Abstract:We aimed to investigate the corrosion patterns and the main controlling factors of N80 steel and P110 steel tubing under different sections. Conducting weight loss corrosion experiments for 168 h using high-temperature and high-pressure autoclaves to simulate the corrosion behavior of two types of casing materials, N80 steel and P110 steel, in different well sections under specific conditions of CO2 content, chloride ion concentration, temperature, pressure, and sulfate-reducing bacteria population in highly mineralized formation water. X-ray diffraction (XRD), scanning electron microscopy (SEM), and energy-dispersive X-ray spectroscopy (EDS) were used to analyze the corrosion products, surface morphology, and elemental composition of the two steel pipes. Additionally, 3D microscopy was employed to observe the morphology and measure the dimensions of localized corrosion pits. Under different well sections, the corrosion products formed on N80 steel and P110 steel mainly consist of FeCO3, and crystalline salts of chlorides present in the solution medium. Under low-water-cut conditions, narrow and deep corrosion defects were observed, while narrow and shallow corrosion defects were found under high-water-cut conditions. In the upper wellbore section, both steel pipes exhibited dispersed and thin corrosion product films that suffered from rupture and detachment, resulting in severe localized corrosion. In the middle wellbore section, the corrosion product film on N80 steel comprised irregularly arranged polygonal grains, some of which exhibited significant gaps, leading to extremely severe corrosion. For P110 steel, the corrosion product film was also dispersed and thin, with extensive detachment and extremely severe corrosion. In the lower wellbore section, both steel pipes were covered with a dense layer of grains, with smaller gaps between them, effectively protecting the metal matrix from corrosion. Consequently, the corrosion rate decreased compared to the middle section but still exhibited severe corrosion. In low-water-cut conditions, attention should be given to the risk of column safety due to corrosion from condensate water and CO2, as well as the size of narrow and deep corrosion defects in the middle wellbore section. In high-water-cut conditions, it is recommended to use corrosion inhibitors in combination while focusing on SRB bacteria corrosion in the upper wellbore section, condensate water in the middle section, CO2 content and chloride ion coupling in the lower section, and the size of narrow and shallow corrosion defects causing column safety risks.

Corrosion Resistance of Electroless Nickel-Phosphorous Coating on Drill-Pipe in Fresh-Water Mud

Corrosion Analysis of G105-Coated Drill-Pipe Washout and Electroless Plating Ni-P as Drill-Pipe Protection in Freshwater Mud

The Effect of Ni201 Transition Layer on the Corrosion, Wear and Synergetic Cavitation Erosion-Corrosion Behavior of CMT-Monel K500 Coating

Corrosion analysis of G105 coating drill-pipe washout

Time-dependent corrosion behavior of electroless Ni–P coating in H2S/Cl− environment

High Corrosion-Resistant Ni–P/Ni/Ni–P Multilayer Coatings on Steel

Progress in Research on Ni-Based Protective Coatings for Downhole Tubing Steel in CO2 Flooding

Effect of Heat Treatment and Passivation on Corrosion Behavior of Electroless Ni-P Coating on 20# Steel in Simulated Soil Solution

CHEMICAL PLATING MECHANISM IN ACID BATHS AND FABRICATION OF Ni-P COATING WITH HIGH P CONTENT

Tribological Behavior and Surface Analysis of Ni–P/BP Coatings

Enhancing Wear and Corrosion Resistance of Electroless Ni-P Coatings in CO 2 -saturated NaCl Solution through Polytetrafluoroethylene Incorporation

Effect of pre−corrosion on Electrochemical Corrosion and Fatigue Behavior of S135 High−Strength Drill Pipe Steel in Marine Environment

Preparation and Tribological Properties of the Carbon Nanotubes–ni–p Composite Coating

Effect of electroless deposition on the corrosion resistance property for NdFeB permanent magnets with surface coating of Ni-P alloy

Corrosion and Wear Behavior of WC–10Co4Cr Coating under Saturated Salt Drilling Fluid

Realization of Graphene on the Surface of Electroless Ni–P Coating for Short-Term Corrosion Prevention

Corrosion Behavior and Mechanical Performance of Drill Pipe Steel in a CO2/H2S-Drilling-Fluid Environment

Corrosion behaviors of arc spraying single and double layer coatings in simulated Dagang soil solution

Ni-Ce-P Electroless Plating and Properties of the Coating on 27simn Steel

Research on the Multifactor Synergistic Corrosion of N80 and P110 Steel Tubing in Shale Gas Wells in Sichuan Basin

Ni/Co/black phosphorus nanocomposites for Q235 carbon steel corrosion-resistant coating