Abstract:Ultrafiltration hollow-fiber membranes were prepared from polyetherimide (PEI) with a wet spinning method. The effects of N,N-dimethylacetantide (DMAc) as a solvent additive in the internal coagulant and acetic acid as a non-solvent additive in the dope solution on the morphologies and performances of the membranes were investigated. The influences of PEI dope concentration on membrane morphologies and properties were also studied. Scanning electron microscopy (SEM) indicates that the addition of DMAc into the internal coagulant changes the inner fiber surface from a dense skin layer to a porous structure. However, the pure water flux of the membrane decreases with the increase of DMAc content. On the other hand, the addition of acetic acid into the casting solution promotes the spinodal demixing of the membratte-forming system and suppresses the macrovoid formation in the membrane. A nodular structure forms in the fiber skin layer. With increasing acetic acid content, the pure water flux of the membrane increases about 4-fold and the solute retention shows a slight decrease. The mechanical properties can also be improved slightly by this additive. The thermal resistance of the PEI ultrafiltration membranes prepared in this work was examined by hot water treatment at 80 degrees C. No change was observed in the permeation performance of the membranes, while the study of mechanical properties shows that the elongation-at-break of the membrane decreases slightly. PEI was sulfonated by chlorosulfonic acid (CSA) in 1,2-dichloroethane. With the increase of the molar ratio of CSA to PEI repeat unit and/or reaction time, the ion-exchange capacity (IEC) of the sulfonated polyetherimide (SPEI) increases accordingly. Water uptake test and contact angle measurements show that the hydrophillicity of the SPEI increases with the increase of the IEC. Polyetherimide/sulfonated polyetherintide (PEI/SPET) ultrafiltration hollow-fiber membranes were also prepared with a dry-wet phase inversion method and SPEI was used as a polymer additive. SEM study reveals that the addition of SPEI induces the formation of nodular structure and suppresses the formation of finger-like macrovoids. With the increase of air-gap distance, it was found that the number of micropores formed in the outer fiber surface and the pore size increased. On the other hand, the pure water flux of the membrane reaches a maximum and then decreases, while the solute retention decreases at first and then levels off at longer air-gap. Based on the filtration of bovine serum albuntin (BSA) solution, it was found that the use of SPEI in the blend membranes increased their hydrophilicity.

Analysis of Additives on Hydrophilic Properties and Filtration Properties of Polysulfone Ultrafiltration Membrane

Influence of additives on phase separation process of PVDF solution and membrane morphology

Improving Hydrophilicity And Protein Resistance Of Poly(Vinylidene Fluoride) Membranes By Blending With Amphiphilic Hyperbranched-Star Polymer

Development of High-Antifouling PPSU Ultrafiltration Membrane by Using Compound Additives: Preparation, Morphologies, and Filtration Resistant Properties.

Effect of Additives on the Morphology and Performance of Symmetric Network PVDF Membranes

The Filtration Properties for PEG Solutions of Different Structures Polysulfone Ultrafiltration Membranes

Enhanced Permeability and Fouling-Resistant Capacity of Poly(vinylidene Fluoride) Ultrafiltration Membrane Based on the PPG-co-PEG-co-PPG Copolymer with Two Hydrophobic Terminals and One Hydrophilic Intermediate.

Membranes of poly (vinyl butyral) (PVB) or cationic PVB (CPVB) blended with poly (vinylidene fluoride) (PVDF) prepared by a nonsolvent induced phase separation method: Miscibility and hydrophilicity

Fabrication of Polysulfone-Based Microfiltration Membranes and Their Performance Analysis

Preparation And Performance Of Ultrafiltration Membranes From Polyetherimide And Its Sulfonated Derivatives

Effect of the Addition of Polyacrylic Acid of Different Molecular Weights to Coagulation Bath on the Structure and Performance of Polysulfone Ultrafiltration Membranes

Effect of pore-forming/hydrophilic additive anchorage on the mesoporous structure and sieving performance of a blended ultrafiltration (UF) membrane

Enhanced permeability and antifouling properties of carboxylated polysulfone/quaternized polyimide blend ultrafiltration membrane

A Facile Approach to Fabrication of Superhydrophilic Ultrafiltration Membranes with Surface-Tailored Nanoparticles

Sulfonated Poly(?,?,?-Trifluorostyrene)-Doped Pvdf Ultrafiltration Membrane With Enhanced Hydrophilicity And Antifouling Property

Improving the hydrophilicity and fouling-resistance of polysulfone ultrafiltration membranes via surface zwitterionicalization mediated by polysulfone-based triblock copolymer additive

On the surface hydrophilization of a blended polysulfone membrane: atomic force microscopy measurement and molecular dynamics simulation

One-Step Water-Induced Phase Separation Simultaneously Triggering Polymer Solidification and Polyelectrolyte Complexation for Porous Ultrafiltration Membranes

Preparation of Polysulfone Composite Membrance and Study on Its Air Filtration Performance

Formation kinetics and characterization of polyphthalazinone ether ketone hollow fiber ultrafiltration membranes

Elaboration, characterization and application of polysulfone and polyacrylic acid blends as ultrafiltration membranes for removal of some heavy metals from water