Abstract:The demand for advanced Al-based alloys with tailored structural and magnetic properties has intensified for applications requiring a high thermal stability and performance under challenging conditions. This study investigated the phase evolution, magnetic properties, thermal stability, and microstructural changes in the Al-based alloys Al82Fe16Nb2 and Al82Fe14Nb2Mn2, synthesized via mechanical alloying (MA), using stearic acid as a process control agent. The X-ray diffraction results indicated that Al82Fe16Nb2 achieved a β-phase solid solution with 13–14 nm crystallite sizes after 5 h of milling, reaching an amorphous state after 10 h. In contrast, Al82Fe14Nb2Mn2 formed a partially amorphous structure within 10 h, with enhanced stability with additional milling. Magnetic measurements indicated that both alloys possessed soft magnetic behavior under shorter milling times (1–5 h) and transitioned to hard magnetic behavior as amorphization progressed. This phenomenon was associated with a decrease in saturation magnetization (Ms) and an increase in coercivity (Hc) due to structural disorder and residual stresses. Thermal stability analyses on 10 h milled samples conducted via differential scanning calorimetry showed exothermic peaks between 300 and 800 °C, corresponding to phase transformations upon heating. Post-annealing analyses at 550 °C demonstrated the presence of phases including Al, β-phase solid solutions, Al13Fe4, and residual amorphous regions. At 600 °C, the Al3Nb phase emerged as the β-phase, and the amorphous content decreased, while annealing at 700 °C fully decomposed the amorphous phases into stable crystalline forms. Microstructural analyses demonstrated a consistent reduction in and homogenization of particle sizes, with particles decreasing to 1–3 μm in diameter after 10 h. Altogether, these findings highlight MA's effectiveness in tuning the microstructure and magnetic properties of Al–Fe–Nb (Mn) alloys, making these materials suitable for applications requiring a high thermal stability and tailored magnetic responses.

Mechanical activation of barium aluminate formation from BaCO3–Al2O3 mixtures

Preparation of SrAl2O4 from an oxide mixture via a high-energy ball milling

Preparation of Nb3al by High-Energy Ball Milling and Superconductivity

Barium titanate derived from mechanochemically activated powders

Effect of CeO_2 and ZrO_2 Additives on Microstructure and Thermal Stability of High-Energy Ball Milling Al_2O_3 Powder

On Advancemeat of Carbothermal Reduction of Alumina by High Energy Ball Milling

Effect of Mechanical Activation on TiC Synthesis Reaction in Al-Ti-C Powder Mixture

Nano-sized amorphous alumina particles obtained by ball milling ZnO and Al powder mixture

High Temperature Thermal Stability of Al2O3 Modified by BaO

Formation of Nanocrystalline Fcc Phase by Mechanically Driven Crystallization

Amorphization in the AlC System by Mechanical Alloying

INFLUENCE OF MECHANICAL ACTIVATION ON REACTION ACTIVATION ENERGY OF Al-Ti-C POWDER MIXTURE IN SYNTHESIS PROCESS

Phase Transformation and Gas–solid Reaction of Al2O3 During High-Energy Ball Milling in N2 Atmosphere

Solid State Reaction Mechanism and Microstructure Evolution of Ni-Al Powders during High Energy Ball Milling Revisited by TEM

Effect of ball milling treatment on the microstructures and properties of Cr2AlC powders and hot pressed bulk ceramics

Preparation of α-Al2O3 by low-temperature calcining γ-Al2O3 with α-phase seed in-situ obtained by ball milling

Nanocrystalline/Amorphous Tuning of Al–Fe–Nb (Mn) Alloy Powders Produced via High-Energy Ball Milling

Effect of Composition of Initial Powder Mixtures on Solid State Reduction Reaction During High-Energy Ball Milling

Influence of high-energy ball-milling duration on Nb-Al powder mixture microhardness

Effect of Mechanical Activation on the Morphology and Microstructure of Ni-Al-Ti-B Composite Powders

Influence of Parameters of High-Energy Ball Milling on the Synthesis and Densification of Magnesium Aluminate Spinel