Abstract:Bubble growth processes are highly complex processes, which are not only dependent on the foaming process parameters (temperature, pressure and blowing agent concentration) but also on the type and structure of the polymer used. Since the elongational viscosity at the bubble wall during bubble growth also depends on these influencing factors, the so-called transient elongational viscosity plays a key role in describing the gas bubble growth behavior in polymer melts. The model-based description of the transient elongational viscosity function is difficult due to its dependence on time, Hencky strain and strain rate. Therefore, representative viscosities or shear viscosity models are usually used in the literature to predict the bubble growth behavior. In this work, the transient equibiaxial elongational viscosity function at the bubble wall during bubble growth is described holistically for the first time. This is achieved by extending the so-called molecular stress function (MSF) model by superposition principles (temperature, pressure and blowing agent concentration) and by using the elongational deformation behavior (Hencky strain and strain rate) at the bubble wall during the initial, and thus viscosity-driven, bubble growth process. Therefore, transient uniaxial elongational viscosity measurements are performed and the non-linear MSF model parameters of the two investigated polymers PS (linear polymer chains) and PLA (long-chain branched polymer chains) are determined. By applying the superposition principles and by changing the strain mode parameter to the equibiaxial case in the MSF model, the transient equibiaxial viscosity master curve is obtained and used to describe the bubble growth process. The results show that the extended MSF model can fully predict the transient equibiaxial elongational viscosity function at the bubble wall during bubble growth processes. The bubble growth behavior over time can then be realistically described using the defined transient equibiaxial elongational viscosity function at the bubble wall. This is not possible, for example, with a representative viscosity and therefore clearly demonstrates the influence and importance of knowing the transient deformation behavior that prevails at the bubble wall during bubble growth processes.

Plasticization effects on bubble growth during polymer foaming

Effect of Melt Viscosity on the Cell Morphology and Properties of Poly(lactic Acid) Foams

Accurate Determination of Bubble Size and Expansion Ratio for Polymer Foaming with Non-Isothermal PBB Model Based on Additional Energy Conservation

Effect of Additives on the Dynamic Bubble Growth Behavior of Polymer Foam Evaluated with In-Situ Visualizations and Simulations

Numerical simulation of polypropylene foaming process assisted by carbon dioxide: Bubble growth dynamics and stability

Prediction of the Bubble Growth Behavior by Means of the Time-, Temperature-, Pressure- and Blowing Agent Concentration-Dependent Transient Elongational Viscosity Function of Polymers

Study on the definition, mechanism and controllability of secondary bubbles based on the bubble nucleation model in injection foaming polypropylene

The effect of plastic rearrangements on the flow of two-dimensional wet foam.

Rheological Properties of Thermoplastic Polymers with Dissolved Gases for Foaming Applications

Effect of Plasticizer on the Morphology and Foaming Properties of Poly(vinyl alcohol) Foams by Supercritical CO2 Foaming Agents

Analysis of Bubble Growth in Supercritical CO2 Extrusion Foaming Polyethylene Terephthalate Process Based on Dynamic Flow Simulation.

In-line measurement and modeling of temperature, pressure, and blowing agent dependent viscosity of polymer melts

Evaluation of LLDPE/LDPE Blend Foamability by in Situ Rheological Measurements and Bubble Growth Simulations

Effects of Injection Molding Process Parameters on the Chemical Foaming Behavior of Polypropylene and Polystyrene

Analysis of Bubble Coalescence and Determination of the Bubble Radius for Long‐chain Branched Poly(ethylene Terephthalate) Melt Foaming with a Pressure Balanced Bubble‐growth Model

Study on the Flow, Foaming Characteristics and Structural Strength of Polypropylene Structural Foam Injection Molding by Innovative Nitrogen and Molten Plastic Mixing Mechanism

A Novel In-Line Measurement and Analysis Method of Bubble Growth-Dependent Strain and Deformation Rates during Foaming

Effect of Viscoelasticity on the Foaming Behaviour of Long-Chain Branched Polypropylene with Different Branching Degrees Analysed by Using Bubble-Growth Modelling

Experimental and Numerical Study of the Polyurethane Foaming Process Using High-Pressure CO2

Manipulation of Polymer Foam Structure Based on Co2-Induced Changes in Polymer Fundamental Properties

Dimensional Stability of LDPE Foams with CO2 + I-C4h10 Mixtures As Blowing Agent: Experimental and Numerical Simulation