Abstract:The influence of coating thickness on laser-induced damage (LID) characteristics of anti-reflection (AR) coatings irradiated by 1064 nm nanosecond laser pulses was investigated. Two HfO2/SiO2 AR coatings with different physical thicknesses, 0.7 and 2.7 mu m, were prepared and tested. To study the effect of coating thickness on a laser-induced damage threshold (LIDT) in isolation, electric field intensities (EFIs) at the substrate-coating interface were kept the same by using proper AR designs. Moreover, 2 nm artificial gold particles with a density of 10 mm(-2) were implanted into the substrate-coating interface to achieve reliable experimental results. An optical microscope (OM) and a scanning electron microscope (SEM) were used for an online LIDT test and offline LID morphology observation, respectively. The typical LID morphology of thicker AR coatings was flat bottom craters with diameters of 20-50 mu m, which can be easily observed by an online OM. For thinner AR coatings, hemispherical craters with diameters down to 1 mu m were found as typical LID morphology by a SEM. However, these tiny craters could not be observed by an online OM. Moreover, such tiny craters did not grow with subsequent pulses, so they did not degrade the functional laser damage resistance of the thin AR coatings. When identified with an online OM, the LIDT of thinner AR coatings is found to be about two times higher than the thicker ones, and large delamination was mainly found as the LID morphology of AR coatings with high fluence. When observed with a SEM, the LIDT of thin AR coatings with tiny craters was over 60% lower than the LIDT of thick AR coatings, which agrees with the model that less energy is required to form smaller LID craters of thinner coatings. (C) 2017 Optical Society of America

Study of Al2O3/MgF2 HR Coatings at 355Nm

Effect of multi-waveband antireflective coating on laser induced damage threshold of MgO doped LiNbO3

Numerical Analysis of Thermal Response of Mid-Infrared High Reflectance Coating under Different Laser Irradiation Angles

Laser-induced Heating of Mid-Infrared High Reflectance Coatings

Effect of annealing on the properties of HfO2-Al2O3 mixture coatings for picosecond laser applications

Influence of Deposition Temperature on the Properties of High-Reflectivity Coatings

Effect of annealing on the properties of plasma-enhanced atomic layer deposition grown HfO 2 coatings for ultraviolet laser applications

Effect of annealing on properties and performance of HfO2/SiO2 optical coatings for UV-applications

Study on the Feasibility of Double Stack High Reflector Coating at 355Nm

Influence of Subsurface Defects on 355 Nm Laser Damage Resistance of Monolayer and Multilayer Coatings

Study of Laser Induced Damage of High Reflector at 1064 Nm

LIDT of HfO 2 /sio 2 HR Films by Different Test Modes at 1064nm and 532Nm

Characterization of Laser Induced Damage of HR Coatings with Picosecond Pulses

Laser-induced Damage of TiO2∕SiO2 High Reflector at 1064Nm

Influence of substrate temperature on properties of MgF2 coatings

Comparison of Laser-Induced Damage in Ta2o5 and Nb2o5 Single-Layer Films and High Reflectors

Study For Improvement Of Laser Induced Damage Of 1064 Nm Ar Coatings In Nanosecond Pulse

Improvement on Laser-Induced Damage Threshold of Sol-Gel ZrO_2 Coatings by Crystal Structure Tuning

Nanosecond Laser-Induced Damage of High-Reflection Coatings: Nuv Through Nir

Influence of Coating Thickness on Laser-Induced Damage Characteristics of Anti-Reflection Coatings Irradiated by 1064 Nm Nanosecond Laser Pulses

High Laser-Induced Damage Threshold Antireflection Coatings of 1053 nm Deposited by Ion Assisted Deposition