Abstract:Conventional polymers have typically been used in the packaging of various electronic devices; however, due to the inherent electrically insulating properties these materials fail to dissipate static charges. To address this issue, novel poly(ether- b -amide) (PEBA) segmented copolymers consisting of uniform rigid oxalamide and flexible polyethylene glycol (PEG) were synthesized via melt polycondensation. The influence of PEG molecular weight and the spacer length separating two oxalamide units on the condensed structure, mechanical performance, and antistatic properties was systematically investigated. Fourier-transform infrared (FTIR) demonstrated strongly hydrogen bonded and highly ordered oxalamide hard segments with the degree of ordering between 71 and 85 % even at low levels. Mechanical behavior results showed that segmented copolymers have an obvious yield point, an elastic modulus between 20 and 30 MPa, and strain at break exceeding 2000 %. Meanwhile, such copolymers possessed low surface resistivity, as low as 10 7 Ω, which is significantly less than that of commercial antistatic additives. The antistatic effect of PEBA on polyamide 6 (PA6) was also investigated, revealing that when the content reached 30 wt%, the surface resistivity of the alloys decreased from 10 13 Ω to 10 11 Ω and remained stable after 40 days, even after water washing treatment. Overall, these findings illustrate that the newly synthesized PEBA copolymers demonstrate outstanding long-term antistatic properties and provide valuable insights for the development of polyether-based multiblock copolymer antistatic agents.

PREPARATION OF PERMANENT ANTI-STATIC PA6/ABS ALLOY

Research on effect of ABS,MAH,DCP on property of PA6/ABS blend

The preparation of permanent antistatic additive based on poly(ether- b -amide) copolymers and its modification effect on polyamide 6

Preparation of a Novel Stabilizer and Its Thermal‐oxidative Stabilization Effect on Polyamide 6

Creating Super-Tough and Strong PA6/ABS Blends Using Multi-Phase Compatibilizers

Effect of Maleic Anhydride Copolymerization Mode on the Properties of PA6/ABS Blends

Preparation of Amine-Functionalized Compatilizer for PC/ABS Blends

Blending ABS resin and its effect on structure and properties of PC/ABS BLEND alloy

Research on high quality PC/ABS alloy

MORPHOLOGY AND MECHANICAL PROPERTIES OF NYLON-6/ABS POLYMER BLENDS COMPATIBILIZED BY STYRENE-MALEIC ANHYDIDE COPOLYMER

THE STUDY OF APPLIED BEHAVIOR OF PP/PA6 BY USING GRAFTED POLYPROPYLENE AS COMPATILIZER

Relationship between structure and properties in high-performance PA6/SEBS-g-MA/(PPO/PS) blends: The role of PPO and PS

The Preparation of Mah/St Multi-Monomer Melt Grafting on Abs and Its Compatibilizer Effect on Pa6/Abs Blends

Toughening of PA6 with MAH Functionalized Acrylate-styrene-acrylonitrile Copolymer

Effect of Reactive Group Types on the Properties of Core-Shell Modifiers Toughened PA6

Construction of Core‐Shell Structure in PA6/ABS/SEBS Blends for Achieving Stiffness‐Toughness Balance

Modification of the Grafting Character to Prepare PA6/ABS-g-MA Blends with Higher Toughness and Stiffness

Study on Flame-retardant PC/ABS Alloy with High-Strength and Heat-resistance

Morphology and Mechanical Properties of Nylon 6/PBT Blends Compatibilized with Styrene/Maleic Anhydride Copolymer

Effect of ABS types on the morphology and mechanical properties of PA6/ABS blends by in situ reactive extrusion

Preparation and performance study of POE-g-MAH/GMA toughened bio-based PA56 alloys