Abstract:In this research, a linear low density polyethylene (LLDPE) was first melt blended with a series of high density polyethylenes (HDPE) with different molecular weights at a fixed ratio of LLDPE/HDPE=90/10 (w/w). The prepared HDPE/LLDPE blends were then injection-molded into specimen bars through a dynamic packing injection molding (DPIM) technique, in which an oscillating shear field was imposed on the melt by two pistons that move reversibly with the same frequency during the packing stage. The crystal morphology, orientation and tensile properties were characterized by scanning electron microscopy, two-dimensional wide-angle X-ray scattering and Instron, respectively. Compared with conventional injection molding, DPIM caused an obvious increase in tensile strength in the injection-molded bars. Interestingly, LLDPE blended with low molecular weight HDPE (LMW-PE) was found to possess much higher tensile strength than that blended with high molecular weight HDPE (HMW-PE). Shish–kebab morphology was observed for all blends obtained, regardless of the molecular weight of the HDPE. However, thicker but shorter lamellae were observed for the LLDPE/LMW-PE blend, corresponding to a higher melting temperature; while thinner but longer lamellae were seen for the LLDPE/HMW-PE blend, corresponding to a lower melting temperature. Furthermore, the phase miscibility between HDPE and LLDPE was found to increase with increasing HDPE molecular weight, which would affect the sensitivity of molecular chains for response to external shear. The changed miscibility, together with the changed entanglement density in different HDPE was responsible for the change in tensile strength and unique crystal morphology of LLDPE induced by adding HDPE.

Tensile Properties and Condensed Structure of Vibration Extruded HDPE Blends

The Microstructure-Tensile Property Relationship of Polyethylene Resin for Biaxially Stretched Film

Evolution of the cavity structure of HDPE/UHMWPE blends during cold stretching

Enhanced effect of thermal expansion process in rotational shear technology for high performance HDPE pipes

Deformation process and mechanism of HDPE/LDPE blends

Constructing highly oriented and condensed shish-kebab crystalline structure of HDPE/UHMWPE blends via intense stretching process:Achieving high mechanical properties and in-plane thermal conductivity

Unique crystal morphology and tensile properties of injection-molded bar of LLDPE by adding HDPE with different molecular weights

Exploring the Entangled State and Molecular Weight Ofuhmwpeon the Microstructure and Mechanical Properties Ofhdpe/uhmwpeblends

Study on Crystallization Kinetics of Partially Melting Polyethylene Aiming to Improve Mechanical Properties

Study on the fusion properties of extruded foaming rigid PVC

Simultaneously achieving self-toughening and self-reinforcing of polyethylene on an industrial scale using volume-pulsation injection molding

Study on fluidity and mechanics performance of UHMWPE/HDPE composite material

Tensile Behavior of High-Density Polyethylene Including the Effects of Processing Technique, Thickness, Temperature, and Strain Rate

Reversed thermal stability between stress-induced melting and recrystallized crystallites and original inclined ones in moderately stretched ultra high molecular weight polyethylene and high density polyethylene

Morphology evolution and mechanical property enhancement of linear low‐density polyethylene by adding disentangled ultrahigh molecular weight polyethylene

Dynamic Rheological Behavior of Hdpe/Uhmwpe Blends

Blending Recycled High-Density Polyethylene HDPE (rHDPE) with Virgin (vHDPE) as an Effective Approach to Improve the Mechanical Properties

Reinforcing High-Density Polyethylene by Polyacrylonitrile Fibers

THE EFFECT OF MECHANICAL VIBRATION ON CRYSTALLIZATION OF POLYPROPYLENE

The Chain Microstructure And Condensed Structure Of Polyethylene Resin Used For Biaxially Stretched Film

The influence of formation temperatures on the crystal structure and mechanical properties of ultrahigh-molecular-weight polyethylene/high-density polyethylene-blend fibers prepared by melt spinning