Abstract:Schematic of sequential melting and sintering process on morphology development of UHMWPE/LDPE blends. Blending ultra‐high molecular weight polyethylene (UHMWPE) with a low molecular weight polyolefin is a well‐established technique to improve its processability. The binary blends of UHMWPE and low‐density polyethylene (LDPE) were prepared with varying LDPE content (10%, 20%, 30%, 40%, and 50% by wt.) leading to the formation of a single polymer composite system (SPCS) as melting and sintering followed preferential stages during mixing. Interestingly, the sequence of either "melting followed by sintering" or "simultaneous sintering and melting" depends on the LDPE content in the blend, resulting in unique blend morphology. Separate melting peaks for the blend's constituents were observed in thermal characterization, showing the blend's immiscibility, while intermediate peaks showed moderate miscibility in the melt state. Due to the high entanglement density, UHMWPE retained a solid‐like structure and showed an intense viscous nature even above the melting point in rheological characterization. Typically, the UHMWPE samples are fabricated by boundary fusion between particles called sintering. At LDPE content higher than 30 wt.%, the sea island structure was visible in morphological analysis, and the preexisting cavities reduced the tensile modulus by 54% in the blend, along with decreased elongation at failure (250%–100%). Similarly, the flexural modulus was reduced by 34.7% in the blends, along with the decreased flexural strength. Interestingly, the decrease in performance properties occurred in two steps over the range of LDPE content. Thus, it was clear that 30 wt.% of LDPE in the UHMWPE/LDPE blend represented the critical concentration for controlling melting and sintering sequence to develop specified morphology and performance properties. These blends have the potential for biomedical application as well as for the development of foam products, which is the further scope of the present study.

Molecular Weight Distribution and Properties of Bimodal Polyethylene Blends Prepared by Controlling Molecular Chain

Poly(L-Lactide) Materials with Balanced Mechanical Properties Prepared by Blending with Peg-Mb-Ppa Multiblock Copolymers

Well-Defined Pe-B-Pdms Diblock Copolymers Via The Combination Of Thiol-Ene Click And Esterification Reactions: Facile Synthesis And Compatibilization For Hdpe/Silicone Oil Blends

Rheological Behavior and Mechanical Properties of High‐density Polyethylene Blends with Different Molecular Weights

Facile Preparation of Bimodal Polyethylene with Tunable Molecular Weight Distribution from Ethylene Polymerization Catalyzed by Binary Catalytic System in the Presence of Diethyl Zinc

Morphology evolution and mechanical property enhancement of linear low‐density polyethylene by adding disentangled ultrahigh molecular weight polyethylene

Exploring the Entangled State and Molecular Weight Ofuhmwpeon the Microstructure and Mechanical Properties Ofhdpe/uhmwpeblends

Dynamic Rheological Behavior of Hdpe/Uhmwpe Blends

Molecular weight distribution shape approach for simultaneously enhancing the stiffness, ductility and strength of isotropic semicrystalline polymers based on linear unimodal and bimodal polyethylenes

Preparation of PBT/POE‐g‐GMA/PP Ternary Blends with Good Rigidity–toughness Balance by Core–shell Particles

Ultra-high molecular weight polyethylene (UHMWPE)/high-density polyethylene (HDPE) blends with outstanding mechanical properties, wear resistance, and processability

Rheological Properties and Morphological Evolutions of Polypropylene/Ethylene-Butene Copolymer Blends

Revealing the Effect of the Molecular Weight Distribution on the Chain Diffusion and Crystallization Process under a Branched Trimodal Polyethylene System

PROGRESS IN ULTRA HIGH MOLECULAR WEIGHT POLYETHYLENE/POLYPYLENE BLENDS

Influence of sequential melting and sintering process on morphology development and performance properties of ultra‐high molecular weight polyethylene/low‐density polyethylene blends

Polyethylene with bimodal molecular weight distribution synthesized by 2,6-bis(imino)pyridyl complexes of Fe(II) activated with various activators

Effect of polypropylene molecular weight distribution on the balance between the toughness and rigidity of the impact polypropylene composites

Deformation and Molecular Orientation in Films of Metallocene Polypropylene, Ethylene-Butylene Rubber, and Their 80/20 (W/W) Blend Revealed by the Simultaneous Kinetic Measurement of Microscopic Infrared Dichroism, Macroscopic Stress, and Mesoscale Strain

Effect of composition distribution on miscibility and co-crystallization phenomena in the blends of low density polyethylene with conventional and metallocene-based ethylene–butene copolymers

Synthesis of Polyethylene with Bimodal Molecular Weight Distribution by Supported Iron‐based Catalyst

Synthesis and Characterization of High‐density Polypropylene‐grafted Polyethylene Via a Macromolecular Reaction and Its Rheological Behavior