Abstract:Polylactide (PLA), a promising biodegradable and renewable polymer, finds many applications, particularly, used as biodegradable fiber in textile industry. The key is to improve its heat resistance. In this work, small amount of poly (D-lactide) (PDLA) was added firstly into poly (L-lactide) (PLLA) matrix to form stereocomplex polylactide (SC-PLA), which has much better heat resistance than that of PLLA matrix. Then two melting temperatures were adopted for fiber spinning, the one (210 degrees C) is far below the melting temperature of SC-PLA (i.e., 220-230 degrees C), and the other (225 degrees C) is close to the melting temperature of SC-PLA. The boiling water shrinkage and tensile strength of PLLA/PDLA fibers were investigated as function of PDLA content. It was found, the boiling water shrinkage could be largely reduced to as low as 5.6% and a satisfactory tensile strength (628 MPa) is achieved for fibers spun at 225 degrees C, compared with fibers spun at 210 degrees C (7.5% and 500 MPa, respectively), as the PDLA content is 3 wt%. SEM observation suggests a formation of nanofibrillar like SC-PLA structure as spun at 225 degrees C, while only spherical SC-PLA particles as spun at 210 degrees C. DSC result indicates that adding PDLA could largely enhance the crystallization rate of PLLA, but almost a constant crystallinity and SC-PLA content were observed for both spun fibers, disregarding the spinning temperatures. Herman's orientation parameters of spun fiber were obtained from 2D-WAXD, which suggests that fiber spun at 225 degrees C has higher orientation than that of fiber spun at 210 degrees C. Thus it can be concluded that the formation of nanofibrillar like SC-PLA and enhanced orientation degree contribute mainly to the improved heat resistance and tensile strength. This work presents a feasible and effective way to fabricate all-PLA-based fibers with the outstanding heat resistance by adding a small amount of PDLA and using a suitable spinning temperature.

Study on melt spinning process and properties of trilobal profiled polylactic acid fiber

Characterization of Poly(l‐lactic Acid) Fibers Produced by Melt Spinning

The Study of Correlations among the Process Condition, Structure and Property for Poly(l-Lactide) Fibers

An insight on the process–property relationships of melt spun polylactic acid fibers

Preparation and Characterization of Poly(lactic acid) Micro- and Nanofibers Fabricated by Centrifugal Spinning

DSC Studies on the Dyeing Properties of PLA Fiber

Simultaneous Enhancement of Strength and Toughness of PLA Induced by Miscibility Variation with PVA.

An insight into enhancing the physical properties of poly(lactic acid) (D600) fibers

Properties and structure of polylactide/poly (3-hydroxybutyrate- co -3-hydroxyvalerate) (PLA/PHBV) blend fibers

Achieving All-Polylactide Fibers with Significantly Enhanced Heat Resistance and Tensile Strength Via in Situ Formation of Nanofibrilized Stereocomplex Polylactide

Melt spinning process of biodegradable PLA filaments

Robust Interfacial Cylindrites of Polylactic Acid Modulated by an Intense Shear Flow Field

Morphology control of PLA microfibers and spheres via melt electrospinning

Effect of Molecular Weight on the Properties and Structure of Biodegradable Poly-lactic Acid Melt-Blown Nonwovens

Toward durable polylactic acid/poly(methyl methacrylate) polyblend fibers with high performance

Study on the preparation and properties of aligned carbon nanotubes/polylactide composite fibers

Composite fiber of PDLLA / HA produced by melt spinning technology

Tailoring Structure-Dominated Mechanical Properties of Poly(L-Lactide Acid) Monofilaments Via Controllable Molecular Relaxation

Morphology and Mechanical Properties of Electrospun Spidroin/PLLA Fiber Bundles

[A Study on the Mechanical Properties of Poly-D,l-lactic Acid/hydroxyapatite Compound Fibers].

Preparation and Characterization for the Thermal Stability and Mechanical Property of PLA and PLA/CF Samples Built by FFF Approach