Abstract:In general, single crystal shape memory alloys exhibit superior shape memory effect and superelasticity when compared to their polycrystalline counterparts. However, it is challenging and costly to prepare a single crystal in traditional ways, such as the Czochralski method and directional solidification technique. Recently, cyclic heat treatment (CHT) has emerged as a facile and cost-effective method to fabricate single crystal by inducing abnormal grain growth. In the present work, we aimed to fabricate Fe-Mn-Al-Cu single crystals utilizing the CHT technique. Single crystal Fe-Mn-Al-Cu shape memory alloys were successfully prepared, and the effect of CHT parameters on abnormal grain growth was investigated. It was revealed that increasing the cooling rate resulted in a non-monotonic response in the maximum grain size, which initially increased and was followed by a subsequent decrease. This behavior was attributed to the subgrain refinement, increase in subgrain misorientation angles, and the narrowing of the low density zones (LDZs) of subgrains. Decreasing the lower temperature of CHT caused similar trends in maximum grain size, due to the increase in subgrain misorientation angle and the expansion of the LDZs. Extending the holding time at the lower temperature of CHT had minimal impact on grain size. Increasing the heating rate of CHT resulted in a reduction in the maximum grain size because of the narrowing of the LDZs. Moreover, the addition of 2 wt% Cu led to a reduction of the maximum grain size, attributing to the decreased solvus temperature of the γ phase as a result of Cu addition. Consequently, the γ phase and subgrains were refined, and the LDZs were narrowed.

Temperature Memory Effect in CuAlNi Single Crystalline and CuZnAl Polycrystalline Shape Memory Alloys

Temperature Memory Effect of Ti-Ni-Cu Shape Memory Alloy

Temperature Memory Effect Induced by Incomplete Transformation in Tini-Based Shape Memory Alloy

Temperature Memory Effect of Ni47Ti44Nb9 Wide Hysteresis Shape Memory Alloy

Incomplete Transformation of Ti-Ni-X Ternary Shape Memory Alloy

Martensitic Transformation and Shape Memory Effect of NiCoMnSn High Temperature Shape Memory Alloy

Transformation Behaviour with Thermal Cycling in Ti50Ni43Cu7 Shape Memory Alloy

Effect of Heating/Cooling Rate on the Transformation Temperatures in Tinicu Shape Memory Alloys

Fabrication of single-crystal Fe-Mn-Al-Cu alloys by cyclic heat treatments

Thermal Cycling Effect In Cu-11.9al-2.5mn Shape Memory Alloy With High M-S Temperature

Study on Aging Effect and Mechanism of Cu-11.1Al-6.5Mn-1.6Zn-0.1Zr Shape Memory Alloy

Effect of heat treatment on shape memory properties of ductile CuAlMn alloys

Effect of Cu content on martensitic transformation and shape memory behavior in Ti31.5Hf15Zr5Ni48.5−xCux alloys

Shape memory effect of the Ni-Ti-Hf high temperature shape memory alloy

Mechanical and Thermal Behavior of Cu84−xAl13Ni3Hfx Shape Memory Alloys

Microstructure of martensitic phase in the Co39Ni33Al28 shape memory alloys revealed by transmission electron microscopy

Effect of Homogenization on the Transformation Temperatures and Mechanical Properties of Cu15Ni35Hf12.5Ti25Zr12.5 and Cu15Ni35Hf15Ti20Zr15 High-Entropy Shape Memory Alloys

Effect of Cooling Rate on Microstructure, Shape Memory Effect and Mechanical Properties of Cu–13Al–5Fe High-Temperature Shape Memory Alloy Fabricated by Laser Powder Bed Fusion

Effect of Al content on thermal stability, shape memory effect and mechanical properties of Cu–Al–Fe shape memory alloys

Fe–Mn–Si–Cr–Ni Based Shape Memory Alloy: Thermal and Stress-Induced Martensite

Zr50Cu25Ni7.5Co17.5 high-temperature shape memory alloy with excellent thermal stability and large recovery strain, and the associated microstructural deformation mechanism