Abstract:Corner cracks are one of the most widespread surface defects of continuous casting slabs, and they are especially severe for peritectic steels and low-alloy steels. Therefore, a clear understanding of molten steel initial solidification around mold corner would be of great importance for the inhibition of corner cracks. This paper has been conducted with the aim to elucidate this understanding, by using a novel mold simulator equipped with a right-angle copper mold. The responding temperatures and heat fluxes across the mold hot-face and corner were firstly calculated through a 2D-inverse heat conduction program mathematical model, and the results suggested that the cooling ability and the fluctuation of heat fluxes around the mold corner are stronger than those for mold hot-face. With the help of power spectral density analysis and fast Fourier transformation, the four characteristic signals of heat fluxes were discussed in this paper. Next, the relation between the thickness of solidified shell and solidification time was fitted with the solidification square root law; as a result, the average solidification factor \( \bar{K} \) for the hot-face shell is 2.32 mm/s1/2, and it is 2.77 mm/s1/2 for the shell near-corner. For the same oscillation marks (OMs), it appeared that the OMs positions on the shell corner are lower than those on the shell hot-face along the casting direction, because the stronger shrinkage of shell at the corner allows the overflowing steel to penetrate deeper into the larger gap between the shell corner and mold, which is demonstrated through the heat transfer analysis and metallographic examination. Finally, the interrelation between shell profile, mold oscillation, variation rate of heat flux, high-frequency heat flux and high-frequency temperature was discussed for above two cases, and the results suggested that meniscus conditions (heat transfer and melt flow) around the mold corner are more unsteady.

Simulation Study on Transient Periodic Heat Transfer Behavior of Meniscus in Continuous Casting Mold

A 3D Mathematical Modeling on Meniscus Solidification and Heat Transfer in Continuous Casting Chamfered Mold of Slab

Modelling of Meniscus Behavior and Slag Consumption During Initial Casting Stage of Continuous Casting Process

Mold Simulator Study of the Initial Solidification of Molten Steel in Continuous Casting Mold: Part II. Effects of Mold Oscillation and Mold Level Fluctuation

Mold Simulator Study of the Initial Solidification of Molten Steel in Continuous Casting Mold. Part I: Experiment Process and Measurement

Mold Simulator Study of Heat Transfer Phenomenon During the Initial Solidification in Continuous Casting Mold

A coupled model on fluid flow, heat transfer and solidification in continuous casting mold

Study of Meniscus Shape in Mold of Medium-Frequency Soft-Contact Electromagnetic Continuous Casting for Round Billets

Transient flow and mold flux behavior during ultra-high speed continuous casting of billet

Study on Behavior of Slag Rim and Shell Initial Solidification at Meniscus in Continuous Casting Slab Mold

Variation of Meniscus Shape and Initial Steel Solidification under Different Steel–slag Interfacial Tension in Continuous Casting Mold of Slab

Mold Simulator Study on the Initial Solidification of Molten Steel Near the Corner of Continuous Casting Mold

Dynamic Meniscus Behavior Influencing on Surface Condition of Products Cast in Continuous Caster with Alternating Magnetic-Field Applied from the Outside of A Mold

Analysis of Non-uniform Mechanical Behavior for a Continuous Casting Mold Based on Heat Flux from Inverse Problem

Modeling and Simulation of Multi-phase and Multi-physical Fields for Slab Continuous Casting Mold under Ruler Electromagnetic Braking

Simulation of Coupled Fluid Flow, Heat Transfer and Solidification in Slab Continuous Casting Molds Based on Heat Flux from an Inverse Model

3D Coupled Model on Dynamic Initial Solidification and Slag Infiltration at the Corner of Slab Continuous Casting Mold

Simulation of Molten-steel Flow Fields in a Continuous Slab Casting Mold

A Study for Initial Solidification of Sn-Pb Alloy During Continuous Casting: Part I. the Development of the Technique

Heat transfer behavior in ultrahigh-speed continuous casting mold

Thermal simulation on meniscus motion in the continuous casting with multi-electromagnetic field