Abstract:The effects of temperature on the tribological and dynamic mechanical properties (DMP) of aromatic liquid-crystal poly(ester-co-amide) were investigated. Specimens for the DMA test and friction and wear test were prepared by compression molding at elevated temperature. The dynamic mechanical properties of the resulting compression-molded liquid crystal polymer (LCP) specimens were evaluated on a Perkin-Elmer DMA instrument, in a three-point bending mode, at a heating rate of 10°C/min and frequency of 1Hz from room temperature to 250°C. The friction and wear behavior of the compression-molded LCP specimens sliding against SA52100 steel in a ball-on-disk configuration was evaluated on a high-temperature friction and wear tester from 25 to 300°C. The worn surface morphologies of the compression-molded LCP specimens were observed on a scanning electron microscope. It was found that the tribological and dynamic mechanical properties of the LCP strongly depended on the test temperature. Namely, the friction coefficients decreased significantly and the wear rate increased considerably with increasing temperature. This was attributed to the enhanced softening and plastic deformation of the LCP at elevated temperature. The LCP experienced severe plastic deformation, flowing and local melting owing to the destruction of the stiff backbones of the polymeric molecules at excessively high temperature, thus the largest wear rate of the tested LCP was generated at 300°C. Such a trend in the friction and wear behavior of the compression-molded LCP with temperature conformed well to the corresponding worn surface morphologies. Namely, the LCP worn surface was characterized by mild plastic deformation and micro-cracking as the LCP disk slid against the steel ball at 50°C, whilst at 100°C, the plastic deformation and adhesion became severe and the micro-cracking disappeared owing to the plastic flow. The plastic deformation and adhesion became increasingly more severe with further increase of the test temperature up to 150, 200, and 250°C, owing to the increased plastic flow and local softening and melting of the LCP. Moreover, the storage modulus of the compression-molded LCP greatly decreased with increasing temperature, as did the loss modulus, while the complex modulus and tan δ increased with increasing temperature, which agreed well with the corresponding trend of the tribological behavior with temperature. It was confirmed that the dynamic mechanical properties of the polymer were an important factor of the high temperature tribological behavior.

THE EFFECT OF MECHANICAL VIBRATION ON CRYSTALLIZATION OF POLYPROPYLENE

Effects of Crystallization Temperature of Poly(vinylidene Fluoride) on Crystal Modification and Phase Transition of Poly(butylene Adipate) in Their Blends: a Novel Approach for Polymorphic Control.

Effect of Temperature on the Tribological and Dynamic Mechanical Properties of Liquid Crystalline Polymer

Vibration-Dependent Crystal Form of Isotactic Polypropylene under Nonisothermal Crystallization

Effect of Vibration on Crystal Morphology and Structure of Isotactic Polypropylene in Nonisothermal Crystallization

The Crystallinity of Pvc and Its Effect on Physical Properties

Effect of rapid heating cycle injection mold temperature on crystal structures, morphology of polypropylene and surface quality of plastic parts

INFLUENCE OF THERMAL TREATMENT ON CRYSTAL MELTING BEHAVIOR AND CRYSTAL STRUCTURE OF NYLON 6 AND POLYAMIDE BLOCK COPOLYMER/NYLON 6 BLENDS

Additive Effects of N,N,N′,N′ -Tetraalkyl Terephthalamide on Crystalline Morphology and Mechanical Properties of Polypropylene

INFLUENCE OF HEAT TREATMENT ON CRYSTALLIZATION BEHAVIOR OF POM

Influence of Syndiotacticity and Annealing Temperature on the Double Melting Peak Behaviour of Syndiotactic Polypropylene

The Effect of Thermal History on Crystalline Structure and Mechanical Properties of Β-Nucleated Isotactic Polypropylene

Effect of heat treatment on the mechanical properties of PBT/PET yarn

Simultaneously Improving The Toughness, Flexural Modulus And Thermal Performance Of Isotactic Polypropylene By Alpha-Beta Crystalline Transition And Inorganic Whisker Reinforcement

THE INFLUENCE OF THERMAL TREATMENT ON EPITAXIAL CRYSTALLIZATION IN HDPE/iPP BLENDS

The Effects Of Crystallization Condition On The Microstructure And Thermal Stability Of Istactic Polypropylene Nucleated By Beta-Form Nucleating Agent

Effect of poly(lactic acid) crystallization on its mechanical and heat resistance performances

Crystallinity and mechanical properties of polypropylene products foamed by microcellular injection molding process

EFFECT OF PREPARATION METHODS ON CRYSTALLINE STRUCTURE OF <I>i</I>PP/EPR BLENDS

Crystallization Behaviors and Mechanical Properties of Polypropylene Grafted by Vinyl Silane/Styrene

Investigation of tensile behavior and molecular structure of the thermoplastic polyurethane sheets injection molded at different mold temperatures