Abstract:Blending type of ABS with different polybutadiene rubber (PB) and polyacrylonitrile (AN) contents in SAN phase is prepared at 240 degrees C to study the effects of PB and AN content on the structure and the properties of DB/ABS blends. Different kinds of productive ABS along with the blend-type ABS are used to compare the properties of PC/ABS and DB/ABS blends comprehensively. All blends are made by melt blending for 10 min with sheer rate of 30 r/min. The result shows that, in DB/Blend-type ABS (70/30) blends, PB content exhibits significant influence on the tensile properties. Samples with 6.3 wt% of PB always show the best performance both in yield strength and elongation at break when AN content is fixed at 18 wt%, 25 wt% and 30 wt%; while increasing AN content in the sample with the same PB content would result in better blends properties even not so obvious as PB content. Scanning electron microscopy gives exactly the same trend for phase morphology with PB and AN contents, revealing best uniform scale of dispersed phase (ABS) among 0.5 - 1.2 mu m at 6.3 wt% of PB. Thermal gravimetric analysis shows that all DB/ABS blends have good thermal stability, which is not obviously affected by PB content and AN content. Single peak of glass transition shows good compatibility in the DB/ABS blends. Excellent compatibility of DB with ABS in the sample is exhibited through dynamic mechanical analysis. The glasstransition temperature of DB/ABS blends are closed to that of DB, mildly affected by PB and AN content. Besides, both blending type ABS and different kinds of productive type ABS are used to compare the properties of DB/ABS blends and traditional bisphenol-A-type PC/ABS blends. Basic laws of tensile properties in DB/ABS remain the same as in PC/ABS blends using different types of ABS.

Phase Morphology Evolvement and Properties of High Flowability PC/ABS Alloy

Tensile and Fracture Behaviors of Pc/Abs Polymer Alloy

Blending ABS resin and its effect on structure and properties of PC/ABS BLEND alloy

Research on effect of ABS,MAH,DCP on property of PA6/ABS blend

Effect of Morphology on Crack Extension Property of PC/ABS Polymer Alloy.

Research on high quality PC/ABS alloy

The Effect of Blending Sequence on Phase Morphology of Nylon 6/abs/sma Blends

Rheological Properties and Morphology of PC/AES Blends

Preparation of PC MABS Alloys by Bulk and Their Properties

MORPHOLOGY AND MECHANICAL PROPERTIES OF NYLON-6/ABS POLYMER BLENDS COMPATIBILIZED BY STYRENE-MALEIC ANHYDIDE COPOLYMER

Morphology on ABS and PC/ABS Series of Polymer Alloy Influence on Mechanical Properties

Structure and Properties of Isosorbide type Polycarbonate/ABS Blend

Creating Super-Tough and Strong PA6/ABS Blends Using Multi-Phase Compatibilizers

Phase Modification of Acrylate Rubber/Chlorinated Polypropylene Blends by a Hindered Phenol Compound

Effect of Compatibilizer and Nucleation Agent on the Properties of Poly(lacticacid)/Polycarbonate (PLA/PC) Blends

Phase Separation of Impact‐modified PVC/PMMA Blends under Melt‐blending Conditions

The Effect of Phase Structure on the Tribological Properties of PA66/HDPE Blends

Effect of Phase Morphology on the Reactive Blending

Influences of component ratio of minor phases and charge sequence on the morphology and mechanical properties of PP/PS/PA6 ternary blends

Study on Properties of PC/PA1010 Solvent Resistance Alloy Systems

Effect of Compatibility on the Foaming Behavior of Injection Molded Polypropylene and Polycarbonate Blend Parts