Abstract:TiF3-doped NaH/Al mixture was hydrogenated into Na3AlH6 and NaAlH4 complex hydrides by reactive ball-milling at room temperature through the optimization of milling duration and hydrogen pressure. The analysis of the preparation of NaAlH4 samples during reactive ball-milling process has been performed by XRD and TG/DSC. It has been found that Na3AlH6 was formed under 0.5 MPa hydrogen pressure and 30 h milling duration, while NaAlH4 was formed under 0.8 MPa hydrogen pressure and 45 h milling duration. The process of preparing NaAlH4 by ball-milling was found accomplished via two reaction steps, namely: (1) NaH + Al + H-2 Na3AlH6 and (2) Na3AlH6 + Al + H-2 -> NaAlH4. As the hydrogen pressure and milling duration increase, the synthetic yield of NaAlH4 and its corresponding dehydriding capacity are both increased. With increased hydrogen pressure (0.8-3 MPa) and milling duration (45-60 h), the cell volume of Na3AlH6 decreases while that of NaAlH4 increases gradually. The abundance of Na3AlH6 phase decreases from 57.76 (x = 0.8, y = 45) to 8.69 wt.% (x = 3, y = 60), and the abundance of NaAlH4 phase increases from 20.63 (x = 0.8, y = 45) to 86.50 wt.% (x = 3, y = 60). All the samples prepared in this way have fairly good activation behavior and fast hydriding/dehydriding reaction kinetics, which are capable of absorbing 4.26 wt.% hydrogen at 120 degrees C and desorbing 4.12 wt.% hydrogen at 150 degrees C, respectively. The improvement of hydriding/dehydriding properties is ascribed to the favorable microstructure and ultrafine particle features of nanosized NaAlH4 formed during ball-milling at the optimum synthetic condition. (C) 2010 Professor T. Nejat Veziroglu. Published by Elsevier Ltd. All rights reserved.

The Study of the Synthetic of Sodium Aluminum Hydride under Low Pressure

Study on Hydrogen Generation from the Hydrolysis of a Ball Milled Aluminum/calcium Hydride Composite

Investigation on the Improved Hydrolysis of Aluminum–calcium Hydride-Salt Mixture Elaborated by Ball Milling

The Hydrogen Storage Properties and Microstructure of Ti-Doped Sodium Aluminum Hydride Prepared by Ball-Milling

Improved Hydrogen Generation from the Hydrolysis of Aluminum Ball Milled with Hydride

Synthesis and Hydriding/dehydriding Properties of Nanosized Sodium Alanates Prepared by Reactive Ball-Milling

Influence of Temperature and Hydrogen Pressure on the Hydriding/dehydriding Behavior of Ti-doped Sodium Aluminum Hydride

The Research of Liquid Phase Synthesis of Sodium Aluminum Hydride

Improving MgH2 formation kinetics and its effect on NaBH4 synthesis

Dehydriding Properties of Ti Or/and Zr-doped Sodium Aluminum Hydride Prepared by Ball-Milling

Catalytical Synthesis and In Situ Doping of Sodium Aluminum Hydride from Elements

Directed Stabilization by Air-Milling and Catalyzed Decomposition by Layered Titanium Carbide Toward Low-Temperature and High-Capacity Hydrogen Storage of Aluminum Hydride

Preparation of Ti-Doped Sodium Aluminum Hydride from Mechanical Milling of NaH/Al with Off-the-Shelf Ti Powder

Preparation and hydrogen storage characteristics of Ti-NaAlH4 complex hydride

Electron Microscopy Study of Ti-Doped Sodium Aluminum Hydride Prepared by Mechanical Milling Nah/Al with Ti Powder

Ball Mill Effect on the Dehydrogenation Kinetics of LiAlH4

Hydrogen Storage Properties of La1.8Ca0.2Mg14Ni3 Alloy Prepared by Ball Milling in Different Milling Environments

Dehydriding properties of γ-AlH3

Effect of Salts Addition on the Hydrogen Generation of Al–LiH Composite Elaborated by Ball Milling

Aluminum nanoparticles manufactured using a ball-milling method with ammonium chloride as a grinding aid: achieving energy release at low temperature

Microstructures and hydrogen storage characteristics of nanocrystal/amorphous Mg17Al12 alloy prepared by ball-milling