Abstract:The aim of this study is to enhance the plasticity and strength of M2 high-speed steel through electron beam melting (EBM) technology. Therefore, by controlling different melting times to change the energy input, a gradient distribution of grain size and uniform distribution of carbides can be achieved. During the deformation process, the gradient structure causes geometrically necessary dislocations (GND) to accumulate near the boundary of regions in the soft zone, resulting in compressive stress in the soft zone and tensile stress in the hard zone, ultimately achieving heterogeneity-induced (HDI) work hardening. This study is to EBM technology for the design and fabrication of three types of M2 high-speed steel samples, denoted as SS-1, SS-2, and SS-3, utilizing three distinct scanning strategies: single melting, double melting, and a combination thereof. The microstructure and phase evolution of these samples were comprehensively characterized using optical microscopy, scanning electron microscopy (SEM), transmission electron microscopy (TEM), and electron backscatter diffraction (EBSD) techniques. The findings demonstrate that when sample SS-3 was subjected to the combined scanning strategy involving both single melting and double melting approaches, its crystal structure exhibited a gradient distribution along with the presence of back stress during tensile testing. Sample SS-3 achieved an average tensile strength of 1479 MPa with an average elongation rate of 1.8%. This represents an enhancement in average tensile strength by approximately 8.6% compared to sample SS-1 (∼1362 MPa) and a significant increase in average elongation rate by around 20% compared to SS-1 (∼1.44%). The gradient grain structure materials show the microstructure transformation from fine grain to coarse-grain in the same material, thus reducing the stress concentration caused by the change of mechanical properties in each region. The SS-3 sample can maintain significant ductility while improving tensile strength. Consequently, this represents a pivotal direction for the advancement of high-performance structural materials. The conducted experimental studies have demonstrated that geometrically necessary dislocations (GNDs) and their associated strain hardening play a crucial role in enhancing the strength of grain structure materials. Additionally, these are essential to achieve an exceptional synergy between strength and toughness in these materials.

Structures and Properties of High-Carbon High Speed Steel by RE-Mg-Ti Compound Modification

Development of Powder Metallurgy High Speed Steel

The Effects of RE-Mg on Thermal Fatigue Resistance of Cast High Speed Steel (HSS) Rolls

Effects of RE/V/Ti Multi-Modification on Grain Refinement of High Silicon Cast Steel

Effects of Ti, V, and Rare Earth on the Mechanical Properties of Austempered High Silicon Cast Steel

Improvement of mechanical property of M2 high-speed steel with hetero-microstructure tailored via electron beam melting

Fracture toughness improvement of austempered high silicon steel by titanium, vanadium and rare earth elements modification

The Effect of Long-Time Austenization on the Wear Resistance and Thermal Fatigue Properties of a High-Speed Steel Roll

Effects of Carbides Distribution in Matrix on Thermal Fatigue and Wear Properties of High Speed Steel Rolls

Study on the Microstructure of Vanadium-Modified Tungsten High-Speed Steel-Coded SAE-AISI T1 Steel

Microstructural Evolution, Behavior of Precipitates, and Mechanical Properties of Powder Metallurgical High-Speed Steel S390 During Tempering

Influence of Re-Ti Modification on the High Impact Wear Resistance of High Si Bainitic Cast Steel

Effect of Deep Cryogenic Time on Martensite Multi-Level Microstructures and Mechanical Properties in AISI M35 High-Speed Steel

Effect of Tungsten Carbide Additions on the Microstructure, Mechanical, and Tribological Properties of M2 High-Speed Steel Matrix Composites

Microstructures and Tribological Properties of TiC Reinforced FeCoNiCuAl High-Entropy Alloy at Normal and Elevated Temperature

Superior fracture toughness in a high-strength austenitic steel with heterogeneous lamellar microstructure

Investigation on the Improvement of Toughness of Complex Modified Medium Manganese Austenitic Steel

Effect of Microstructural Characteristics on Fracture Toughness in Direct Energy Deposited Novel Ti-6Al-4V-1Mo Alloy

Microstructure tailoring and impact toughness of a newly developed high strength Ti-5Al-3Mo-3V-2Cr-2Zr-1Nb-1Fe alloy

Inter-Critically Reheated CGHAZ of Ultra-High-Strength Martensitic Steel with Different Cooling Rates

Microstructure and High-Temperature Tensile Behavior of Modified H13 Steel with the Addition of Tungsten, Molybdenum, and Lowering of Chromium