Abstract:The passive safety commercial pressurized water reactors (PWRs), AP1000 and CAP1400 are equipped with the automatic depressurization system (ADS). The fourth stage of ADS (ADS-4) has the largest discharging capacity among the all ADS stages. During a small break loss-of-coolant accident (SBLOCA), only when the system is fully depressurized by the ADS-4 to near the containment atmospheric pressure, the in-containment refueling water storage tank (IRWST) can deliver the large coolant inventory for the long-term core cooling by its water head. Before the IRWST injection, the core reaches its minimum inventory. So the transition from the ADS-4 depressurization to the IRWST injection is a very challenging period in a SBLOCA. Therefore, to evaluate the passive system performance by the integral effect test (IET), the transition must be simulated properly. This work conducted the scaling analysis for the ADS-4 depressurization and the IRWST injection for designing the related components of the ACME IET facility. A uniform scaling law based on the existing T-branch liquid entrainment models was proposed. For scaling the onset of the IRWST injection, the requirement for reproducing the synergetic effect in an IET was introduced in order to preserve the important event/process occurrence time with the proper conditions, and the scaling laws for the full pressure IRWST injection were obtained. For investigating the transition thermal hydraulic behaviors and the ADS-4 configuration influences on the core safety, one cold leg break test and three double-ended direct-vessel-injection (DEDVI) line break tests with the different ADS-4 failure modes were selected from the ACME SBLOCA test matrix, and the main test data related to the core safety were analyzed and compared. It was found that the ADS-4 actuation significantly accelerated the system depressurization but worsened the core inventory depletion at the same time. In addition, the break condition and the ADS-4 failure mode could differently affect the system depressurization and the core level. The ACC injection during the ADS-4 depressurization in DEDVI was critical for the core level makeup. The insufficient ADS-4 venting capacity delayed IRWST injection, but also mitigated the core inventory depletion. It suggests the ADS-4 design can be potentially optimized in the passive safety system design. (C) 2019 Elsevier Ltd. All rights reserved.

Similarity Analysis for Reduced Pressure Test on Depressurization Phase during Pressurized Water Reactor Loss of Coolant Accident

Scaling Analysis of the Pressurizer Surge Line in Nuclear Plant Integral Test Facilities

Stored Energy Analysis in the Scaled-Down Test Facilities

A Transient Fluid–structure Interaction Analysis Strategy and Validation of a Pressurized Reactor with Regard to Loss-of-coolant Accidents

Pressure Reducing and Loss of Water under SBLOCA at Upper Plenum of Nuclear Heating Reactors

Liquid Collapse Level Monitoring for Nuclear Reactors During Loss of Coolant Accident

DESIGN AND DISTORTION ANALYSIS OF THERMAL-HYDRAULICS TEST FACILITY FOR THE FUEL TRANSFER TUBE

Scaling methodologies and similarity analysis for thermal hydraulics test facility development for water-cooled small modular reactor

Analysis on Working Pressure Selection of ACME Integral Test Facility

Study of Depressurization Process for Supercritical Fluid

Research on Scaling Analysis and Design Parameters of Integral Test Facilities for PWR

Experimental Simulation Analysis of ADS-4 Entrainment and Depressurization in AP1000

Analysis Method for LOFT L2-5 LBLOCA Experiment

Analysis on Cooling Capacity of Passive Core Cooling System during LOCA Scenarios

Scaling and Integral Effect Test on Transition from Depressurization to Long-Term Gravity Injection

Analysis of LOCA with different break sizes in PWR

The Numerical Simulation Research of Gas–Liquid Two-Phase Flow in Small-Break Loss-of-Coolant Accidents

Thermal Hydraulic and Stress Coupling Analysis for AP1000 Pressurized Thermal Shock (PTS) Study under SBLOCA Scenario

Feasibility Test for Reactor Coolant System Optimized Design Scheme

Study on the Reactor Core Barrel Instantaneous Characteristics in Case of Loss of Coolant Accident (LOCA) Scenarios for Loop-Type PWR

A SIMULATION OF SMALL BREAK LOSS OF COOLANT ACCIDENT IN NUCLEAR HEATING REACTOR BASED ON RELAP5