Abstract:The role of proton irradiation in the general oxidation of 316L stainless steel in simulated PWR primary water after 1000 h immersion was clarified by comparing the microstructural and microchemical features of oxides formed on both the irradiated and un-irradiated regions of identical grains. Hence, the interference from differences in crystallographic orientation can be ruled out. Interestingly, the average inner oxide thickness on the irradiated region is significantly thinner than that on the un-irradiated region. The enhanced resistance to oxidation on the irradiated region originates from the more protective inner oxide layer and the formation of a continuous Ni-rich zone near the oxide/matrix interface. The inner oxide formed on irradiated region is less deficient in cation due to the enhanced diffusion of Cr from matrix by the irradiation-induced defects, thus making a better diffusion barrier. Meanwhile, the formation of continuous Ni-rich zone near the oxide/matrix interface, which is facilitated by the Ni-rich defects serving as nuclei, fast generation of vacancy at the interface and suppression of the outward diffusion of surplus Ni, can diminish the available space for the growth of inner oxide. The limited oxidation space and high Cr content at the oxide/matrix interface in the irradiated region result in the formation of rocksalt oxide while spinel oxide is formed near the interface in the un-irradiated region.

Oxidation of 316 Stainless Steel in Supercritical Water

Revealing the Effect of O2, SO2 and H2O in Supercritical CO2 on the Corrosion Behavior of 316L Steel at Elevated Temperature

CORROSION BEHAVIOR OF SUPER-AUSTENITIC STAINLESS STEEL AL-6XN IN SUPERCRITICAL WATER

Revealing the oxidation mechanism of 310S stainless steel in supercritical water via high-resolution characterization

Early corrosion properties of titanium alloys, Ni-based alloys and stainless steel in supercritical water oxidation of sewage sludge

Oxidation behavior of 316L austenitic stainless steel in high temperature air with long-term exposure

Clarifying the irradiation effect on the general oxidation of 316L stainless steel in high temperature hydrogenated water after 1000 h immersion

Effect of Long-Term Pre-oxidation on the Corrosion Rate of 316L Stainless Steel in a High-Temperature Water Environment

Corrosion behavior of nickel base alloys, stainless steel and titanium alloy in supercritical water containing chloride, phosphate and oxygen

Oxidation behavior of the directed energy deposited 316 L stainless steel in supercritical carbon dioxide environment: effect of post-manufacturing heat treatment

Investigation of Oxide Layer Development of X6CrNiNb18-10 Stainless Steel Exposed to High-Temperature Water

Understanding the surface oxide evolution of T91 ferritic-martensitic steel in supercritical water through advanced characterization

High-resolution characterization of the internal and external oxidation of austenitic alloys in supercritical water

Characterization of the oxide film formed on alumina-forming austenitic stainless steel in deaerated, DH, DO, and OT supercritical water

Effect of Exposure Temperature on Oxidation of Austenitic Steel HR3C in Supercritical Water

Comparison and mechanism research of corrosion behavior of materials used in supercritical water-cooled reactors

Corrosion Behavior of Si Diffusion Coating on an Austenitic Fe-Base Alloy in High Temperature Supercritical-Carbon Dioxide and Steam Environment

Corrosion of 316L stainless steel in high temperature water and steam: Mechanisms of corrosion

Impact of Water Vapor on the High Temperature Oxidation of Wrought and Selective Laser Melted (SLM) AISI 316L

Synergistic Effect of Solid State Hydrogen and Cold Work Pretreatment on Oxide Films Grown on 316L Stainless Steel during Short Term Immersion in Deaerated High Temperature Water at 300 °C

Corrosion characteristics of Fe, Ni and Ti based alloys near the critical point of water and during supercritical water gasification and oxidation of municipal sludge