (CGO) powders were synthesized from polymeric precursor solution using Ce(NO 3 ) 3 ·6H 2 O (AR), Gd(NO 3 ) 3 ·6H 2 O (AR), citric acid (AR) and ethylene glycol (AR) as the starting materials, all from Sinopharm Chemical Reagent Co. Ltd, China. The powders were heat-treated at 700 °C for 6 h in air. La 0.6 Sr 0.4 Co 0.2 Fe 0.8 O 3 (LSCF) and La 0.6 Sr 0.4 CoO 3 (LSC) were prepared by a glycine nitrate process (GNP) process [14] . 2.2 Characterization Thermogravimetric analysis (TGA) was done in a TA Instruments at a heating rate of 10 °C min −1 in air flow. The resultant phases were analyzed by X-ray powder diffraction (XRD) using Cu Kα radiation and a graphite monochromator (40 kV, 40 mA) (Model MXP, MAC, Japan). The mean crystallite size was calculated with the Scherrer equation. The morphology of powders was evaluated using transmission electron microscopy (TEM, JEM-2010). Particle size distributions were measured using photon correlation spectroscopy (PCS, Zetasizer Nano S). The microstructure was observed using field emission scanning electron microscopy (FE-SEM, Hitachi 6300). 2.3 Fabrication The anode-supported cells adopt the standard NiO/YSZ as anode substrate, NiO/10Sc1CeSZ as anode function layer, 10Sc1CeSZ as electrolyte, CGO as barrier layer and LSCF/CGO or LSC as cathode. Planar NiO/YSZ anode supports were fabricated by tape casting. The starting materials of the anode supports were composed of NiO (Nickelous Oxide Green, Sinopharm Chemical Reagent Co. Ltd, China), YSZ (TZ-8YS, Tosoh Co., Japan) with a weight ratio of 60/40. 20 wt% of cornstarch powders were added as pore former. The NiO, YSZ and cornstarch powders were mixed with the solvents (ethanol and butanone), dispersants (triethyl phosphate), binders (polyvinyl butyral) and plasticizers (polyethylene glycol and dibutyl phthalate) by a ball milling process for 24 h. The slurry was cast on a moving PET film using a tape-casting machine after deair. After tape-casting and evaporation of the dispersion aid, the resulting green tape was cut in the appropriate dimension. The NiO/10Sc1CeSZ anode function layer was deposited on the surface of the green anode support by screen printing. Subsequently, the 10Sc1CeSZ electrolyte films from nano-sized or micron-sized powders were applied by screen printing. Half cells were then co-sintered at 1450 °C for 4 h in air. The CGO barrier layers were applied on 10Sc1CeSZ by screen printing. Sintering of the barrier layers was carried out at 1300 °C in air for 1 h. Finally, the cathode films of LSCF/CGO or LSC were applied on the barrier layers by screen printing and sintered at 950 – 1000 °C in air for 2 h. Cornstarch was used as pore former in the cathode formulation. The single cells have the approximate size of 5 cm × 5 cm. The cathode has the dimension of 3.2 cm × 3.2 cm. 2.4 Performance testing The cell performances were evaluated with a fuel cell test station (SF10, Lixin, Wuhan, China). Nickel (Ni) and platinum (Pt) meshes were used for current collection on anode and cathode sides, respectively. The single cells were sealed with a silver paste. A weight of 7 kg was placed on top of the cell housing for a better contact between the current collectors and the electrodes. The gas flows to the anode and the cathode were controlled by digital mass flow controllers. The anode side was flushed with humidified (3% H 2 O) hydrogen with a flow rate of 1000 ml min −1 . On the cathode side, air was supplied as oxidant with a flow rate of 2000 ml min −1 . The current density and voltage values were recorded as a function of operating temperatures in the range 600–800 °C. Before testing, the cell was operated at the voltage of 0.75 V for 3 h. 3 Results and discussion The thermogravimetric analysis from room temperature to 900 °C was performed in order to determine the appropriate heat treatment condition of the 10Sc1CeSZ precursor powders. As shown in Fig. 1 , there are two main weight loss phases in the whole temperature range. The first weight loss related to water appears at 100 °C. The pyrolysis of organic materials occurs at temperatures between 300 and 520 °C. After that, no weight loss can be detected because the decomposition of organic material has finished. Taking into account these results and complete formation of pure phase cubic fluorite structure, the 10Sc1CeSZ precursor powders were calcined at 700 °C. As shown in Fig. 2 , XRD analysis of the calcined 10Sc1CeSZ powders revealed the peaks expected from the cubic phase without any other phases, which indicated that 10Sc1CeSZ powders could be successfully synthesized by the polymeric precursor method. Fig. 2 shows XRD patterns of 10Sc1CeSZ powders after calcination of the as-synthesized powders at different temperatures. The high temperature cubic phase of 10Sc1CeSZ could be stabilized to that of room temperature, and no trace of rhombohedral-ZrO 2 phase could be detected. Therefore, inhibition of cubic–rhombohedral phase transformation assures integration process of 10Sc1CeSZ electrolytes into anode-supported SOFCs. The line broadening in the X-ray diffraction peaks of the as-synthesized 10Sc1CeSZ powders clearly indicates the formation of nano-crystallites. Based on the Scherrer equation, the mean crystallite size was calculated to be about 18.6 nm using the (1 1 1) reflection. In addition, the narrowing of the diffraction peak width with increasing calcination temperature shows that the crystallite size of the nanocrystals increases prominently with the temperature. The peaks gradually sharpen with increasing calcination temperature, which indicates an increase of crystallinity. TEM analyses of as-synthesized powders were performed. As an example, Fig. 3 shows the TEM micrograph of 10Sc1CeSZ powders calcined at 700 °C. It was observed that the nanoparticles are tightly agglomerated and size of the nanoparticles is around 20 nm, which corroborates well with the X-ray line broadening studies. TEM analyses indicate that a particle is an agglomerate of primary particles that are single crystallites. In an agglomerate, the primary particles are bonded together by forming necks at the active contact points [15] . Measurements by photon correlation spectroscopy (PCS) indicated a narrow size distribution of the agglomerated particles, as shown in Fig. 4 . The average particle size is about 655 nm. Gas-tight electrolyte films to separate air and fuel gas are expected for successful integration of 10Sc1CeSZ powders prepared by polymeric precursor method into anode-supported SOFCs. Preparation of dense electrolyte films on porous electrodes is an important step in the fabrication of high-performance SOFCs. For the investigation of the co-sintering behaviors of the 10Sc1CeSZ electrolyte film, NiO/10Sc1CeSZ film and 10Sc1CeSZ film were screen-printed on the surface of green NiO/YSZ support in succession. After printing, the three green layers were dried and co-sintered at 1450 °C for 4 h. The sintered half cells exhibited good flatness, and the films attached well to the substrate. It was found that the nano-sized powders calcined at 700 °C only allowed a lower solid loading for a printable paste, which resulted in the low green density of the deposited 10Sc1CeSZ film. According to Shi [16] , if the green density of ceramics is lower than a critical value, namely, ∼33%, it is difficult to reach full densification under pressureless solid-state sintering conditions due to the existence of thermodynamically stable large pores. On co-sintering of the 10Sc1CeSZ electrolyte film made of nano-sized powders, NiO/10Sc1CeSZ film and the anode support, the low green density of the 10Sc1CeSZ film would make the densification of the electrolyte film difficult despite the high sintering temperature of 1450 °C. Micrographs of the surface and cross-section of the 10Sc1CeSZ electrolyte films made of nano-sized powders are shown in Fig. 5 a and c . The 10Sc1CeSZ film prepared from nano-sized powders is very porous with many open pores in the surface and in the cross-section of films. Thus higher green density of the 10Sc1CeSZ film was expected using micro-sized 10Sc1CeSZ powders for screen printing process. As shown in Fig. 2 , the crystallite sizes apparently increase after calcination in the temperature range of 1000–1400 °C. Micro-sized 10Sc1CeSZ powders with average particle size of 2.5 μm from PCS measurement were obtained just through calcination of nano-sized powders at 1000 °C for 4 h. In comparison, the micro-sized powders allowed a higher solid loading than the nano-sized powders while still obtaining a printable paste. Easier densification of the 10Sc1CeSZ film made of micro-sized powders would be expected during the same co-sintering process. Micrographs of the surface and cross-sections of the 10Sc1CeSZ electrolyte films made of micron-sized powders are shown in Fig. 5 b and d. The thickness of both the electrolyte films is ca. 15 μm ( Fig. 5 c and d). In comparison, the 10Sc1CeSZ film made from micron-sized powders is much denser with a few closed pinholes. Furthermore, the 10Sc1CeSZ film from micro-sized powders presents no apparent crack formation after co-sintering with anode substrate and function layer. This result revealed that the characteristics of the starting powders had crucial effect on the densification of the screen-printed 10Sc1CeSZ films during co-sintering. Fig. 6 shows comparison of the open-circuit voltages (OCVs) of anode-supported cells with the 10Sc1CeSZ electrolyte films made of nano-sized and micro-sized powders, respectively. Here the cathode LSCF/CGO was not optimized and used only for OCV measurements. Both cells were tested under the same gas conditions. The OCVs of the cell with the 10Sc1CeSZ electrolyte film made of micron-sized powders were significantly higher than that made of nano-sized powders. For example, the OCV of the former at 800 °C was 1.08 V, while this value was only 0.82 V for the latter. There was a gap of more than 0.22 V between the OCVs of the two cells in the temperature range of 600–800 °C. The lower OCVs of the cell with the 10Sc1CeSZ electrolyte film made of nano-sized powders indicated some cross-over of fuels, which clearly confirmed that the pores in the electrolyte film made of nano-sized powders were penetrated. In comparison, the cells with the 10Sc1CeSZ electrolyte film made of micro-sized powders achieved high OCVs, which confirmed that these 10Sc1CeSZ electrolyte films were sufficiently dense. The performance of the single cell was shown in Fig. 7 . The cell was operated with 97% H 2 + 3% H 2 O gas as a fuel and air as an oxidant gas. It exhibited the OCVs of 1.098 V, 1.115 V and 1.133 V at 800 °C, 700 °C and 600 °C, respectively. Clearly the OCV values revealed that the 10Sc1CeSZ electrolyte films were dense enough to avoid the gas leakage. Nano-sized LSC powders synthesized by GNP were applied as cathode of the single cell. The powders exhibited the BET-specific area of 10.4 m 2 g −1 [14] . CGO films were applied as barrier layers between 10Sc1CeSZ and LSC films in order to prevent formation of an insulating SrZrO 3 . The CGO film was porous after sintering at 1300 °C due to the low sintering activity of CGO, as shown in Fig. 8 . Testing results showed that relatively good performances were obtained. At the current density of 1.25 A cm −2 , the power density of the cell at 800 °C and 700 °C reached 911 mW cm −2 and 729 mW cm −2 , respectively. In comparison, the power density at 600 °C reduced significantly and reached only 161 mW cm −2 at the current density of 0.5 A cm −2 . These results suggest that low sintering temperature of LSC can prevent SrZrO 3 formation although GCO barrier layer exhibited porous structure. At the same time, the growth in particles size of LSC powders can be inhibited at low sintering temperature, leading to more triple phase boundary points. 4 Conclusion Applicability of the polymeric precursor method has been demonstrated for production of nano-sized 10Sc1CeSZ powders. Micro-sized 10Sc1CeSZ powders can be obtained just through calcination of the nano-sized powders at 1000 °C. Dense 10Sc1CeSZ films made of micro-sized powders were successfully obtained by screen-printing process and co-sintering with green anode support and functional layer. In comparison, the 10Sc1CeSZ film prepared from nano-sized powders exhibited penetrated porous microstructure. The result indicated that the characteristics of the starting powders had crucial effect on the densification of the screen-printed 10Sc1CeSZ films during co-sintering. The power density of 911 mW cm −2 (at the current density of 1.25 A cm −2 , at 800 °C) was achieved in combination with CGO barrier film and LSC cathode. Combination of polymeric precursor method with screen printing technology provides a simple and cost-effective way to fabricate dense 10Sc1CeSZ electrolyte films on porous anode supports. Acknowledgement This work was financially supported by the European Commission under contract no. SES6-CT-2006-020089 as part of the Integrated Project “SOFC600”. References [1] O. Yamamoto Y. Arati Y. Takeda N. Imanishi Y. Mizutani M. Kawai Y. Nakamura Solid State Ionics 79 1995 137 [2] Y. Arachi T. Asai O. Yamamoto Y. Takeda N. Imanishi K. Kawate C. Tamakoshi J. Electrochem. Soc. 148 2001 A520 [3] T. Ishii Solid State Ionics 78 1995 333 [4] K. Ukai Y. Mizutani Y. Kume H. Yokogawa S.C. Singhal Proc. of the 7th Int. Symposium on Solid Oxide Fuel Cells The Electrochem. Soc. Inc., NJ 2001 375 [5] Z. Wang M. Cheng Z. Bia Y. Dong H. Zhang J. Zhang Z. Feng C. Li Mater. Lett. 59 2005 2579 [6] M.A. Laguna-Bercero S.J. Skinner J.A. Kilner J. Power Sources 192 2009 126 [7] Y. Zhang X. Huang Z. Lü X. Ge J. Xu X. Xin X. Sha W. Su Solid State Ionics 177 2006 281 [8] Y. Jun Leng S. Hwa Chan K. Aik Khor S. Ping Jiang P. Cheang J. Power Sources 117 2003 26 [9] R. Ruh H.J. Garrett R.F. Domagala V.A. Patel J. Am. Ceram. Soc. 60 1977 399 [10] S.P.S. Badwal J. Drennan Solid State Ionics 53–56 1992 769 [11] Y. Mizutani M. Tamura M. Kawai O. Yamamoto Solid State Ionics 72 1994 271 [12] D. Lee I. Lee Y. Jeon R. Song Solid State Ionics 176 2005 1021 [13] M.P. Pechini, U.S. Patent 3,330,697 (1967). [14] H.-x. Wang H.-y. Tu J.Funct. Mater. 41 3 2010 397 [15] R.K. Lenka T. Mahata P.K. Sinha B.P. Sharma J. Am. Ceram. Soc. 89 2006 3871 [16] J.L. Shi J. Mater. Res. 14 1999 1398
What problem does this paper attempt to address?
-
A simple and easy one-step fabrication of thin BaZr0.1Ce0.7Y0.2O3−δ electrolyte membrane for solid oxide fuel cells
Kui Xie,Ruiqiang Yan,Yinzhu Jiang,Xingqin Liu,Guangyao Meng
DOI: https://doi.org/10.1016/j.memsci.2008.07.055
IF: 9.5
2008-01-01
Journal of Membrane Science
Abstract:A green BaZr0.1Ce0.7Y0.2O3−δ (BZCY) electrolyte layer was deposited on porous anode substrate (BZCY:NiO=35:65, in weight ratio) by a suspension spray. In this process, the suspension was prepared by directly ball-milling the mixed BaCO3, CeO2, ZrO2 and Y2O3 powders in ethanol for 24h. Then the bi-layers were co-sintered at 1400°C for 5h in air to obtain dense and uniform electrolyte membrane in the thickness of 10μm. With Nd0.7Sr0.3MnO3−δ cathode, a fuel cell was assembled. It was tested from 600°C to 700°C using humid hydrogen as fuel and air as oxidant. The cell at 700°C exhibited 1.02V for open circuit voltage (OCV), 450mW/cm2 for peak output and 0.18Ωcm2 for electrode polarizations under open circuit conditions, respectively. The results indicate that it is feasible to fabricate thin electrolyte membrane for solid oxide fuel cells (SOFCs) by this simple, cost-effective and efficient technique.
-
YSZ Thin Films Prepared by a Novel Powder Coating Process on Porous NiO-YSZ Cermet
Wei Tao Bao,Yin Zhu Jiang,Guang Yan Zhu,Jian Feng Gao,Guang Yao Meng
DOI: https://doi.org/10.4028/www.scientific.net/KEM.280-283.435
2007-01-01
Key Engineering Materials
Abstract:Dense YSZ thin film with a thickness from 2 to 15 mum on porous Ni-YSZ anode support was fabricated by a novel powder coating process. The performance of the cell with a composite of Sm0.8SrCoO3- YSZ (40 wt.%) as cathode was examined over a temperature range from 550 to 800 degreesC, using H-2 -3% H2O as fuel and air as oxidant. The maximum power density of the cells was over 300 mW/cm(2) at 800degreesC. The open circuit voltage of the cells reached 1.1 V at 750 degreesC, illustrating the full dense of the YSZ electrolyte. The anode-electrolyte interfacial resistances were negligible in comparison with that of cathode-electrolyte, indicating the good coherency of the YSZ electrolyte to the anode support. These results demonstrate the reliability of this novel process for thin electrolyte SOFCs.
-
Anode Performance of Mn-doped Ceria–scsz for Solid Oxide Fuel Cell
Guoqiang Cai,Renzhu Liu,Chunhua Zhao,Junliang Li,Shaorong Wang,Tinglian Wen
DOI: https://doi.org/10.1007/s10008-010-1079-8
IF: 2.747
2010-01-01
Journal of Solid State Electrochemistry
Abstract:The 70 wt.% Mn-doped CeO2 (MDC)-30 wt.% Scandia-stabilized zirconia (ScSZ) composites are evaluated as anode materials for solid oxide fuel cells (SOFCs) in terms of chemical compatibility, thermal expansion coefficient, electrical conductivity, and fuel cell performance in H2 and CH4. The conductivity of MDC10 (10 mol.% Mn-doping), MDC20, and CeO2 are 4.12, 2.70, and 1.94 S cm−1 in H2 at 900 °C. With 10 mol.% Mn-doping, the fuel cells performances improve from 166 to 318 mW cm−2 in H2 at 900 °C. The cell with MDC10–ScSZ anode exhibits a better performance than the one with MDC20–ScSZ in CH4, the maximum power density increases from 179 to 262 mW cm−2. Electrochemical impedance spectra indicate that the Mn doping into CeO2 can reduce the ohmic and polarization resistance, thus leading to a higher performance. The results demonstrate the potential ability of MDC10–ScSZ composite to be used as SOFCs anode.
-
Anode-supported ScSZ-electrolyte SOFC with whole cell materials from combined EDTA–citrate complexing synthesis process
Hongxia Gu,Ran Ran,Wei Zhou,Zongping Shao
DOI: https://doi.org/10.1016/j.jpowsour.2007.07.056
IF: 9.2
2007-01-01
Journal of Power Sources
Abstract:The potential application of combined EDTA–citrate complexing process (ECCP) in intermediate-temperature solid-oxide fuel cells (IT-SOFCs) processing was investigated. ECCP-derived scandia-stabilized-zirconia (ScSZ) powder displayed low packing density, high surface area and nano-crystalline, which was ideal material for thin-film electrolyte fabrication based on dual dry pressing. A co-synthesis of NiO+ScSZ anode based on ECCP was developed, which showed reduced NiO(Ni) and ScSZ grain sizes and improved homogeneity of the particle size distribution, as compared with the mechanically mixed NiO+ScSZ anode. Anode-supported ScSZ electrolyte fuel cell with the whole cell materials synthesized from ECCP was successfully prepared. The porous anode and cathode exhibited excellent adhesion to the electrolyte layer. Fuel cell with 30μm thick ScSZ electrolyte and La0.8Sr0.2MnO3 cathode showed a promising maximum peak power density of 350mWcm−2 at 800°C.
-
Modified Sol-gel Method used for Obtaining SOFC Electrolyte Materials
Crina Silvia Suciu,Egil Severin Erichsen,Alex C. Hoffmann,Eugen Dorolti,Romulus Tetean
DOI: https://doi.org/10.1149/1.3205706
2009-09-25
ECS Transactions
Abstract:A new modified sol-gel method using sucrose and pectin as organic precursors was used to obtain 7ScSZ and 11ScSZ nanoparticles as electrolyte materials for solid oxide fuel cells (SOFCs). Scandia stabilized zirconia (ScSZ) offers significantly higher conductivity than most other electrolyte materials (e.g. yttria stabilized zirconia, YSZ). The high cost of scandia can be compensated to some degree by the use of thin electrolyte films. Also, it is important to reduce the costs incurred by all the intermediate fabrication steps of SOFCs. The new organic precursors used in the modified sol-gel method have the advantages of being ubiquitous, cheap, easy to handle and store and environmentally friendly. The produced nano-powders were pressed to pellets and sintered in two different ways to obtain different grain sizes. The powders and pellets were investigated using TEM (Transmission Electron Microscopy), XRD (X-ray Diffraction), physical adsorption (BET), and EIS (Electrochemical Impedance Spectroscopy) to determine the morphology, particle size, crystal structure, crystallite size and specific surface area of the powders and the electrical properties of the sintered pellets.
-
Scandia-stabilized Zirconia-Impregnated (la, Sr)MnO 3 Cathode for Tubular Solid Oxide Fuel Cells
Renzhu Liu,Guoqiang Cai,Junliang Li,Chunhua Zhao,Shaorong Wang,Tinglian Wen,Zhaoyin Wen
DOI: https://doi.org/10.1007/s10008-010-1029-5
IF: 2.747
2010-01-01
Journal of Solid State Electrochemistry
Abstract:A LSM-ScSZ composite cathode for anode-supported tubular solid oxide fuel cell (SOFC) has been successfully developed. The fabrication method is a two-step process including dip-coating LSM framework and ion-impregnating ScSZ. A preliminary examination of the single tubular cell, which consists of a Ni-YSZ anode support tube, a Ni-ScSZ anode functional layer, a ScSZ electrolyte film, and the LSM-ScSZ cathode, has been carried out, and an improved performance is obtained. The polarization resistance of the cathode side is significantly decreased by impregnating the electronic conducting phase (LSM) with the ionic conducting phase (ScSZ). And the single cell generates the maximum power density of 433 mW cm-2 at 850 ºC, being operated with humidified hydrogen.
-
Al2O3 Toughening ScSZ Electrolyte Fabricated by Water-Based Tape Casting Technique for Solid Oxide Fuel Cells
Haoran Wang,Ze Lei,Han Zhang,Yongkang Li,Junmeng Jing,Yiqian Jin,Zhibin Yang,Suping Peng
DOI: https://doi.org/10.1115/1.4052313
IF: 2.323
2021-09-24
Journal of Electrochemical Energy Conversion and Storage
Abstract:Abstract A water-based tape-casting slurry is reported to prepare the ceria and scandia co-doped zirconia (ScSZ) electrolyte films. The slurry is characterized and optimized through Zeta potential and rheological property measurements. Smooth and flat ScSZ electrolyte films are obtained by improving the sintering process. The microstructure, electrical performance, and mechanical property of ScSZ with adding different contents of Al2O3 are also investigated. The results show that a proper amount of Al2O3 has a beneficial effect on the densification of ScSZ. A significant decrease in the grain boundary resistance of ScSZ is observed by adding 0.5 wt% Al2O3. The bending strength of the sample with 0.5 wt% Al2O3 (ScSZ-0.5A) is about 400 MPa, which is 20% higher than pure ScSZ. The ScSZ-0.5A electrolyte film fabricated by the water-based tape-casting method shows appropriate electrical conductivity and high mechanical strength, which is promising for practical application in solid oxide fuel cells (SOFCs).
energy & fuels,electrochemistry
-
Optimization of ScSZ/GDC bilayer thin film electrolyte for anodic aluminum oxide supported low temperature solid oxide fuel cells
Gu Young Cho,Yusung Kim,Soon Wook Hong,Wonjong Yu,Young-Beom Kim,Suk Won Cha
DOI: https://doi.org/10.1088/1361-6528/aac132
IF: 3.5
2018-06-13
Nanotechnology
Abstract:Due to the poor chemical stability of CeO2-based materials, doped CeO2 electrolytes are generally used as a stabilized ZrO2 protection layer/doped CeO2 electrolyte bilayer structure. Since the ionic conductivity of stabilized ZrO2 materials is lower than that of doped CeO2 materials, the thickness of the ZrO2 protective layer needs to be optimized. Thus, in this study, nano-porous anodic aluminum oxide template based scandia stabilized zirconia (ScSZ)/gadolinia doped ceria (GDC) bilayer electrolyte low temperature solid oxide fuel cells (LT-SOFCs) are successfully fabricated and investigated. The optimized thickness of the ScSZ protection layer is revealed by physical and electrochemical characterizations to maximize the performance of LT-SOFCs. The 160 nm ScSZ/400 nm GDC bilayer electrolyte LT-SOFC achieves a maximum power density of 252 mW · cm-2 and an open circuit voltage of 1.02 V OCV at 450 °C.
materials science, multidisciplinary,physics, applied,nanoscience & nanotechnology
-
A cathode-supported SOFC with thin Ce0.8Sm0.2O1.9 electrolyte prepared by a suspension spray
Bin Lin,Wenping Sun,Kui Xie,Yingchao Dong,Dehua Dong,Xingqin Liu,Jianfeng Gao,Guangyao Meng
DOI: https://doi.org/10.1016/j.jallcom.2007.10.063
IF: 6.2
2008-01-01
Journal of Alloys and Compounds
Abstract:In order to develop a cost-effective route to fabricate solid oxide fuel cells (SOFCs), a dense Ce0.8Sm0.2O1.9 (SDC) electrolyte was fabricated on a porous cathode based on a mixed conducting La0.8Sr0.2FeO3−δ (LSF) via a suspension spray/co-firing process. For the purpose of shrinkage matching between the cathode support and the electrolyte membrane, nano-SDC1 powder for the easily sinterable electrolyte was synthesized with ammonia as the precipitant from the nitrates, whereas SDC2 powder prepared by modified glycine–nitrate method (GNP) was added into cathode to favor the shrinkage of La0.8Sr0.2FeO3−δ(LSF). Sm-doped ceria solid solution was directly formed during precipitation at 50°C, and this is ascribed to the role of OH−. The powders calcined at 800°C for 2h were still uniform and exhibited an average particle size of 20nm. The bi-layer with 10μm dense SDC electrolyte was obtained by co-sintering at 1250°C for 5h. A thin and well-adherent anode was formed by depositing ultra-fine NiO–SDC powders, followed by sintering at 1000°C. The obtained single cells were tested with humidified (3% H2O) hydrogen as fuel and the static air as oxidant. The maximum power density reached 67.2mW/cm2 at 600°C.
-
Direct synthesis of Ce0.8Sm0.2−xZnxO2−δ electrolyte by sol–gel for IT-SOFC
Yan Liu,Haobiao Qin,Meilin Li,Jinqun Cheng,Chunbao Tang,Jie Xiao,Yongmin Xie
DOI: https://doi.org/10.1007/s11581-022-04677-2
IF: 2.961
2022-09-21
Ionics
Abstract:In this paper, high-quality nanosized Ce 0.8 Sm 0.2− x Zn x O 2− δ ( x = 0, 0.02, 0.04, 0.08, and 0.16) powders are successfully synthesized by sol–gel process for intermediate-temperature solid oxide fuel cell (IT-SOFC) application. The thermal behavior, porosity, crystal phase, surface microstructure, and electrical properties of Ce 0.8 Sm 0.2− x Zn x O 2− δ are studied by thermogravimetric-differential scanning calorimeter (TG-DSC), Archimedes drainage method, X-ray diffraction (XRD), scanning electron microscope (SEM), and electrochemical impedance spectroscopy (EIS), respectively. The results show that Ce 0.8 Sm 0.2− x Zn x O 2− δ electrolyte appears very high sintering activity even at sintering temperature as low as 1300 °C. The crystal phase of sample powders after sintered at 600 °C belongs to single-phase cubic fluorite structure with mean particle size of 15 nm. The lattice parameter increases first until doping 2 mol.% Zn and then decreases with more doping amount. Electrochemical performance results demonstrate that doping with appropriate amount of Zn can significantly improve the conductivity of SDC materials. The highest conductivity of 0.057 S·cm −1 at 800 °C is obtained for Ce 0.8 Sm 0.16 Zn 0.04 O 2− δ , owing to high density, ultrafine grains, and increased grain boundaries. Furthermore, the fuel cell performance of Ce 0.8 Sm 0.16 Zn 0.04 O 2− δ electrolyte is measured with 5 wt.% Fe-loaded activated carbon as the fuel. It delivers an outstanding performance, with an OCV of 1.02 V, a maximum power output of 408 mW·cm −2 at 850 °C, indicating that Ce 0.8 Sm 0.16 Zn 0.04 O 2− δ may have potential application for IT-SOFC electrolyte materials.
chemistry, physical,physics, condensed matter,electrochemistry
-
Preparation of Thin Electrolyte Film Via Dry Pressing/heating/ Quenching/calcining for Electrolyte-Supported SOFCs
Hong Chang,Jing Yan,Huili Chen,Guangming Yang,Jing Shi,Wei Zhou,Fangqin Cheng,Si-Dian Li,Zongping Shao
DOI: https://doi.org/10.1016/j.ceramint.2019.02.026
IF: 5.532
2019-01-01
Ceramics International
Abstract:The development of technologies used to prepare thin electrolyte films will stimulate the application of electrolyte supported SOFCs since thin electrolyte films typically have low ohmic resistances and good electrochemical performance. This paper presents a novel method for the preparation of thin electrolyte films for yttria-stabilized zirconia (YSZ)-supported solid oxide fuel cells (SOFCs) via dry pressing/heating/quenching/calcining. The thicknesses of the as-prepared YSZ films were as low as 78 mu m, which is significantly thinner than those prepared using a traditional method (greater than 200 mu m) via dry pressing/calcining/polishing. More importantly, the preparation process was quicker. Using this novel method, a YSZ-supported cell with a configuration of (La0.6Sr0.4)(0.9)Co0.8Fe0.2O3-delta (LSCF)-Ce0.8Sm0.2O2-delta(SDC)/SDC/YSZ/SDC/Ba0.5Sr0.5Co0.8Fe0.2O3-delta(BSCF)-SDC was fabricated and tested. The results showed promising electrochemical performance and a peak power density of 0.64 W cm(-2) at 850 degrees C was obtained, which was much higher than the cell fabricated using the traditional method (0.29 W cm(-2)). The ohmic resistance (R-O) at 850 degrees C is 0.19 Omega cm(2), which is much lower than that of the cell fabricated using the traditional method (0.33 Omega cm(2)) at an identical temperature. The modified method described in this work is shown to be a promising technique to prepare thin electrolyte films for high-performance, electrolyte-supported SOFCs.
-
Application of 8YSZ Nanopowder Synthesized by the Modified Solvothermal Process for Anode Supported Solid Oxide Fuel Cells
Malinee Meepho,Suthee Wattanasiriwech,Pavadee Angkavatana,Darunee Wattanasiriwech
DOI: https://doi.org/10.1166/jnn.2015.10223
Abstract:Thin electrolyte yttria-stabilized zirconia (8YSZ) films were coated on the porous solid oxide fuel cell (SOFC) anode substrates for the use at an intermediate temperature range. Nano-8YSZ powder with a particle size of about 5 nm was synthesized using the modified solvothermal process. The electrolyte suspension was prepared by dispersion the synthesized 8YSZ nanopowder in ethanol, with PVB and 1,3-propanediol as a binder and a charging agent respectively. The 8YSZ suspension was subsequently deposited on the pre-sintered NiO-YSZ porous substrates by the electrophoretic deposition (EPD) technique. In order to obtain high quality electrolyte films, preparation process was optimized through two strategic approaches; (i) adjustment of suspension's rheological property and (ii) compatibility of anode-electrolyte sintering shrinkage. Rheological property of the suspension was improved with an addition of 1,3-propanediol. The zeta potential of this suspension was increased and reached the value of +24 mV so the well-dispersed slurry was finally obtained. The second approach was achieved by using a proper composite anode powders. Dense and uniform 8YSZ electrolyte films with a thickness of about 1 thickness successfully be formed on the NiO-YSZ porous substrates after co-sintering at 1400 °C for 2 h.
-
La0.4sr0.6co0.2fe0.7nb0.1o3-Delta Electrodes for Ysz-Based Symmetrical Sofc
Niu Yushuang,Yang Zhibin,Zheng Ziwei,Jia Yihai,Han Minfang
2015-01-01
Rare Metal Materials and Engineering
Abstract:La0.4Sr0.6Co0.2Fe0.7Nb0.1O3-delta (LSCFN), a perovskite oxide material, was synthesized by a solid state reaction method. The electrolyte-supported symmetrical solid oxide fuel cells were fabricated by tape-casting and screen-printing procedure using YSZ as electrolyte, Gd0.1Ce0.9O2-delta (GDC) as an interlayer and LSCFN as both anode and cathode. The crystal structure and chemical stability were examined by X-ray diffraction (XRD) and microstructure was inspected by scanning electron microscopy (SEM). The electrical properties of the single cell were tested by humidified (3% H2O) H-2 and (3% H2O) CH4 as fuel, ambient air as oxidant and the stability was tested in humidified (3% H2O) CH4 at 850 degrees C. The results show that LSCFN appears to be chemically compatible with GDC. The maximum power density is 254 and 105 mW/cm(2) in humidified H-2 and CH4 at 850 degrees C, respectively. Stable performance is sustained for 100 h operating in humidified CH4.
-
Fabrication and Characterizations of Ysz Electrolyte Films for Sofc
Min-Fang Han,Zhibin Yang,Ze Liu,Hui-Rong Le
DOI: https://doi.org/10.4028/www.scientific.net/kem.434-435.705
2010-01-01
Key Engineering Materials
Abstract:Yttria stabilized zirconia (YSZ) has been widely used as electrolyte in solid oxide fuel cell (SOFC). The effect of fabrication process on the properties of YSZ electrolyte thick film is discussed in the paper. With YSZ nano-powders of about 20-60nm as raw material, YSZ green adobe was fabricated by tape calendering process. Three-step sintering process was performed firstly holding at 1000°C for 2h, then raising to 1300~1400°C, then decreasing to 1200~1300°C within 30 minutes, and finally calcining at 1200~1300°C for 5~20 hrs. Dense YSZs with relative density of 96-99% are obtained; the grain size of YSZ was reduced to 0.5-3µm. During the process of grain growth, there are both grain boundary diffusion and grain boundary migration. The feasibility of densification without grain growth relies on the suppression of grain boundary migration while keeping grain boundary diffusion active at a temperature as low as 1200~1300°C. Whereas the electric conductivities of the YSZs are even higher than that obtained in conventional single step sintering process. The process is applied to the anode-supported SOFCs co-fired at 1250~1300°C, and the cathode-supported SOFCs co-fired at 1200~1250°C.
-
Boosting intermediate temperature performance of solid oxide fuel cells via a tri‐layer ceria–zirconia–ceria electrolyte
Jun Zhang,Christian Lenser,Niklas Russner,André Weber,Norbert H. Menzler,Olivier Guillon
DOI: https://doi.org/10.1111/jace.18482
IF: 4.186
2022-04-14
Journal of the American Ceramic Society
Abstract:Using cost‐effective fabrication methods to manufacture a high‐performance solid oxide fuel cell (SOFC) is helpful to enhance the commercial viability. Here, we report an anode‐supported SOFC with a three‐layer Gd0.1Ce0.9O1.95(GDC)/Y0.148Zr0.852O1.926 (8YSZ)/GDC electrolyte system. The first dense GDC electrolyte is fabricated by co‐sintering a thin, screen‐printed GDC layer with the anode support (NiO‐8YSZ substrate and NiO‐GDC anode) at 1400°C for 5 h. Subsequently, two electrolyte layers are deposited via physical vapor deposition (PVD). The total electrolyte thickness is less than 5 μm in an area of 5 × 5 cm2, enabling an area‐specific ohmic resistance as low as 0.125 Ω cm2 at 500 °C (under open circuit voltage), and contributing to a power density as high as 1.2 W cm–2 at 650°C (at an operating cell voltage of 0.7 V, using humidified (10 vol.% H2O) H2 as fuel and air as oxidant). This work provides an effective strategy and shows the great potential of using GDC as electrolyte for high‐performance SOFC at intermediate temperature.This article is protected by copyright. All rights reserved
materials science, ceramics
-
Development of yttria-stabilized zirconia thin films via slurry spin coating for intermediate-to-low temperature solid oxide fuel cells
Kongfa Chen,Zhe Lü,Na Ai,Xiqiang Huang,Yaohui Zhang,Xianshuang Xin,Ruibin Zhu,Wenhui Su
DOI: https://doi.org/10.1016/j.jpowsour.2006.01.079
IF: 9.2
2006-09-01
Journal of Power Sources
Abstract:Yttria-stabilized zirconia (YSZ) thin films were successfully fabricated on porous NiO–YSZ anode substrates via a slurry spin coating method. With ∼34-μm-thick Sm0.2Ce0.8O1.9 (SDC)-impregnated La0.7Sr0.3MnO3 (LSM) cathodes, a single cell based on a ∼9-μm-thick YSZ film exhibited a good performance at intermediate-to-low temperature. The cell produced an open-circuit voltage (OCV) of ∼1.08V, and maximum power densities of ∼0.42 and ∼0.70Wcm−2 at 650°C, while the cathode was exposed to the stationary air and blown with 100mLmin−1 oxygen airflow, respectively. Enhanced cell performance with oxygen airflow was attributed to the improved cathode performance. By separating the total voltage drop into ohmic and non-ohmic contributions, it could be concluded that the cell performance was primarily determined by the polarization of the electrodes. It is believed that by optimizing the film fabrication process and improving the cathode performance, intermediate-to-low temperature solid oxide fuel cells (SOFCs) based on supported YSZ electrolyte thin films could be put into practice in not far future.
energy & fuels,materials science, multidisciplinary,electrochemistry,chemistry, physical
-
Five‐layer reverse tape casting of IT‐SOFC
Abigail L. Snowdon,Zeyu Jiang,Robert Steinberger‐Wilckens
DOI: https://doi.org/10.1111/ijac.13911
2021-10-05
International Journal of Applied Ceramic Technology
Abstract:Tape casting is a well-established method for manufacturing thin ceramic layers with controllable thickness and porosity. This study investigates the potential of 10Sc1CeSZ material for the electrolyte and anode layers for intermediate-temperature solid oxide fuel cells (IT-SOFC) in an anode supported cell (ASC) geometry. In order to use La0.6Sr0.4Co0.2Fe0.8 Oxide (LSCF) cathode material, a Gd0.2Ce0.8 Oxide (GDC) barrier layer is needed, however, thermal expansion coefficient (TEC) mismatch results in delamination of the GDC from the electrolyte during high temperature sintering when fabricated by conventional tape casting procedures. For the first time, ASC have been manufactured by a five-layer tape casting technique; barrier layer, novel composite layer, electrolyte, anode functional layer (AFL), and anode substrate (AS). Ni-ScCeSZ composite cells were tested between 650 - 800°C in H2:N2 fuel (85% H2) on the anode and air on the cathode to yield a maximum power density of 0.46 W/cm2. These results demonstrate the feasibility of this new five-layer tape casting technique to produce IT-SOFC.This article is protected by copyright. All rights reserved
materials science, ceramics
-
Fabrication and Performance of Anode-Supported Electrolyte Thin Films SOFCs
Miao Wenting,Han Minfang,Yin Huiyan
DOI: https://doi.org/10.3321/j.issn:1002-185X.2008.z1.112
2008-01-01
Rare Metal Materials and Engineering
Abstract:The development of anode-supported SOFCs is important to increase the lower impedance and higher power density. In this study, YSZ electrolyte film was prepared by screen printing, dip coating and screen printing combined with dip coating, respectively. A three-step sintering process was used to reduce the sintering temperature of the Y(2)O(3) stabilized ZrO(2) (YSZ). The sintering shrinkage of the anode was adjusted by adding different amount of the pore former. The YSZ and the anode substrate was combined readily by co-firing. The anode supporter appear porous. The thickness of the YSZ electrolyte film with anode supporter added with 10% pore former and co-fired at 1300 similar to 1350 degrees C was 20 mu m and the grain size was 0.5 similar to 3 mu m.
-
Scalable and facile fabrication of tri-layer electrolytes by reactive sputtering for efficient and durable solid oxide fuel cells
Fuyuan Liang,Zehua Pan,Haiqing Wang,Zhenjun Jiao,Zilin Yan,Xuesong Shen,Qunhui Yuan,Junwei Wu
DOI: https://doi.org/10.1016/j.cej.2024.149523
IF: 15.1
2024-02-15
Chemical Engineering Journal
Abstract:Scalable and facile fabrication of large-area electrolytes by physical vapor deposition (PVD) for efficient and durable solid oxide fuel cells (SOFCs) is a promising way to tackle the issues such as elemental diffusion and warpage of cells resulted from high-temperature sintering in conventional wet ceramic methods. Herein, high-performance industrial size, 12 × 12 cm 2 , electrolytes are successfully fabricated by reactive sputtering on commercially obtained nickel oxide-yttria-stabilized zirconia (NiO-YSZ) anode without any pretreatment. Electrolytes of 6-μm-thick with gadolinium-doped ceria (GDC)|YSZ|GDC tri-layer configuration are fabricated with less than 2.5-h sputtering and followed by annealing at 1000 °C, much lower than that adopted in traditional wet process. In combination with traditional La 0.6 Sr 0.4 Co 0.2 Fe 0.8 O 3-δ (LSCF) cathodes, SOFCs with sputtered electrolytes show open circuit voltages close to the theoretical values, excellent electrochemical performances and long-term stability. The initial peak power densities of such cells reach 1.80, 1.24, 0.75 and 0.42 W cm −2 at 800, 750, 700 and 650 °C, respectively. The performance increases slightly in the initial stage and then stabilizes without degradation during the 300-h stability test under a constant voltage of 0.8 V at 650 °C. The scaled-up deposition area and the high deposition rate (∼2.5 μm h −1 ) show promising opportunities in the mass production of SOFCs using reactive sputtering.
engineering, chemical, environmental
-
Hierarchically oriented macroporous anode-supported solid oxide fuel cell with thin ceria electrolyte film.
Yu Chen,Yanxiang Zhang,Jeffrey Baker,Prasun Majumdar,Zhibin Yang,Minfang Han,Fanglin Chen
DOI: https://doi.org/10.1021/am5003662
IF: 9.5
2014-01-01
ACS Applied Materials & Interfaces
Abstract:Application of anode-supported solid oxide fuel cell (SOFC) with ceria based electrolyte has often been limited by high cost of electrolyte film fabrication and high electrode polarization. In this study, dense Gd0.1Ce0.9O2 (GDC) thin film electrolytes have been fabricated on hierarchically oriented macroporous NiO-GDC anodes by a combination of freeze-drying tape-casting of the NiO-GDC anode, drop-coating GDC slurry on NiO-GDC anode, and co-firing the electrolyte/anode bilayers. Using 3D X-ray microscopy and subsequent analysis, it has been determined that the NiO-GDC anode substrates have a porosity of around 42% and channel size from around 10 μm at the electrolyte side to around 20 μm at the other side of the NiO-GDC (away from the electrolyte), indicating a hierarchically oriented macroporous NiO-GDC microstructure. Such NiO-GDC microstructure shows a tortuosity factor of ∼1.3 along the thickness direction, expecting to facilitate gas diffusion in the anode during fuel cell operation. SOFCs with such Ni-GDC anode, GDC film (30 μm) electrolyte, and La0.6Sr0.4Co0.2Fe0.8O3-GDC (LSCF-GDC) cathode show significantly enhanced cell power output of 1.021 W cm(-2) at 600 °C using H2 as fuel and ambient air as oxidant. Electrochemical Impedance Spectroscopy (EIS) analysis indicates a decrease in both activation and concentration polarizations. This study has demonstrated that freeze-drying tape-casting is a very promising approach to fabricate hierarchically oriented porous substrate for SOFC and other applications.