Abstract:A quantitative evaluation method is used to monitor the extraction effect of four test holes in a field test conducted at Ping Coal Mine 10. The results indicate that, after adopting in situ downhole repair technology in the early stage of extraction, the average air leakage of Borehole No. 4, which failed due to air leakage in the borehole, decreased from 9.33 to 1.26 L/min (a reduction of 86.5%). Similarly, that of Borehole No. 3, which failed due to penetration of fissures in the surrounding rock, had an air leakage drop from 8.35 to 1.34 L/min (a reduction of 84.0%). These improvements demonstrate the remarkable effectiveness of the method. The quantitative evaluation method established in this study is not only simple to operate but also stable and reliable. In this study, a new method is proposed to quantitatively determine the extraction of boreholes under the effect of time. The main purpose of this method is to divide the gas drilling holes in the monitoring time into two stages: the early stage of extraction and the middle stage of extraction. The early stage of extraction uses the gas pressure difference to detect the gas tightness of the drilling holes and determine the type of gas leakage of the drilling holes. Moreover, the unqualified drilling holes are repaired immediately to ensure that all the drilling holes in the middle stage of the monitoring are the qualified holes at the early stage of the inspection. In the middle of extraction, the average attenuation rate of the fitting attenuation curve of pure gas extraction in the extraction borehole is calculated by monitoring, the growth rate of the linear fitting of the pure air leakage is calculated, and their ratios are used as the basis for judging the repair value of the gas leak borehole and the gas leak borehole. This quantitative evaluation method is used to monitor the extraction effect of four test holes in a field test conducted at Ping Coal Mine 10. The results indicate that, after adopting in situ downhole repair technology in the early stage of extraction, the average air leakage of Borehole No. 4, which failed due to air leakage in the borehole, decreased from 9.33 to 1.26 L/min (a reduction of 86.5%). Similarly, that of Borehole No. 3, which failed due to penetration of fissures in the surrounding rock, had an air leakage drop from 8.35 to 1.34 L/min (a reduction of 84.0%). These improvements demonstrate the remarkable effectiveness of the method. The quantitative evaluation method established in this study is not only simple to operate but also stable and reliable. Thus, it is feasible to be applied in the field, which provides important technical support for the improvement in gas extraction effect during coal mine safety production.

Improvement of Fixed Hole Craft in Construction Technology of Kilometer Rig

Study on construction technology of percussive reverse circulation drilling hole forming squeezed branch pile

Study on the mechanical properties and microstructure of a rich-watered grouting material

Research on an evaluation method for the strength of broken coal mass reinforced by cement slurry based on digital drilling test technology

Industrial test of new sealing method with fixed site and length

Development and Application of Water Sealing Technology for Gas Drainage Boreholes

Research and application of hydraulic fracturing borehole bag sealing technology

Improvement of drilling quality using precision directional drilling technology

Experimental Research on Performance of New Gas Drainage Borehole Sealing Material with High Fluidity

Development and performance optimization of a new composite sealing material prepared by drilling cuttings

CONSTRUCTION TECHNOLOGY AND PILE QUALITY ANALYSIS OF SUPER-LONG ROCK-SOCKETED PILE CROSSING A HUGE-THICK GRAVEL LAYER

Development of Cement-Based Grouting Material for Reinforcing Narrow Coal Pillars and Engineering Applications

Quality Control for Fabricating Large Diameter Bored Piles in Collapsible Sand Layer Areas

Preparation of a New Borehole Sealing Material of Coal Seam Water Infusion

Parameter Optimization of Constant Pressure Grouting Technology for Borehole Sealing with Inorganic Noncondensable Material in Tectonic Coalbed of South China

Structure Restrengthening Process and Mechanical Properties of Damaged Weakly Cemented Mudstone

Quantitative evaluation of the sealing effect of penetrating gas drilling and in situ repairing technology for smooth holes

Study on Performance Optimization of Water-Rich Grouting Materials Based on Response Surface Methodology

Numerical Simulation and Optimization of Hole Spacing for Cement Grouting in Rocks

Development of high-performance fiber-reinforced concrete for drilling wellbore walls in highly mineralized strata and its sulfate attack resistanceattack resistance

Experimental research on mechanical performance of grouting plugging material with large amount of fly ash