Abstract:Statement of problem: Previous studies have shown casting methodology to influence the as-cast properties of dental casting alloys. It is important to consider clinically important mechanical properties so that the influence of casting can be clarified. Purpose: The purpose of this study was to evaluate how torch/centrifugal and inductively cast and vacuum-pressure casting machines may affect the castability, microhardness, chemical composition, and microstructure of 2 high noble, 1 noble, and 1 base metal dental casting alloys. Material and methods: Two commonly used methods for casting were selected for comparison: torch/centrifugal casting and inductively heated/ vacuum-pressure casting. One hundred and twenty castability patterns were fabricated and divided into 8 groups. Four groups were torch/centrifugally cast in Olympia (O), Jelenko O (JO), Genesis II (G), and Liberty (L) alloys. Similarly, 4 groups were cast in O, JO, G, and L by an inductively induction/vacuum-pressure casting machine. Each specimen was evaluated for casting completeness to determine a castability value, while porosity was determined by standard x-ray techniques. Each group was metallographically prepared for further evaluation that included chemical composition, Vickers microhardness, and grain analysis of microstructure. Two-way ANOVA was used to determine significant differences among the main effects. Statistically significant effects were examined further with the Tukey HSD procedure for multiple comparisons. Data obtained from the castability experiments were non-normal and the variances were unequal. They were analyzed statistically with the Kruskal-Wallis rank sum test. Significant results were further investigated statistically with the Steel-Dwass method for multiple comparisons (α=.05). Results: The alloy type had a significant effect on surface microhardness (P<.001). In contrast, the technique used for casting did not affect the microhardness of the test specimen (P=.465). Similarly, the interaction between the alloy and casting technique was not significant (P=.119). A high level of castability (98.5% on average) was achieved overall. The frequency of casting failures as a function of alloy type and casting method was determined. Failure was defined as a castability index score of <100%. Three of 28 possible comparisons between alloy and casting combinations were statistically significant. The results suggested that casting technique affects the castability index of alloys. Radiographic analysis detected large porosities in regions near the edge of the castability pattern and infrequently adjacent to noncast segments. All castings acquired traces of elements found in the casting crucibles. The grain size for each dental casting alloy was generally finer for specimens produced by the induction/vacuum-pressure method. The difference was substantial for JO and L. Conclusions: This study demonstrated a relation between casting techniques and some physical properties of metal ceramic casting alloys.

Study on Characters of Cast Zone of Cast Keeper

Characters of the Surface of the Cast-Bonded Keeper:An Experimental Study

A Comparison Between the Cast-Bonded Keeper with Different Dental Alloys in the Metallographic Structure

Effects of Normalizing and Tempering Temperature on Mechanical Properties and Microstructure of Low Alloy Wear Resistant Steel Casting

[A Study on Microstructures and Heat Reaction Zone of Laser-Melted and Cast Post-Keepers].

Corrosion behaviours of the dental magnetic keeper complexes made by different alloys and methods

Experimental study of squeeze casting of ZK60 magnesium alloy

Interactions between TiAl alloy and AZC/AMT binder systems in investment casting

Effect of burn-out temperature on magnetic keepers in cast noble metal alloy posts

Determination of casting parameters of thick wall die-casting of magnesium alloy and simulation of its processing

Interactions Between Ti Al Alloy and AZC/AMT Binder Systems in Investment Casting

Interactions Between TiAl and ZrO2 Face Coat During Centrifugal Investment Casting

Analysis of four dental alloys following torch/centrifugal and induction/ vacuum-pressure casting procedures

Mechanical Properties and Fracture Behaviors of a Non-heat-treated Alloy in Varied Regions Within a Megacasting

The Study of Microstructure and Mechanical Properties of High Strength and Toughness Casting Al-Cu Alloy

Study on Microstructure and Properties of Cast High-Boron Middle-carbon Wear-resistant Alloy

Accurate Simulation of Complex Temperature Field in Counter-Pressure Casting Process Using A356 Aluminum Alloy

Study on Squeeze Casting Shape Processing 、Microstructure and Properties of Retainer

Effect of Cooling Rate on Microstructure and Mechanical Properties of an Al-5.0Mg-3.0Zn-1.0Cu Cast Alloy

Production of ZL205A Alloy Shell Castings by Low Pressure Casting

Sinterability of Zirconia Top Coat of Investment Mold for Ti Alloy