Abstract:(Pbx,Sr1−x )0.85Bi0.1TiO3 thin films with the perovskite phase structure were prepared on an ITO glass substrate by sol-gel method. X-ray diffraction (XRD), scanning electron microscopy (SEM) and an impedance analyzer were respectively used in order to characterize the phase status, morphology and dielectric properties of the thin films. The results show that during the formation process of (Pbx,Sr1−x )0.85Bi0.1TiO3 thin films, the nucleus of the perovskite phase are initially formed and then congregated. These aggregated nucleus are then transformed as the perovskite-phase crystalline in the thin film. Finally, the crystalline phase grows and separates gradually to form the perfect crystalline-phase structure. The content of the perovskite phase formed in the thin film under rapid thermal process (RTP) is more than that formed under traditional heat treatment with kinetic equilibrium. This is due to the high active decomposed ions that form the perovskite phase directly when heat-treated by RTP. The formation of the perovskite phase therefore overcomes a much lower barrier under RTP than that under traditional calcinations. The structure of the perovskite phase has a close relation to the ratio of Pb/Sr in the system because of the radius difference between Pb2+ and Sr2+. The transformation temperature between the cubic and the tetragonal structures of the perovskite phase increases with increasing Pb2+ content because the radius of Pb2+ is larger than that of Sr2+. It appears at room temperature when the content of Pb2+/Sr2+ is about 40/60 in the thin film. Meanwhile, the tetragonality of the perovskite phase is increased when Pb2+ ions increase due to its high polarization. The higher tunability of the (Pbx,Sr1−x )0.85Bi0.1TiO3 thin film is exhibited when the film composition is close to the transformation point between the paraelectric and ferroelectric phases. Pb2+ ions show a dominant factor to affect the Curie point of the system and then changing tunability.

Preparations and Dielectric Properties of Ba0.80Sr0.20TiO3/PbO–B2O3 Thick Films

The Structures and Dielectric Properties of Ba0.80Sr0.20TiO3/Pb0.82La0.18TiO3 Composite Thick Films with Addition of PbO–B2O3 Glass

The Effect of B2o3-Li2co3 Addition on Sintering Behavior and Dielectric Properties of Ba0.6sr0.4tio3 Ceramics

Effect of PbO-B<sub>2</sub>O<sub>3</sub> Glass Additive on the Dielectric Properties of Ba<sub>0.80</sub>Sr<sub>0.20</sub>TiO<sub>3</sub> /Pb<sub>0.88</sub>La<sub>0.12</sub>Ti<sub>0.97</sub>O<sub>3</sub> Composite Thick Films

Enhanced Piezoresponse and Dielectric Properties for Ba1-XSrXTiO3 Composition Ultrathin Films by the High-Throughput Method

Fabrication Of Ba0.6sr0.4tio3 Ceramic Thick Film By Electrophoretic Deposition Process

Influence of Pb on the structure and dielectric properties of (Pb-x,Sr1-x)(0.85)Bi0.1TiO3 thin films

Sintering Behavior and Dielectric Property of BST-BSL Composite Ceramics

Improving Energy Storage Properties in (ba0.75sr0.1bi0.1)(ti0.9zr0.1)o3 Ceramic Thick Films by Adding (sb0.5li0.5)tio3, Domain Engineering and Defect Engineering

Effect of PbO-B<sub>2</sub>O<sub>3</sub> Glass Additive on the Dielectric Properties of Ba<sub>0.80</sub>Sr<sub>0.20</sub>TiO<sub>3</sub> /Pb<sub>0.88</sub>La<sub>0.12</sub>Ti<sub>0.97</sub>O<sub>3</sub> Composite Thick Films

Effect of lead on formation and dielectric tunability of (Pb<sub>x</sub>,Sr<sub>1− <i>x</i> </sub>)<sub>0.85</sub>Bi<sub>0.1</sub>TiO<sub>3</sub> thin films

Enhanced low electric-field energy-storage performance in Ba0.9Sr0.1TiO3-Bi(Mg1/2Ti1/2)O-3 ceramics

Effect of Lead on Formation and Dielectric Tunability of (pbx,sr1−x )0.85bi0.1tio3 Thin Films

Low-temperature Sintering and Electrical Properties of Ba0.68Sr0.32TiO3 Thick Films

Investigation of Thickness Dependence of Structure and Electric Properties of Sol-Gel-Derived BiScO3-PbTiO3 Thin Films: Investigation of Properties of BiScO3-PbTiO3 Thin Films

Preparation and Properties of (Ba-X,sr1-x)tio3 Thin Film for High Density Dram Application

In Situ Preparation Of High Dielectric Constant, Low-Loss Ferroelectric Batio3 Films On Si At 500 Degrees C

Preparation of (1− <i>x</i> %)(Na<sub>0.5</sub>Bi<sub>0.5</sub>)TiO<sub>3</sub>– <i>x</i> %SrTiO<sub>3</sub> thin films by a sol–gel method for dielectric tunable applications

PREPARATION OF CALCIUM DOPED STRONTIUM BISMUTH TITANATE FERROELECTRIC THIN FILMS BY SOL-GEL PROCESSING

Fabrication and Ferroelectric Properties of Ba-Doped Strontium Bismuth Titanate Ceramics

Fabrication and Properties of Sol–Gel‐Derived BiScO3–PbTiO3 Thin Films