Abstract:Background context: Facet joints have been discussed as influential factors in the development of lumbar degeneration, which includes disc herniation and degenerative lumbar spondylolisthesis. Facet orientation (FO) and facet tropism (FT) are two important structural parameters of the lumbar facet joints. Many previous studies have focused on single parameter analysis of the lumbar spine. Owing to the correlation between independent variables, single-factor analysis cannot reflect the interaction between variables; however, there has been no corresponding biomechanical method developed to address this problem. Purpose: To investigate the complex biomechanical influences on the lumbar spine when vertebral FO and FT are varied using finite element analysis (FEA) and contour maps visualization, and analyze the biomechanical role of facet joint structural parameters in the process of lumbar degenerative diseases. Study design: A biomechanical modelling, analysis, and verification study was performed. Methods: A three-dimensional non-linear FEA model of 3 denucleated intervertebral discs (L2-3, L3-4, L4-5) with adjacent vertebral bodies (L2-L5) was created. Previously performed in vitro experiments provided experimental data for the range of motion in each load direction that was used for calibration. For 12 lumbar models, different facet joint angles relative to the sagittal plane at both L3-4 facet joints were simulated for 35°≤FO≤50° and 0°≤FT≤15°. By modifying different values of FO and FT, FEA simulation of different lumbar spine models was performed. Contour maps were used to visualize the FO- and FT-relevant data. Results: Under flexion, extension, and torsion moments, facet joint contact force and intradiscal stress increased with increasing FT. In the condition where FT remained 0° and increasing FO values, facet joint contact force and intradiscal stress remained low with no apparent increasing or decreasing trend when the model was under flexion, extension, and torsion moments. In the condition where FO and the FT values were varied at the same time, the highest force and stress regions in the contour maps were observed when all three types of moments were applied. Stress distributions of the L3-4 disc with different FT and FO values showed disc stress increased significantly with increases of FT and was concentrated on the ipsilateral region of the facet joint with the more sagittal orientation. Conclusions: The combination of FO and FT has an important impact on the corresponding disc and facet joints, but FT played a more significant role. Moreover, disc stress was concentrated on the ipsilateral region of facet joint with greater sagittal orientation when FT existed. FT with high sagittal orientation may increase risk of recurrent LDH due to increase ipsilateral disc pressure. Clinical significance: These biomechanical findings may help clinicians to understand the prognosis of some lumbar degenerative conditions.

Stress Analysis of Facets after Cervical Laminectomy

Finite element analysis into the effect of discectomy on lumbar biomechanical characteristics

Influence of the Morphology of Lumbar Motion Segment on Isthmic Stress and Facet Contact Force: A Finite Element Analysisangzh

Finite Element Model Analysis of Lumbar Biomechanical Characteristics after Nucleus Discectomy

Determination of Contact Force at Facet Joint with Different Sagittal Orientation under Shearing Loads:A Finite Element Analysis

Topping-off surgery vs posterior lumbar interbody fusion for degenerative lumbar disease: a finite element analysis

The biomechanical influence of facet joint parameters on corresponding segment in the lumbar spine: a new visualization method

Using Finite Element Models to Assess Spinal Cord Biomechanics after Cervical Laminoplasty for Degenerative Cervical Myelopathy

Three-dimensional finite element modeling of whole lumbar spine and its biomechanical analysis

[Effects of Novel Angled Cervical Disc Replacement on Facet Joint Stress].

The Biomechanical Response of the Lower Cervical Spine Post Laminectomy: Geometrically-Parametric Patient-Specific Finite Element Analyses

FINITE ELEMENT ANALYSIS ON LUMBAR INTERBODY FUSION

A BIOMECHANICAL STUDY OF THE EFFECTS OF FLEXION ANGLE ON THE INDUCTION MECHANISM OF CERVICAL SPONDYLOSIS

Finite Element Based-Analysis for Pre and Post Lumbar Fusion of Adult Degenerative Scoliosis Patients

[Finite Element Analysis of Lumbar Fusion and Topping-off Surgery].

Distribution characteristics of stress on the vertebrae following different ranges of excision during Modified Anterior Cervical Discectomy and Fusion: A correlation study based on finite element analysis

Facet deflection and strain are dependent on axial compression and distraction in C5-C7 spinal segments under constrained flexion

Biomechanical Effects of Anterior Decompression and Fusion With Cervical Two-Segments Different Internal Fixation Systems: A Finite Element Study

Biomechanical response of decompression alone in lower grade lumbar degenerative spondylolisthesis--A finite element analysis

[Building an effective nonlinear three-dimensional finite-element model of human thoracolumbar spine]

Finite Element Analysis of Implanted Lumbar Spine: Effects of Open Laminectomy plus PLF and Open Laminectomy plus TLIF Surgical Approaches on L3-L4 FSU