Abstract:The passive safety commercial pressurized water reactors (PWRs), AP1000 and CAP1400 are equipped with the automatic depressurization system (ADS). The fourth stage of ADS (ADS-4) has the largest discharging capacity among the all ADS stages. During a small break loss-of-coolant accident (SBLOCA), only when the system is fully depressurized by the ADS-4 to near the containment atmospheric pressure, the in-containment refueling water storage tank (IRWST) can deliver the large coolant inventory for the long-term core cooling by its water head. Before the IRWST injection, the core reaches its minimum inventory. So the transition from the ADS-4 depressurization to the IRWST injection is a very challenging period in a SBLOCA. Therefore, to evaluate the passive system performance by the integral effect test (IET), the transition must be simulated properly. This work conducted the scaling analysis for the ADS-4 depressurization and the IRWST injection for designing the related components of the ACME IET facility. A uniform scaling law based on the existing T-branch liquid entrainment models was proposed. For scaling the onset of the IRWST injection, the requirement for reproducing the synergetic effect in an IET was introduced in order to preserve the important event/process occurrence time with the proper conditions, and the scaling laws for the full pressure IRWST injection were obtained. For investigating the transition thermal hydraulic behaviors and the ADS-4 configuration influences on the core safety, one cold leg break test and three double-ended direct-vessel-injection (DEDVI) line break tests with the different ADS-4 failure modes were selected from the ACME SBLOCA test matrix, and the main test data related to the core safety were analyzed and compared. It was found that the ADS-4 actuation significantly accelerated the system depressurization but worsened the core inventory depletion at the same time. In addition, the break condition and the ADS-4 failure mode could differently affect the system depressurization and the core level. The ACC injection during the ADS-4 depressurization in DEDVI was critical for the core level makeup. The insufficient ADS-4 venting capacity delayed IRWST injection, but also mitigated the core inventory depletion. It suggests the ADS-4 design can be potentially optimized in the passive safety system design. (C) 2019 Elsevier Ltd. All rights reserved.

Analysis of a test facility for transients in a supercritical water-cooled reactor using dynamic system scaling methodology

Study of Depressurization Process for Supercritical Fluid

Scaling methodologies and similarity analysis for thermal hydraulics test facility development for water-cooled small modular reactor

Thermal-hydraulic Analysis of SWAMUP Test Facility

Scaling-up assessment of natural circulation phenomena in integral Small Modular Reactor by TRACE code

Fluid-to-fluid Scaling of Heat Transfer in Circular Tubes Cooled with Supercritical Fluids

Development of a Transient Analysis Code for Trans-Critical Simulation of SCWR

Thermal-Hydraulic Analysis of SWAMUP Facility Using ATHLET-SC Code

Investigation of the Safety Limits and the Limiting Safety System Settings on a Super Carbon-Dioxide Cooled Micro Modular Reactor

A New Method on Fluid-to-fluid Scaling for Heat Transfer in Tubes at Supercritical Pressures

Multi-scale Thermal-Hydraulics Analysis on SCWR Fuel Qualification Test Loop

Dynamic modeling and validation of the 5 MW small modular supercritical CO2 Brayton-Cycle reactor system

Scaling analysis and design for PCS air flow path natural circulation

Scaling Analysis of the Pressurizer Surge Line in Nuclear Plant Integral Test Facilities

Sensitive Analysis of Heat Transfer Model During Trans-critical Depressurization

Review, numerical validation, and experiment verification for Definite solution Analogy Theory (DSAT) in thermal-hydraulic scaling

The Dynamical System Scaling Analysis for Single-Phase Integral Test Facilities

Scaling and Integral Effect Test on Transition from Depressurization to Long-Term Gravity Injection

Transient Three-Dimensional Stability Analysis of Supercritical Water Reactor Rod Bundle Subchannels by A Computatonal Fluid Dynamics Code

Scaling for Different Containment Passive Cooling Design under LOCA Conditions

Assessment of Scaling Distortion in Condensation Film Heat Transfer