Abstract:The present work proposes to investigate the effect of an ultrahigh molecular weight silicone rubber (UHMW-SR) and two ethylene methyl acrylate copolymers (EMA) with different methyl acrylate (MA) content on the mechanical and fire performance of a fireproof acrylonitrile butadiene styrene copolymer (ABS) composite, with an optimum amount of ammonium polyphosphate (APP) and aluminum diethyl phosphinate (AlPi). ABS formulations with a global flame retardant weight content of 20 wt.% (ABS P) were melt-compounded, with and without EMA and UHMW-SR, in a Brabender mixer. During this batch process, ABS P formulations with UHMW-SR and/or EMA registered lower torque values than those of ABS P. By means of scanning electron microscopy (SEM), it was possible to observe that all ABS composites exhibited a homogenous structure without phase separation or particle agglomeration. Slightly improved interfacial interaction between the well-dispersed flame-retardant particles in the presence of EMA and/or UHMW-SR was also noticed. Furthermore, synergies in mechanical properties by adding both EMA and UHMW-SR into ABS P were ascertained. An enhancement of molecular mobility that contributed to the softening of ABS P was observed under dynamic mechanical thermal analysis (DMTA). An improvement of its flexibility, ductility and toughness were also registered under three-point-bending trials, and even more remarkable synergies were noticed in Charpy notched impact strength. Particularly, a 212% increase was achieved when 5 wt.% of EMA with 29 wt.% of MA and 2 wt.% of UHMW-SR in ABS P (ABS E29 S P) were added. Thermogravimetric analysis (TGA) showed that the presence of EMA copolymers in ABS P formulations did not interfere with its thermal decomposition, whereas UHMW-SR presence decreased its thermal stability at the beginning of the decomposition. Although the addition of EMA or UHMW-SR, as well as the combination of both in ABS P increased the pHRR in cone calorimetry, UL 94 V-0 classification was maintained for all flame-retarded ABS composites. In addition, through SEM analysis of cone calorimetry sample residue, a more cohesive surface char layer, with Si-O-C network formation confirmed by Fourier transform infrared (FTIR), was shown in ABS P formulations with UHMW-SR.

Synthesis of N-Phenylmaleimide/Styrene/Alpha Methyl Styrene/Maleic Anhydride Tetrapolymers and Its Modification to ABS Resin

Synthesis and Properties of Styrene-N-Phenylmaleimide-Maleic Anhydride Tercopolymer

Structure and Properties of Heat‐resistant ABS Resins Innovated by NSM Random Copolymer

Research on effect of ABS,MAH,DCP on property of PA6/ABS blend

Modification of acrylonitrile-butadiene-styrene terpolymer by graft copolymerization with maleic anhydride in the melt. II. Properties and phase behavior

Synthesis and Characterization of Heat‐resistant N‐phenylmaleimide–styrene–maleic Anhydride Copolymers and Application in Acrylonitrile–butadiene–styrene Resin

Compatibility and Thermal Properties of Poly(acrylonitrile–butadiene–styrene) Copolymer Blends with Poly(methyl Methacrylate) and Poly(styrene‐co‐acrylonitrile)

Synthesis and Properties of Styrene-co-N-phenylmaleimide Random Copolymers

Synthesis and Characterization of Trifluoromethyl Substituted Styrene Polymers and Copolymers with Methacrylates: Effects of Trifluoromethyl Substituent on Styrene

Investigation of the Properties of PBT/ABS-g-GMA Blends Modified with Epoxy Resin of Mid-Molecular Weights

Effect of Maleic Anhydride Copolymerization Mode on the Properties of PA6/ABS Blends

Synthesis of Acrylonitrile-Butadiene-Styrene Copolymers Through Interface-Initiated Room-Temperature Polymerization

Modification of Acrylonitrile–butadiene–styrene Terpolymer by Grafting with Maleic Anhydride in the Melt. I. Preparation and Characterization

Synthesis of multipolyphosphazene ramification and research on its influence on PC/ABS performance

The Preparation of Mah/St Multi-Monomer Melt Grafting on Abs and Its Compatibilizer Effect on Pa6/Abs Blends

Toughening of Poly(butylene Terephthalate) with Epoxy-Functionalized Acrylonitrile–butadiene–styrene

Enhanced heat resistance of ABS/poly(N-(4-fluorophenyl) maleimide-alt-triallyl isocyanurate) composites based on solid-state interfacial reaction

Preparation and Mechanical Properties of Toughened ABS Resin via Bulk Polymerization

Phosphorus-Based Flame-Retardant Acrylonitrile Butadiene Styrene Copolymer with Enhanced Mechanical Properties by Combining Ultrahigh Molecular Weight Silicone Rubber and Ethylene Methyl Acrylate Copolymer

Synthesis of poly(styrene/maleic anhydride/butyl acrylate)

Influence of Epoxy Resin on the Morphological and Rheological Properties of PBT/ABS Blends Compatibilized by ASMA