Abstract:Semi-solid thixoforming processes rely on a material microstructure made of globular solid grains more or less connected to each other, thus developing a solid skeleton deforming into a liquid phase. During processing, the material structure changes with the processing history due to the agglomeration of the particles and the breaking of the grains bonds. This particular evolutive microstructure makes semi-solid materials behave as solids at rest and as liquids during shearing, which causes a decrease of the viscosity and of the resistance to deformation while shearing. Thixoforming of aluminum and magnesium alloys is state of the art and a growing number of serial production lines are in operation all over the world. But there are only few applications of semi-solid processing of higher melting point alloys such as steel. This can partly be attributed to the high forming temperature combined with the intense high temperature corrosion that requires new technical solutions. However the semi-solid forming of steels reveals high potential to reduce material as well as energy consumption compared to conventional process technologies, such as casting and forging. Simulation techniques exhibit a great potential to acquire a good understanding of the semi-solid material process. Therefore, this work deals with the development of an appropriate constitutive model for semi-solid thixoforming of steel. The constitutive law should be able to simulate the complex rheology of semi-solid materials, under both steady-state and transient conditions. For example, the peak of viscosity at start of a fast loading should be reproduced. The use of a nite yield stress is appropriate because a vertical billet does not collapse under its own weight unless the liquid fraction is too high. Furthermore, this choice along with a non-rigid solid formalism allows predicting the residual stresses after cooling down to room temperature. Several one-phase material modeling have been proposed and are compared. Thermomechanical modeling using a thermo-elasto-viscoplastic constitutive law has been developed. The basic idea is to extend the classical isotropic hardening and viscosity laws to the non solid state by considering two non-dimensional internal parameters. The rst internal parameter is the liquid fraction and depends on the temperature only. The second one is a structural parameter that characterizes the degree of structural build up in the microstructure. Those internal parameters can depend on each other. The internal parameters act on the the viscosity law and on the yield surface evolution law. Di erent formulations of viscosity and hardening laws have been proposed and are compared to each other. In all cases, the semi-solid state is treated as a particular case, and the constitutive modeling remains valid over the whole range of temperature, starting from room temperature to above the liquidus. These models are tested and illustrated by mean of several representative numerical applications.

Meniscus Dynamics and Melt Solidification in the EFG Silicon Tube Growth Process

Thermal And Dynamics Analysis Of Meniscus-Controlled Materials Processing

Meniscus Dynamics in Material Processing

Investigation of the Effect of 3D Meniscus Geometry on Fluid Dynamics and Crystallization via In Situ Optical Microscopy‐Assisted Mathematical Modeling

Numerical Studies of Semiconductor Materials Solidification With Applied Electric and Magnetic Fields

Modelling of Meniscus Behavior and Slag Consumption During Initial Casting Stage of Continuous Casting Process

Experimental Study Of Buckling Behavior Of Octagonal Thin Walled Silicon Tube Grown By Edge-Defined Film-Fed Method

Lumped-Parameter Modeling For Meniscus Dynamic Analysis In Immersion Flow Field

Direct Numerical Simulation of Solid Deformation During Dendritic Solidification

Electrical-thermal-mechanical coupled modeling and simulation on deformation behaviors of Ti6554 alloy in electrically-assisted micro-tension

Numerical Analysis of Particulate Migration Behavior Within Molten Pool During TIG-Assisted Droplet Deposition Manufacturing of SiC Particle-Reinforced Aluminum Matrix Composites.

A Mechanics-Based Phase-Field Model and Finite Element Simulations for Microstructure Evolution during Solidification of Ti-6Al-4V

Simulation Study on Transient Periodic Heat Transfer Behavior of Meniscus in Continuous Casting Mold

Numerical Simulation Of Asymmetrical Fluid Flow And Solidification During The Electron Beam Cold Hearth Re-Melting (Ebchr) Process Of Titanium Alloy Ta10

Simulation of dendritic-eutectic growth with the phase-field method

Three Dimensional Numerical Simulation of Solidification Microstructure of Single Phase Alloy

Effect of upper surface characteristics on meniscus stability in immersion flow field

A Theoretical Model of the Shrinking Metal Tubes

Semi-solid constitutive modeling for the numerical simulation of thixoforming processes.

Technology and Thermomechanics in Growing Tubular Silicon Single Crystals

Simulation and Experimental Study of Fluid Flow and Solidification Behavior in Thin Slabs Continuous Casting Process under Secondary Electromagnetic Stirring