Atomic structure of high-index a 2 : c m boundaries in a Ti-46.54 at.%Al alloy

J. F. Nie,, W. - Z. Zhang,J. M. Howe,H. I. Aaronson,G. R. Purdy

2003-01-01

Abstract:Abstract

What problem does this paper attempt to address?

Atomic structure of high-index α2:γm boundaries in a Ti–46.54 at.%Al alloy

W.T Reynolds,J.F Nie,W.-Z Zhang,J.M Howe,H.I Aaronson,G.R Purdy

DOI: https://doi.org/10.1016/S1359-6462(03)00307-5

IF: 6.302

2003-01-01

Scripta Materialia

Abstract:Planar, high-index interphase boundaries developed during the α→γm transformation in a Ti–46.54% Al alloy were re-examined with a 3-D near-coincidence site analysis. Pairs of low-index planes, fulfilling the Zhang and Purdy [Philos. Magn. A 68 (1993) 279] minimum mismatch criterion, meet along their edges. Atoms at these edges commingle almost linearly, thereby producing a kinetic barrier to boundary migration.
Electron Structure of Γ/α2 Phase Boundaries in TiAl Based Alloys

Fantao Kong,Ziyong Chen,Yuyong Chen,Jing Tian,Yu-feng SI

2009-01-01

Journal of Material Science and Technology

Abstract:The valence electron structure of γ/α2 phase boundaries in lamellar colonies in Ti-47Al-2M (M=Nb, Cr, V) (at. pct) was investigated by empirical electron theory of solid and molecules (EET) and its bond-length-difference (BLD) method. On this basis, the boundary condition of electron movement was employed in the improved Thomas-Fermi-Dirac (TFD) theory to decide the continuity of the electron density of the lamellar colonies interface and it is found that of γ/α2 interface is continuous. Furthermore, it is found that adding alloying elements (including Nb, Cr, and V) can improve the electron density (ρ) of γ/α2 interface, decrease Aρ of γ/α2 interface. With the electron structure analysis together with properties analysis,the effect mechanism of alloying elements (Nb, Cr, V) improving mechanical properties was explained.
Atomic-scale understanding of the γ/α2 interface in a TiAl alloy

Xiaodong Wang,Yidi Shen,Shuangxi Song,Pan Liu,Qi An,Kolan Madhav Reddy

DOI: https://doi.org/10.1016/j.jallcom.2020.156381

IF: 6.2

2020-12-01

Journal of Alloys and Compounds

Abstract:The eutectoid reaction often produces lamellar structure of two alternating phases, which exhibits promising mechanical properties because of high density interfaces. However, the atomic-level understanding of these interfacial structures remains controversial. Here we report the atomic structure of γ/α2 interface in a fully lamellar TiAl alloy investigated by the aberration corrected transmission electron microscopy and density functional theory (DFT) simulations. The results reveal that the orientation relationship between α2/γ interface in TiAl alloy always follows (0001)α2||{111}γ and 〈11–20〉α2||〈1–10〉γ with a semi-coherent lattice match due to the ultralow interfacial energy predicated by DFT calculation.

materials science, multidisciplinary,chemistry, physical,metallurgy & metallurgical engineering
A Density-Functional Study of Al-Doped Ti Clusters: Tinal (N=1-13)

J Xiang,SH Wei,XH Yan,JQ You,YL Mao

DOI: https://doi.org/10.1063/1.1643713

2004-01-01

Abstract:Equilibrium geometries, stabilities, and electronic properties of TinAl (n = 1-13) clusters have been studied by using density-functional theory with local spin density approximation and generalized gradient approximation. The ground-state structures of TinAl clusters have been obtained. The resulting geometries show that the aluminum atom remains on the surface of clusters for n < 9, but is slowly getting trapped beyond n = 9, meanwhile, the Al atom exhibits a valent transition from monovalent to trivalent. The geometric effects and electronic effects clearly demonstrate the Ti4Al cluster to be endowed with special stability. The studies on the bonds indicate the change from ionic to metalliclike.
Electron structure of γ/α2 phase boundaries in Ti-47 Al-2X (X = Nb, Cr, V) intermetallics

Fantao Kong,Yuyong Chen,Jiecai Han

2005-01-01

Abstract:In this article, the valence electron structure of γ/α2 phase boundaries in lamellar colonies in Ti-47Al-2X(X = Nb, Cr, V) (at%) was investigated by Empirical Electron Theory of Solid and Molecules (EET) and it's the bond-length-difference (BLD) method. It is found that of γ/α2 interfaces in TiAl based alloys are continuous (Δρ < 10%). Furthermore, it is found that adding alloying elements (including Nb, Cr, and V) can improve the electron density (ρ) of (0001)α2 crystal plane and (111)γ crystal plane, and decrease electron density difference (Δρ) of γ/α2 phase boundaries. With the electron structure analysis together with properties analysis, the order of adding elements improving RT mechanics properties in theory is as follows; V>Cr>Nb.
Electron structure of gamma/alpha(2) phase boundaries in TiAl based alloys

FT Kong,ZY Chen,YY Chen,J Tian,YF Si

2003-01-01

Abstract:The valence electron structure of gamma/alpha(2) phase boundaries in lamellar colonies in Ti-47Al-2M (M=Nb, Cr, V) (at. pct) was investigated by empirical electron theory of solid and molecules (EET) and its bond-length-difference (BLD) method. On this basis, the boundary condition of electron movement was employed in the improved Thomas-Fermi-Dirac (TFD) theory to decide the continuity of the electron density of the lamellar colonies interface and it is found that of gamma/alpha(2) interface is continuous. Furthermore, it is found that adding alloying elements (including Nb, Cr, and V) can improve the electron density (rho) of gamma/alpha(2) interface, decrease Deltarho of gamma/alpha(2) interface. With the electron structure analysis together with properties analysis, the effect mechanism of alloying elements (Nb, Cr, V) improving mechanical properties was explained.
An Ab Initio Study on the Electronic Structures of the Solid/liquid Interface Between TiB 2 (0 0 0 1) Surface and Al Melts

H.L. Zhang,Y.F. Han,Y.B. Dai,S.S. Lu,J. Wang,J. Zhang,D. Shu,B.D. Sun

DOI: https://doi.org/10.1016/j.jallcom.2014.07.053

IF: 6.2

2014-01-01

Journal of Alloys and Compounds

Abstract:•Interfacial electronic structures between Al melts and TiB2 surface are investigated.•The Al ordered layer on TiB2 surfaces results from different covalent hybridizations.•The 3d(Ti)–3p(Al) hybridization supports the continuous growth of Al layers.•The weak bonding at the B-terminated interface restricts the structural order.
TEM Characterization of Domain Boundaries in a Ti–46Al–1Cr–0.2Si Alloy

GH Cao,GJ Shen,JM Liu,ZG Liu,W Skrotzki

DOI: https://doi.org/10.1016/s1359-6462(03)00410-x

IF: 6.302

2003-01-01

Scripta Materialia

Abstract:The microstructure of a Ti–46Al–1Cr–0.2Si alloy was investigated by transmission electron microscopy (TEM). It is characterized by a duplex structure consisting of a two-phase γ/α2 lamellar microstructure and single-phase γ grains. In the single-phase γ areas there exist 60°, 120° and 180° domain boundaries. In the lamellar structure the γ and α2 phases obey the relationships: (0001)α2//{111}γ with 〈112̄0〉α2//〈110〉γ. The mechanism of formation of the ordered domains is discussed.
Ti-Ti Bonding in γ-TiAl and f.c.c. Ti

Y. Song,S. P. Tang,J. H. Xu,O. N. Mryasov,A. J. Freeman,C. Woodward,D. M. Dimiduk

DOI: https://doi.org/10.1080/01418639408240267

2006-01-01

Abstract:The flow and fracture of high-temperature intermetallic alloys is strongly influenced by the propagation and cross-slip of ordinary and super dislocations. One factor associated with the poor ductility of TiAl is an apparently large Peierls stress, or lattice friction stress for the glide of ordinary (1/2[110]) dislocations. This Peierls relief is intimately related to the underlying crystal and electronic structure of TiAl, and specific bonding states have been identified by some investigators as contributing to the pinning of dislocations along certain line directions. In this study we qualify the relative strength of these bonds using several complementary electronic structure methods. Aspects of the electronic structure, equilibrium lattice constants and bond energies of gamma-TiAl are compared with hypothetical f.c.c. Ti as obtained by the full-potential linearized augmented-plane-wave (FLAPW) method, the DMol molecular cluster method and the linear muffin-tin orbital (LMTO) Green function (GF) method. Pair energies, bond occupations of Ti-Ti and Ti-Al bonds in L1(0) TiAl and f.c.c. Ti are calculated using the LMTO GF method. Comparing the d(xy) bonding states for these two crystal structure, we find the in-plane directional d-d bonding between Ti atoms on the (001) plane are strengthened in TiAl relative to f.c.c. Ti. These observations suggest that the alternating (001) planes of Al and Ti atoms presented in TiAl enhance these bonding states. Conversely, transition-metal ternary additions substituted on the Al sites in TiAl are expected to weaken these bonding states. Using the FLAPW method, we examine the changes in charge density in the Ti(001) planes when Mn atoms are substituted on Al sites in TiAl. Finally, LMTO GF methods are used to study the effect of Mn substitutional point defects on the Ti(001) d(xy) bonding states.
High-Resolution and Analytic Electron Microscopy Investigations on the Microstructure of A Tial (W, Si) Alloy

R Yu,LL He,ZX Jin,JT Guo,HQ Ye,V Lupinc

DOI: https://doi.org/10.1515/ijmr-2000-910404

2000-01-01

International Journal of Materials Research

Abstract:The microstructure of a Ti-47Al-2W-0.5Si alloy has been investigated using high-resolution electron microscopy and analytical electron microscopy. From the three main phases, i.e. gamma, alpha(2) and B2, many precipitates: are formed. Ti5Si3 particles formed in the equiaxed grains match well with the gamma matrix. A new orientation relationship has been identified between the Ti5Si3 and gamma phase. Due to the stabilizing effect of W, B2 phase is formed in the alloy, and it contains much more W, more Si and shows a higher Ti to Al ratio in comparison with the equiaxed gamma phase. Moreover, the gamma precipitates formed in the B2 phase contain small amounts of W and Si. In the (gamma + alpha(2)) lamellar structure, Ti5Si3 and B2 particles are formed. The Ti5Si3 particles were formed mainly by the dissolution of the preliminary B2 particles. This is atcributed to the enrichment of Si and the Ti to Al ratio in the B2 phase.
Atomic-scale investigation on the interface structure of {2 2 ̅ 01} α2-Ti3Al deformation twins in polysynthetically twinned TiAl single crystals

Neng He,Zhixiang Qi,Yongxin Cheng,Jinpeng Zhang,Lianlong He,Guang Chen

DOI: https://doi.org/10.1016/j.intermet.2020.106995

IF: 4.075

2021-01-01

Intermetallics

Abstract:The interface structure of {2 2 ‾ 01} α2-Ti3Al deformation twins formed during tensile deformation of polysynthetically twinned (PST) TiAl single crystals at 900 °C has been studied systematically by aberration-corrected scanning transmission electron microscopy. Numerous superlattice intrinsic stacking faults (SISFs) are formed on the (0001) basal plane of α2 twins, thereby resulting in the formation of steps on the twin boundaries. The height of steps equals to the spacing of the (2 2 ‾ 01) twinning plane. The basal-plane SISFs formed in α2 twins can't be attributed to the glide of Shockley superpartial dislocations. Lattice correspondence analyses based on classical twinning theory reveal that complex atomic shuffle and interchange shuffling are responsible for the formation of twinning and basal-plane SISFs in α2 twins. In addition, basal-plane antiphase boundaries (APB) are formed at the vicinity of α2 twin tips to relieve the stress concentration imposed by misfit dislocations.

materials science, multidisciplinary,chemistry, physical,metallurgy & metallurgical engineering
Topics on Microstructure Researches in TiAl Intermetallics Using Atomic Scale Observation and Computational Simulation

LL He,LG Zhou,R Yu,L Dong,HQ Ye

2001-01-01

Abstract:TiAl-based alloys have received much attention in recent years since they are primary candidates for high-temperature structure material. In this paper, characterization of atomic structures of TiAl grain boundaries (GBs) and identification of a Ti2Al phase were performed on the atomic scale in combination of experimental observation and computational simulation. Using high-resolution electron microscope (HREM) observation and MS calculation, the atomic structure of an asymmetry large angle tilting GB has been characterized, which was named as a pseudo Sigma 3 (1 (5) over bar(1) over bar) [101] / / (1 (1) over bar1) [110] GB. Based on HREM observation, nano-beam EELS and EDS analysis and ab initio pseudopotential calculation for the cohesive energy of compound, the Ti2Al phase was identified. Its unit cell has the stacking sequences (Al,3Ti)-(Al,3Ti)-(Al,3Ti)-(Al,Ti)-(Al,3Ti)-(Al,Ti) with ABCBB'CB' order, which is different from the reported model.
Investigation of the ordering and atomic site occupancies of Nb-doped TiAl/Ti3Al intermetallics

Tala'at Al-Kassab,Yong Yuan,Christian Kluthe,Torben Boll,Zhi-Guo Liu

DOI: https://doi.org/10.1002/sia.2530

2007-01-01

Surface and Interface Analysis

Abstract:Titanium-aluminum alloys comprising mainly the TiAl-phase and a small amount of the Ti3Al-phase are promising candidates for application as high-temperature materials. Alloying addition of Nb improves clearly the mechanical strength and the oxidation resistance of these alloys. A dual-phase TiAl/Ti3Al alloy with additions of 5 at.%Nb was investigated in this study by means of field-ion microscopy (FIM), tomographic atom probe (TAP) and transmission electron microscopy (TEM). It has been found that the structure of the two phases and the lamellar structure of the alloy were not seriously changed by the addition of 5 at.% Nb. The structural anisotropy of the TiAl phase along [100] and [001] directions, as revealed by FIM, was analyzed. FIM observations and atom probe analyses showed that Nb atoms in TiAl phase preferentially occupy Ti atomic sites. Preliminary reconstruction of the atomic stacking sequence perpendicular to [001] direction of the gamma-TiAl phase from the TAP measurements was demonstrated and is discussed. Copyright (C) 2007 John Wiley & Sons, Ltd.
Atomic Structure of a Sigma=3, {111} Twin-Boundary Junction in a BaTiO3 Thin Film

CL Jia,R Rosenfeld,A Thust,K Urban

DOI: https://doi.org/10.1080/095008399177462

IF: 1.195

1999-01-01

Philosophical Magazine Letters

Abstract:The atomic structure of a multiple-twin-lamella junction in a BaTiO3 film has been investigated by means of high-resolution electron microscopy. The investigation is not based on the direct study of the experimental micrographs but on the study of the quantum-mechanical electron wavefunction emerging from the object. The electron wavefunction is obtained by means of numerical reconstruction procedures which use as input a series of high-resolution micrographs taken from the same object area with different settings of the objective lens defocus. In the observed junction area, four types of twin variant including two groups of nanotwins meet each other, resulting in a complicated boundary structure with a mixture of Sigma = 27 and Sigma = 3 segments. This junction can be regarded as a grain boundary connecting two BaTiO3 hexagonal structure domains composed of two groups of nanotwins. A boundary structure unit is identified in which some of the BaO[110] columns are found to be partially occupied.
Analysis of electron structure of gamma/alpha(2) phase boundaries in ternary TiAl intermetallics

KONG Fan-tao,CHEN Yu-yong

IF: 3.752

2006-01-01

Transactions of Nonferrous Metals Society of China

Abstract:The electron structure of gamma/a(2) phase boundaries in lamellar colonies in Ti-47Al-2M(M=Nb, Cr, V) (mole fraction, %) alloys was theoretically investigated by Empirical Electron Theory of Solid and Molecules (EET) and the bond-length-difference (BLD) method. Average-Atom-Model was employed to calculate valence electron structure of TiAl intermetallics containing site substitution elements. On this basis, the boundary condition of electron movement was employed in the improved Thomas-Fermi-Dirac (TFD) theory to decide the continuity of the electron density of the lamellar colonies interface and it is found that of gamma/alpha(2) interface is continuous(Delta rho < 10%). Furthermore, it is found that adding alloying elements (including Nb, Cr, and V) can improve the electron density (rho) of gamma/alpha(2) interfaces, and decrease the electron density difference(Delta rho) of gamma/alpha(2) interfaces. Adding V element decreasing Delta rho is more remarkable than other site substitution elements. According to electron structure study of gamma/alpha(2) interfaces in Ti-47Al-2M alloys, the added elements improve mechanical properties of the alloy in the following order: V > Cr > Nb.
The Atomic Interfacial Structure Between 02 and Y Phases Within a TiAl Alloy in Lamellar Form

Fang Liu,Guo-zhen Zhu

DOI: https://doi.org/10.1017/s1431927615006649

IF: 4.0991

2015-01-01

Microscopy and Microanalysis

Abstract:Journal Article The Atomic Interfacial Structure between 02 and y Phases within a TiAl Alloy in Lamellar Form Get access Fang Liu, Fang Liu State Key Laboratory of Metal Matrix Composites, School of Materials Science and Engineering, Shanghai Jiao Tong University, Shanghai, 200240, P. R. China Search for other works by this author on: Oxford Academic Google Scholar Guo-zhen Zhu Guo-zhen Zhu State Key Laboratory of Metal Matrix Composites, School of Materials Science and Engineering, Shanghai Jiao Tong University, Shanghai, 200240, P. R. China Search for other works by this author on: Oxford Academic Google Scholar Microscopy and Microanalysis, Volume 21, Issue S3, 1 August 2015, Pages 1171–1172, https://doi.org/10.1017/S1431927615006649 Published: 23 September 2015
Atomic Study On The Ordered Structure In Al Melts Induced By Liquid/Substrate Interface With Ti Solute

h l zhang,y f han,weiwei zhou,y b dai,jiaqi wang,b d sun

DOI: https://doi.org/10.1063/1.4907171

IF: 4

2015-01-01

Applied Physics Letters

Abstract:Atomic ordering in Al melts induced by liquid/substrate interface with Ti solute was investigated by ab initio molecular dynamics simulations and in-situ synchrotron X-ray diffraction. It is predicted that deformed nanoscale ordering Al layers with a rhombohedral-centered hexagonal structure (R (3) over barm space group) instead of the intrinsic fcc structure (Fm (3) over barm space group) form on substrate at temperature above Al liquids. With Al atoms stacking away from the interface, the ordering structure reaches a critical thickness, which inhibits the consecutive stacking of Al atoms on substrates. The locally stacking reconstruction induced by Ti atom relieves the accumulated elastic strain energy in ordered Al layers, facilitating fully heterogeneous nucleation on substrate beyond the deformed ordering Al layer around the melting point. The roles of liquid/substrate interface with Ti solute in the physical behavior of heterogeneous nucleation on substrate were discussed. (C) 2015 AIP Publishing LLC.
Effect of Ti/Al Ratio on the Elemental Partitioning in the Face-Centered Cubic-Based γ-γ′ Dual-Phase High Entropy Alloy Studied by Atom Probe Tomography

Bin Han,Feng He,Linfei Xia,Zhijun Wang,Ji Jung Kai

DOI: https://doi.org/10.3389/fmats.2022.806237

2022-03-07

Frontiers in Materials

Abstract:The effect of Ti/Al ratio on the elemental partitioning in the Ni 2 CoFeCrTi x Al y high entropy alloy was studied by atom probe tomography (APT). The APT results indicate that the γ′ nanoparticles have a composition of (NiCoFeCr) 3 TiAl which is independent of Ti/Al ratio. The effect of Ti/Al ratio on the partitioning behaviors of Fe and Cr are significantly different from that of Co. The decreasing of Ti/Al ratio significantly enhanced the incorporation of Fe and Cr into the γ′ nanoparticles. However, the concentration of Co in the γ′ nanoparticles declined with the decrease of Ti/Al ratio.

materials science, multidisciplinary
Study of the Ti2al Phase and Gb Structures in Tial Intermetallics Using Atomic Scale Observation and Computational Simulation

LL He,LG Zhou,R Yu,HQ Ye

DOI: https://doi.org/10.3321/j.issn:0412-1961.2002.06.008

IF: 1.797

2002-01-01

ACTA METALLURGICA SINICA

Abstract:The investigation of phase structures and defects in material at the atomic scale is now deep going into their physical essence, such as structural stability of the phases, atomistic relax at the interfaces, and so on. In this paper, we choose TiAl-based alloys as an example, because they arc primary candidates for high-temperature structural materials for their low density, high strength and good anti-oxidation property. Based on HREM observation, nano-beam EELS and EDS analysis and ab initio pseudopotential calculation for the cohesive energy of compound, the Ti2A1 phase has been identified. Using HREM observation and molecular dynamics calculation, the atomic structures of symmetrical and asymmetrical tilting grain boundaries have been characterized.
The α2 precipitation from equiaxed γ phase in as-cast Ti-44Al-4Nb-2Cr-0.1B alloy

Yonghao Yu,Hongchao Kou,Fengming Qiang,Lingling Wang,Yuqing Li,Ruifeng Zhao,Jinshan Li

DOI: https://doi.org/10.1016/j.matlet.2020.128978

IF: 3

2021-02-01

Materials Letters

Abstract:This paper presents the novel duplex microstructure in Ti-44Al-4Nb-2Cr-0.1B alloy during the heat-treatment of 1200°C/24h+1300°C/1h/FC, which precipitate two kinds of α2 phases from the equiaxed γ grains. The mechanisms of γ→α2 transformation in equiaxed γ grains were investigated. Two needle-like α2 variants can be observed inside one parent γ grain with the intersection angle of 71.4°. The irregular α2 were preferentially precipitated at γ grain boundaries with large disorientation, nucleated selectively in the γ grain whose {111}γ plane nearly parallel the γ/γ grain boundary, and grew into the neighbor γ grains with no orientation relationship.

materials science, multidisciplinary,physics, applied

Atomic structure of high-index a 2 : c m boundaries in a Ti-46.54 at.%Al alloy

Atomic structure of high-index α2:γm boundaries in a Ti–46.54 at.%Al alloy

Electron Structure of Γ/α2 Phase Boundaries in TiAl Based Alloys

Atomic-scale understanding of the γ/α2 interface in a TiAl alloy

A Density-Functional Study of Al-Doped Ti Clusters: Tinal (N=1-13)

Electron structure of γ/α2 phase boundaries in Ti-47 Al-2X (X = Nb, Cr, V) intermetallics

Electron structure of gamma/alpha(2) phase boundaries in TiAl based alloys

An Ab Initio Study on the Electronic Structures of the Solid/liquid Interface Between TiB 2 (0 0 0 1) Surface and Al Melts

TEM Characterization of Domain Boundaries in a Ti–46Al–1Cr–0.2Si Alloy

Ti-Ti Bonding in γ-TiAl and f.c.c. Ti

High-Resolution and Analytic Electron Microscopy Investigations on the Microstructure of A Tial (W, Si) Alloy

Atomic-scale investigation on the interface structure of {2 2 ̅ 01} α2-Ti3Al deformation twins in polysynthetically twinned TiAl single crystals

Topics on Microstructure Researches in TiAl Intermetallics Using Atomic Scale Observation and Computational Simulation

Investigation of the ordering and atomic site occupancies of Nb-doped TiAl/Ti3Al intermetallics

Atomic Structure of a Sigma=3, {111} Twin-Boundary Junction in a BaTiO3 Thin Film

Analysis of electron structure of gamma/alpha(2) phase boundaries in ternary TiAl intermetallics

The Atomic Interfacial Structure Between 02 and Y Phases Within a TiAl Alloy in Lamellar Form

Atomic Study On The Ordered Structure In Al Melts Induced By Liquid/Substrate Interface With Ti Solute

Effect of Ti/Al Ratio on the Elemental Partitioning in the Face-Centered Cubic-Based γ-γ′ Dual-Phase High Entropy Alloy Studied by Atom Probe Tomography

Study of the Ti2al Phase and Gb Structures in Tial Intermetallics Using Atomic Scale Observation and Computational Simulation

The α2 precipitation from equiaxed γ phase in as-cast Ti-44Al-4Nb-2Cr-0.1B alloy