Abstract:High molecular weight polyether polyols are widely used. However, there is not only a large risk of reaction heat, but also a long reaction time in its traditional production process by using the semi-continuous reactor. The microchannel reactor（MCR） has the characteristics of high heat transfer efficiency and process safety,but the viscous material and high reaction heat release make it difficult to produce the high molecular weight polyether polyols. In this work, using double metal complex（DMC） as catalyst and n-hexane as solvent, the ringopening polymerization of propylene oxide（PO） was carried out in MCR. Polypropylene glycol（PPG） with molecular weight ranging from 2000 to 8000 was prepared. Effects of reaction conditions, such as flow rate, channel length,reaction temperature and feed policy, were investigated. It has been found that when the residence time is long enough, the molecular weight of the produced PPG is basically equal to the theoretical molecular weight. When the flow rate of initiator is fixed, an increase in flow rate of monomer will result in the molecular weight distribution（MWD） first widened and then narrowed. If the tube length is longer, the molecular weight is larger and the MWD is wider. If the temperature increases, the induction period of the polymerization can be shortened. Using the segmented feed, it is easier to prepare high molecular weight PPG with higher conversion than using the single feed, but the MWD is wider. These rules can be explained from the mechanism of PO ring-opening polymerization catalyzed by DMC and micro-mixing strength of materials in MCR. The lower the micro-mixing strength, and the smaller the rate ratio of chain transfer to chain propagation in polymerization, the wider the molecular weight distribution is.

Microwave-assisted ring-opening polymerization ofp-dioxanone

Preparation of high molecular weight polypropylene glycol in microchannel reactor

Record Productivity And Unprecedented Molecular Weight For Ring-Opening Copolymerization Of Epoxides And Cyclic Anhydrides Enabled By Organoboron Catalysts

Controllable Ring-opening Polymerization of Δ-Valerolactone Catalyzed by Quinolinyl-Urea/MTBD Systems

Ring-Opening Polymerization of Propylene Oxide by Double Metal Complex in Micro-Reactor

Ring-Opening Polymerization of Diisopropyl Cyclopropane-1,1-dicarboxylate under Living Anionic Conditions: A Kinetic and Mechanistic Study

Molecular Weight Distribution in Ring‐Opening Polymerization of Propylene Oxide Catalyzed by Double Metal Complex: A Model Simulation

Ring-Opening Polymerization of 1,4-Dioxan-2-one Initiated by Lanthanum Tris(2,6-Di-Tert-Butyl-4-Methylphenolate)

Synthesis And Solution Self-Assembly Of Poly(1,3-Dioxolane)

Easy Access to Ultrahigh-Molecular Weight Poly(1,3-dioxolane) by Rare Earth Triflates

RING-OPENING POLYMERIZATION OF l,4-DIOXAN-2-ONE INITIATED BY LANTHANUM TRIS(2,6-DI-TERT-BUTYL-4-METHYLPHENOLATE)

Poly(ether ester) and related block copolymers via organocatalytic ring‐opening polymerization

Polymerization of 2,6-Dimethylphenol by Oxidative Coupling Mechanism in Aqueous Medium

Single Lanthanum Tris(N-Phenylethyl-3,5-Di-T-Butylsalicylaldiminato)S Initiator for Ring-Opening Polymerization of 1,4-Dioxan-2-one in Bulk

Synthesis and Characterization of Α,ω-Bis(2,6-dimethylphenol)-poly(2,6-dimethyl-1,4-phenylene Oxide) Oligomers in Water and the End-Group Modification

Microwave Enhanced Catalytic Hydration of Acrolein to 3-Hydroxypropionaldehyde Using Simultaneous Cooling: Experimental and Theoretical Studies

One-pot and One-step Cu(0)-mediated Reversible-Deactivation Radical Polymerization of N -Isopropylacrylamide (NIPAM) in Water

Microwave-assisted regioselective olefinations of cyclic mono- and di-ketones with a stabilized phosphorus ylide

Ring‐opening Polymerization of 1,4‐oxathian‐2‐one and Its Copolymerization with Δ‐valerolactone

Cationic Ring-opening Polymerization of Substituted Oxetane Monomers

Ring-opening Polymerization of Propylene Oxide Catalyzed by Fe-Zn Double Metal Cyanide Catalyst and Its Synthesis