Abstract:The main requirements of cemented carbides as cutting, machining, and drilling tools are wear resistance, chemical stability at high temperatures, and proper mechanical properties. However, some studies have indicated that the surface temperature of these tools increases locally during the cutting or machining process, which leads to oxidation, compositional change, and tool degradation over time. In addition, these tools are sometimes used in corrosive media such as saline water, etc. Cemented carbides contain carbide and metallic phases; therefore, there is a possibility of severe galvanic corrosion in these composites, which leads to the preferential dissolution of the metallic phase and the remaining carbide skeleton. On the other hand, the corrosion rate of hardmetals depends on the pH of the electrolyte. In alkaline electrolytes, Co passivation occurs; in contrast, WC actively dissolves. This behavior is vice versa in acidic electrolytes. Deposition of hard protective CVD coatings is an appropriate way to protect cemented carbides from environmental damage and oxidative wear. In past studies, it has been mentioned that using single-component coatings such as TiN is unsuitable for improving the cutting performance of such tools due to oxidative degradation of the coating. But the use of modified multilayer coatings has shown a significant improvement in the proficiency and lifespan of these cutting tools. In recent years, CVD TiAlN coatings have replaced the previous generation of hard coatings due to their unique properties. Much research has been carried out on the properties of these coatings, and the effect of different contents of Al and dopants have been reported. Recently, CVD TiSiCN coatings have been introduced as a new generation of hard coating that has attracted the attention of researchers. These composite coatings are one of the promising options for the next generation of wear-resistant coatings due to their ultra-high hardness, wear and oxidation resistance, and excellent performance in the cutting/machining process.

Research on Mechanics and Cutting Performance of Hard Carbide Cutting Tools of TiN-based Composite Coatings

Application of Magnetron Sputter Ion Plated CrAlTiN Composite Coating in Improving Wear Resistance of Milling Cutter

Comparative analysis over microstructural, mechanical properties and cutting performance of TiN, TiVN coatings deposited by magnetron sputtering on SiAlON ceramic tool insert

Structural characterization and adhesion appraisal of TiN and TiCN coatings deposited by CAE-PVD technique on a new carbide composite cutting tool

Investigations on microstructure, mechanical and tribological properties of TiN coatings deposited on three different tool materials

Study on the Orthogonal Cutting Process of Al7050T7451 with Uncoated and Coated Tools

Study on the effect of texture on cutting performance of the coated tool with finite element analysis and experimental method

Study on the preparation of hard and wear-resistant titanium nitride films on silicon nitride ceramic cutting tools

Mechanics and Cutting Performance of Multilayer Nanostructured TiAlN/TiSiN/ZrN Coatings

Durability of cutting tools with deposited ceramic–metallic coatings (Ti,Al)N – Cu and (Ti,Al)N – Ni when turning and milling steels

Study on tribology and cutting performance of boron doped diamond composite coated tool

A study on the mechanical performance and medium temperature tribological behavior of plasma nitrocarburizing/TiAlSiN/DLC composite coating

Properties and Performance of TiAlSiN and AlCrN Monolayer and Multilayer Coatings for Turning Ti-6Al-4V

Microstructure and Properties of the AlCrSi(O)N Tool Coatings by Arc Ion Plating

Recent developments in the new generation of hard coatings applied on cemented carbide cutting tools

Preparation and characterization of electrodeposited Ni–TiC, Ni–TiN, and Ni–TiC–TiN composite coatings on tungsten carbide cutting tool

Mechanical and cutting performance of cemented carbide tools with Cr/x/DLC composite coatings

Effect of Coating Thickness on the Characteristics and Dry Machining Performance of TiN Film Deposited on Cemented Carbide Inserts Using CFUBMS

Study on the growth and wear behavior of the TiAlN-based composite coating deposited on TiCN-based cermets with different binder phase

Comparative performance evaluation between ta-C and TiAlCrN coated tools during milling of additively manufactured CFRP composite

Analysis of tool wear and cutting characteristics in milling of powder metallurgy nickel-based superalloy by various coatings