Abstract:The effect of the precipitation value (PV) of mixtures of strong and weak non-solvent additives (NSA) on the phase state and viscosity of polyethersulfone(PES)/dimethylacetamide(DMAc)/non-solvent solutions and on the structure and performance of PES membranes were studied. Polyethylene glycol 400 (PEG-400, PV > 1000), water (PV = 10.6), 85 % phosphoric acid (PV = 13.0), glycerol (Gly, PV = 27.8) and mixtures thereof were used as NSA for PES-DMAc solutions. Using Gly/PEG-400 mixtures it was established that the increase in PV of NSA leads to the increase of a miscibility gap on the phase diagram. At a constant concentration of Gly/PEG-400 mixture, the viscosity of the solutions decreases. For a constant ratio (0.94–0.95) of the NSA amount added to the polymer-solvent system to the NSA amount causes a phase separation of the casting solution (coagulation value) increase in PV of NSA Gly/PEG-400 leads to an increase of the membrane pure water flux (PWF) from 13 up to 150 l/m2 h at 1 bar. The most dramatic increase in PWF occurs in the range of PV 39.7–125 g/dL. The results of SEM study don’t show significant differences in the cross-section morphology of membranes for different PV of NSA. However, the thickness of the selective membrane layer increases from 1 up to 4.5 μm when PV increased from 39.7 up to 750 g/dL. Thus, these studies allow us to conclude that the structure and properties of ultrafiltration membranes depend not only on the coagulation value of the casting solution, but also on the precipitation value of NSA.

Effects of PVPK30 on Polyethersulfone with Cardo Ultrafiltration Membrane

Effect of Polyethlene Glycol on Membrane Forming Systems and Polyethersulfone with Cardo Performance and Structure

Study on the Gelation Kinetics in Polyethersulfone with Cardo Asymmetric Ultrafiltration Membrane

Effect of Coagulation Bath Temperature on the Structure and Performance of Polyethersulfone Hollow Fiber Membranes by Dry/wet Process

Effect Of Polyethersulfone On The Mechanical And Rheological Properties Of Polyetherimide-Modified Epoxy Systems

Engineering of hemocompatible and antifouling polyethersulfone membranes by blending with heparin-mimicking microgels

Effect of Formamide on Structure and Performance of PES, PPESK Ultrafiltration Membrane

Preparation and Performance of Polyethersulfone Hollow-Fiber Membrane

Ultrafiltration Membrane Formation of Pes-C, Pes and Ppesk Polymers with Different Solvents

Preparation of Casting Solutions for Poly (phthalazinone Ether Ketone) Ultrafiltration Membrane

EFFECT OF PVPK30 AND TWEEN80 ON PERFORMANCE OF HOLLOW UF MEMBRANE AND STRUCTURE

Ultrafiltration membranes prepared from polyethersulfone-grafted-poly (N-vinyl-pyrrolidone) synthesized via simultaneous irradiation in homogenous phase and their anti-fouling performance

Effect of Additives on the Morphology and Performance of Symmetric Network PVDF Membranes

Effect of PEG Additive on Formation of PEK-C Microporous Membrane

Effects of Operation Conditions, Solvent and Gelation Bath on Morphology and Performance of Ppesk Asymmetric Ultrafiltration Membrane

Preparation, characterization and performance of polyethersulfone ultrafiltration membranes

Preparation of PES ultrafiltration membrane for treatment of emulsified oily wastewater: Effect of solvent and non-solvent on morphology and performance

Influence of different non-solvent additives to the casting solution on the structure and properties of PES membranes

Effects of a dual functional filler, polyethersulfone-g-carboxymethyl chitosan@MWCNT, for enhanced antifouling and penetration performance of PES composite membranes

Analysis of Additives on Hydrophilic Properties and Filtration Properties of Polysulfone Ultrafiltration Membrane

Poly (phthalazinone Ether Sulfone Ketone) Properties and Their Effect on the Membrane Morphology and Performance