Abstract:The thermal and dimensional stability of epoxy resin(EP)in-situ modified by cyanate ester(CE)and polydimethylsiloxane (PDMS) are investigated by means of experiments and numerical simulation. Thermal gravimetric analysis(TGA)and differential scanning calorimeter(DSC)are used to analyze the heat resistance of the modified EP. The dimensional stability is characterized by the volume shrinkage of the series PDMS/CE/EP obtained by the density method. The chemical structure of the PDMS/CE/EP is analyzed by Fourier transform infrared spectroscopy(FTIR). The results of TGA and DSC indicate that the thermal stability of PDMS/CE/EP decreases firstly and then increases with the increase in the amount of CE. The addition of PDMS shows a slight effect on the thermal stability. The 40％ CE makes the blending system exhibit the lowest initial decomposition temperature,which reduces by 15.5％ and 40.8％ compared with pure EP and CE,respectively. The FTIR results suggested that the influence of CE on the thermal stability of the modified EP is mainly ascribed to the generation of oxazolidinone ring with low thermal stability and the increase in the triazine ring with high thermal stability. The volume shrinkage measurement results show that the introduction of CE and PDMS are both beneficial to the improvement of the dimensional stability of the blending systems. The in-situ addition of 80％ CE shows the lowest volume shrinkage of 6.11％. The thermal stress distribution of PDMS/CE/EP generated during the solidification process is simulated by the finite element analysis. The results suggested that the introduction of 80％ CE into EP results in the lowest thermal stress in the blending system,which indicates that the system has the lowest volume shrinkage,which agrees well with the experimental results.

Modification and Flexible Film of CE

Cure of CE/EP/A System and Properties of the Film

Effects of Curing Conditions on Cure and Properties of Modified CE System

Modification of CE and Preparation of Flexible Film

Study on Co-curing Behavior and their Laminate Properties of Low Bromined Epoxy/Cyanate Blends

STUDY ON DGE-BHBTMBP/E-51/DDS CURED

Properties of epoxy terminated butadiene-acrylonitrile rubber modified cynate esters resin

Studies on Cure Kinetics of Diglycidyl Ether of 4,4′-Bisphenol/4,4′-diaminobiphenyl Using the Advanced Isoconversional Method

Influence of Cyanate Ester Modifier on the Thermal, Mechanical, and Corrosive Properties of Epoxy Composite Coating

Investigation on Mechanical Properties and Thermal Expansibility of Epoxy Resin Copolymerization Modified Cyanate Ester under Medium‐low Temperature Curing Process

Liquid Crystalline Epoxy Resin Modified Cyanate Ester/Epoxy Resin Systems

Curing kinetics and mechanical properties of cyanate ester/hyperbranched benzoxazine copolymers

THE TOUGHENING MODIFICATION OF CYANATE ESTERS RESIN MODIFIED BY EPOXY TERMINATED BUTADIENE-ACRYLONITRILE

Curing behavior and thermal performance of cyanate ester resin modified by Poly(methyl-benzene diethynylbenzene)Siliane

Study of E-51 Epoxy Resin Modified Bisphenol A Cyanate Ester Resins

A study on properties of epoxy resin toughened by functionalized polymer containing rigid, rod-like moiety

Properties of Copolymer Modification of Epoxy Resin／Bismaleimide Resin／Cyanate Ester Resin

Copolymerization of phthalonitrile-based resin containing benzoxazine and cyanate ester: Curing behaviors, fiber-reinforced composite laminates and improved properties

Investigation on Thermal and Dimensional Stability of Epoxy Resin In-Situ Modified by Cyanate Ester Resin and Polydimethylsiloxane

A novel biobased resin-epoxidized soybean oil modified cyanate ester

Toughness modification of cationic UV-cured cycloaliphatic epoxy resin by hydroxyl polymers with different structures