Abstract:In the presence of styrene (St), the melting-grafting of maleic anhydride (MAH) onto polypropylene was conducted in Haake torque rheometer and twins screw extruder (TSE) respectively. In experiments the dicumyl peroxide (DCP) concentration, St concentration, MAH concentration, reaction time, reaction temperature and screw speed were varied respectively. Results show that with the DCP concentration increasing, both the grating degree of MAH and melt flow index (MFR) of the grafted product increase at first and then deerease. When maintaining MAH concentration and increasing St concentration, the grafting degree of MAH reaches maximum at St:MAH=1mol?mol?1 and MFR always keeps decreasing. When maintaining St concentration and increasing MAH concentration, the grafting degree of MAH increases at first and then slightly decreases, and during which the MFR has a maximum point. With the reactive time increasing, both the grating degree of MAH and MFR of the grafted product increase at first and then decrease. When temperature is too high, the grafting degree of MAH decreases and the scission of the grafted product increases. When screw speed is low, the grating degree of MAH is low too, and when screw speed is high, the scission of the grafted product increases. The grafting of MAH in TSE is lower than that in Haake torque rheometer, while MFR of the grafted product in TSE is much lower than that in Haake torque rheometer. Based on the mechanism of melt-grafting, the above experimental results were discussed and explained.

Solvothermal preparation of maleic anhydride grafted onto acrylonitrile–butadiene–styrene terpolymer (ABS)

Study on Melt-Grafting of Maleic Anhydride Onto Polypropylene in the Presence of Styrene

Simultaneous Graft Polymerization of Polypropylene with Maleic Anhydride and Butyl Acrylate

Modification of Acrylonitrile–butadiene–styrene Terpolymer by Grafting with Maleic Anhydride in the Melt. I. Preparation and Characterization

Grafting copolymerization of maleic anhydride onto styrene-butadiene-styrene block copolymer through solvothermal process

Solvothermal Preparation and Characterization of Maleic Anhydride Grafting High Density Polyethylene Copolymer

Modification of acrylonitrile-butadiene-styrene terpolymer by graft copolymerization with maleic anhydride in the melt. II. Properties and phase behavior

The Preparation of Mah/St Multi-Monomer Melt Grafting on Abs and Its Compatibilizer Effect on Pa6/Abs Blends

Semicontinuous thermal bulk copolymerization of styrene and maleic anhydride: Experiments and reactor model

Graft Copolymerization of Maleic Anhydride Onto Low‐molecular‐weight Polyisobutylene Through Solvothermal Method

Solvothermal Process for Grafting Maleic Anhydride Onto Poly(ethylene 1-Octene)

Preparation and Characterization of Maleic Anhydride Compatibilized Poly(lactic acid)/Bamboo Particles Biocomposites

Chemically Initiated Graft Copolymerization of Methacrylic Acid Onto Acrylonitrile-Butadiene-Styrene Terpolymer

Grafting of long-chain unsaturated carboxylic acids onto acrylonitrile-butadiene-styrene terpolymer

Study on styrene-assisted melt free-radical grafting of maleic anhydride onto polypropylene

Preparation and application of higher poly (alpha-olefin)-g-maleic anhydride

Synthesis of N-Phenylmaleimide/Styrene/Alpha Methyl Styrene/Maleic Anhydride Tetrapolymers and Its Modification to ABS Resin

Effects of ABS-g-MAH on mechanical properties and compatibility of ABS/PC alloy

Preparation of Amine-Functionalized Compatilizer for PC/ABS Blends

Ultrasound Initiated Maleic Anhydride Grafted Onto a Novel Polypropylene Copolymer

Preparation of PC MABS Alloys by Bulk and Their Properties