Abstract:ABSTRACTThe cyclotrimerization of methylene diphenyl 4,4‐diisocyanate (MDI) and 3‐isopropenyl‐α,α′‐dimethylbenzene isocyanate (TMI) was applied on the bead/membrane surfaces of a polypropylene (PP)‐bearing isocyanate group to synthesize a protective networked polymer. Chemical structures of these molecules were characterized through attenuated total reflectance–Fourier transform infrared spectroscopy. Results showed that the absorption peak of isocyanate group at 2255 cm−1 became negligible after the reaction was completed. The absorption peaks of the isocyanurate groups appeared simultaneously at 1600 cm−1 and at 1510–1560 cm−1; this result indicated that the grafted isocyanates were almost consumed, thereby forming isocyanurates. Energy X‐ray dispersive spectroscopy revealed that oxygen content increased; indeed, isocyanurate was formed on the PP surface. Pure PP beads, PP‐g‐TMI, and cyclotrimerization products were also subjected to thermal property tests to investigate their corresponding thermal stabilities. Cyclotrimerization could result in the increase in PP‐grafted decomposition temperature, even slightly higher than pure PP. Rheological behavior in oscillatory flow was also evaluated; the storage modulus, loss modulus, and complex viscosity of cyclotrimerization products were higher than those of the PP‐grafted membranes. Surface morphology was further observed through field‐emission scanning electron microscopy and atomic force microscopy. The cyclotrimerization products contained blocks and exhibited a rough surface. © 2015 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2016, 133, 43327.

Influence of Different Peroxides on Structure and Properties of High Impact Polypropylene Prepared by Controlled-rheology Degradation

Investigation on the structure and crystallization behavior of controlled-rheology polypropylene with different stereo-defect distribution

The Effect of PP and Peroxide on the Properties and Morphology of HDPE and HDPE/PP Blends

Controlled properties of high-impact polypropylene in-reactor alloys by tailoring chemical structure and morphology

Rheology and Thermal Properties of Polypropylene Modified by Reactive Extrusion with Dicumyl Peroxide and Trimethylol Propane Triacrylate

Modification of Isotactic Polypropylene with Peroxide and Sulfur

Degradation Mechanism and Mechanical Properties Change of Isotactic Polypropylene in Processing

Evolution of Phase Morphology of High Impact Polypropylene Particles Upon Thermal Treatment

Structure and Properties of Reactive Extruded Ethylene-Block-Co-Polypropylene: Influence of Dicumyl Peroxide and Divinylbenzene

The Effects of Chemical Structure and Synthesis Method on Photodegradation of Polypropylene

Crystallization kinetics and morphology of high impact polypropylene

Influences of Dicumyl Peroxide on Morphology and Mechanical Properties of Polypropylene/poly(styrene‐b‐butadiene‐b‐styrene) Blends Via Vane‐extruder

Hierarchical structure and unique impact behavior of polypropylene/ ethylene-octene copolymer blends as obtained via dynamic packing injection molding

Preparation of High Molecular Weight Poly (P-Dioxanone) by Chain-Extension

The Effect of Tunable Modification Parameters on the Structure and Properties of Polypropylene with Cyclotrimerization Surface of Isocyanates

Probing into the Pristine Basic Morphology of High Impact Polypropylene Particles

Thermal and Crystallization Properties of HDPE and HDPE/PP Blends Modified with DCP

Investigation on Multifunctional Monomer Modified Polypropylene and Its Foamability

Crystalline structure, morphology and mechanical properties of β-nucleated controlled-rheology polypropylene random copolymers

PROPERTIES OF POLY(p-DIOXANONE-URETHANE) COPOLYMERS WITH CONTROLLABLE STRUCTURES

Preparation and Properties of High Modulus and High Impact Polypropylene Composites