Abstract:Mg–1Mn alloy, extruded at a low temperature in our published protocol, contributed to the intensified basal texture and extremely refined microstructure with spheroidal nanoscale precipitates dispersing throughout the matrix and along the grain boundaries, consequently resulting in the excellent mechanical properties where the alloy exhibited a tensile yield strength of 204.3 MPa and a ductility of 38.8% at room temperature. Therefore, Mg–1Mn alloy was recommended as one of the potential materials for structural applications. In the present investigation, hot deformation behavior through constitutive analysis and extrusion temperature-dependent microstructure, texture and mechanical properties of as-extruded Mg–1Mn alloy were investigated, aiming at revealing how extrusion temperature affected microstructure, texture, and mechanical properties of as-extruded Mg–1Mn alloy. X-ray diffraction patterns demonstrated that phase components of the experimental alloys consisted of the α-Mg matrix and Mn precipitates. Optical microscopy images indicated a significant increase in average grain size of the alloys as the extrusion temperature increasing from 250 °C to 400 °C. Scanning electron microscopy graphics revealed that coarsened particles identified as Mn precipitates by EDS were observed within the matrix when extrusion temperature reached 400 °C. Inverse pole figure maps of the experimental samples subjected to different extrusion temperatures in the present work exhibited the typical basal texture, suggesting that basal slip was activated hardly during the tensile stress applied along the extrusion direction. Consequently, extrusion temperature displayed the significant impact on microstructure, texture, and mechanical properties of as-extruded Mg–1Mn alloy. The alloy extruded at both 250 °C and 300 °C exhibited the strong basal texture and refined microstructure with spheroidal nanoscale precipitates dispersing within the matrix and along the grain boundaries, which contributed to their excellent comprehensive mechanical properties. The alloy extruded at 400 °C possessed the typical basal texture and coarsened microstructure, leading to the extremely poor mechanical properties. Simultaneously, the constitutive model of the Arrhenius equation based on Zener-Hollomon parameters was also established in the present investigation. Therefore, optimizing the extrusion temperature to regulate the microstructure, grain orientation distribution, and morphology of precipitates was considered as one of the effective approaches for achieving the excellent mechanical properties of Mg alloys.

Enhanced Mechanical Properties in Fine-Grained Mg–1.0Zn–0.5Ca Alloys Prepared by Extrusion at Different Temperatures

Microstructure Evolution and Properties of Mg-9Gd-0.8Al Alloy with Lamellar Phase During Extrusion at Different Temperatures

Microstructure and tensile properties of a low-alloyed magnesium alloy: effect of extrusion temperature

Effect of Hot Extrusion on Microstructure, Texture, and Mechanical Properties of Mg-Zn-Mn-0.5Ca Alloy

Achieving superior mechanical properties in a low-alloyed magnesium alloy via low-temperature extrusion

Microstructure, Tensile Properties and Work Hardening Behavior of an Extruded Mg–Zn–Ca–Mn Magnesium Alloy

Effect of extrusion parameters on microstructure and mechanical properties of Mg-0.12Ca-0.08Ba alloy

Effect of extrusion temperature on microstructure, mechanical properties, and deformation mechanism of Mg-2.5Er-0.6Zr alloy

Microstructure evolution, strengthening mechanisms and deformation behavior of high-ductility Mg−3Zn−1Y−1Mn alloy at different extrusion temperatures

Hot deformation behavior of novel high-strength Mg-0.6Mn-0.5Al-0.5Zn-0.4Ca alloy

Influence of Ca Content on Microstructure and Mechanical Properties of Extruded Mg–Al–Ca–Mn Alloys

Hot deformation behavior and extrusion temperature-dependent microstructure, texture and mechanical properties of Mg–1Mn alloy

Evolution of Microstructure, Mechanical Properties, and Corrosion Resistance of Mg–2.2Gd–2.2Zn–0.2Ca (wt%) Alloy by Extrusion at Various Temperatures

Microstructure and mechanical properties of a low-alloyed Mg-Zn-Al-Ca alloy: Effect of extrusion speed

Enhanced strength-ductility synergy and activation of non-basal slip in as-extruded Mg–Zn–Ca alloy via heterostructure

Fine-grained Mg–1Mn–0.5Al–0.5Ca–0.5Zn alloy with high strength and good ductility fabricated by conventional extrusion

Effects of extrusion process on microstructure, precipitates and mechanical properties of Mg-Gd-Y-Zr-Ag alloys

Investigation on corrosion behavior and mechanical properties of an extruded Mg-Zn-Al-Sn-Mn alloy

Effect of extrusion speed on microstructure and mechanical properties of the Mg-Ca binary alloy

Effects of extrusion on the microstructure and mechanical properties of Mg–Zn–Gd alloy reinforced with quasicrystalline particles

Lowering thermal expansion of Mg with the enhanced strength by Ca alloying