Abstract:Micro-EDM is an unconventional technology used to machine every type of electrically conductive material regardless of its mechanical properties. Material removal occurs through electrical discharges between the workpiece and the electrode immersed in a dielectric fluid. In drilling operations, the technology is able to realise microholes with excellent quality in terms of precision, quality surface, roundness, and taper to the detriment of the machining time, which is less than other technologies. Several efforts are being made to improve different features related to the process performance that are severely affected by both the operative conditions, such as the electrode material or the type of dielectric, and process parameters. The typical indexes used to characterise the performance are the machining time, the material removal rate, and the geometric indexes. These indexes are very effective and are easily measurable, but they do not give information about the evolution of the drilling process, which could be irregular due to the different phenomena occurring during machining. The aim of this paper is the development of a method able to elaborate the motion law of the electrode during the micro-EDM drilling operation. In order to do this, a single hole was manufactured in several steps, recording both the machining time and electrode wear for each step. In this way, the actual position of the electrode during the drilling can be measured without the use of a predictive model for electrode wear. It was tested to confirm that the multistep procedure did not introduce new phenomena, in contrast to the traditional drilling operation. This method was used to study the effects of the electrode diameter, the type of electrode, the length of the electrode out of the spindle, and the entity of the run-out on the process performance. The tests were executed on titanium alloy sheets using a tungsten carbide electrode and hydrocarbon oil as the dielectric. It was found that the descent of the electrode into the workpiece was not regular, but it depended on the level of debris concentration in the machining zone. The debris concentration was influenced by the type and diameter of the electrode, its length out of the spindle, and, to a lesser extent, the run-out. This method was found to be a useful method for an in-depth analysis of the micro-EDM drilling process, contributing to a better understanding of the physical aspects of the process.

A Study on Micro-Hole Machining of Polycrystalline Diamond by Micro-Electrical Discharge Machining

Comparative Study of Ultrasonic Vibration-Assisted Die-Sinking Micro-Electrical Discharge Machining on Polycrystalline Diamond and Titanium

Edge fabrication and process optimization of precision woodworking PCD millers with disk electrical discharge machining

Study of Alternating Current Flow in Micro-Edm Through Real-Time Pulse Counting

An Analysis of the Uneven Tool Electrode Wear Mechanism in the Micro-electrical Discharge Machining Process

Advances in polycrystalline diamond (PCD) micro drills for efficient micro-hole machining in hard-brittle materials: a review of design, fabrication, and performance

A High Energy Density Pulsed Power Supply for Micro EDM of High Aspect Ratio Holes

Study on the Electrical and Geometrical Parameters of Micro Electrical Discharge Machining

Study on Electrical Discharge and Ultrasonic-Assisted Mechanical Combined Machining of Polycrystalline Diamond

Study on Micro-hole Electrochemical Machining Process with Sidewall-insulated Tool Electrode

Experimental study on surface physical behaviour and integrity of polycrystalline diamond (PCD) in micron-scale abrasive flow assisted impulse-discharge machining

Multiphysics Research on Electrochemical Machining of Micro Holes with Internal Features

Micro-EDM of micro-stepped hole based on the wear of micro-bit

Micro-EDM of micro-stepped hole in YG8 cemented carbide by using micro milling cutter

Machining efficiency and geometrical accuracy on micro-EDM drilling of titanium alloy

Study of the Law Motion of the Micro-EDM Drilling Process

Research on Electronic Discharge Grinding of Polycrystalline Diamond Based on Response Surface Method

Micro Electrical Discharge Machining of Ultrafine Particle Type Tungsten Carbide Using Dielectrics Mixed with Various Powders

Evaluation of milling performance of 50-μm D-shaped carbide tool, polycrystalline diamond-coated carbide tool, and polycrystalline diamond tool

A study on ultrasonic-assisted micro-EDM of titanium alloy

Investigation of micro-electro-discharge machining process parameters during machining of M2 hardened die-steel