Abstract:Bisphenol A dicyanate (BADCy) resin microparticles were prepared by precipitation polymerization synthesis and were homogeneously dispersed in a BADCy prepolymer matrix to prepare a BADCy self-reinforced composites. The active functional groups of the BADCy resin microparticles were characterized by Fourier transform infrared (FT-IR) spectroscopy. The results of an FT-IR curve showed that the BADCy resin microparticles had a triazine ring functional group and also had an active reactive group -OCN, which can initiate a reaction with the matrix. The structure of the BADCy resin microparticles was characterized by scanning electron microscopy (SEM) and transmission electron microscopy (TEM). From the TEM results, the BADCy resin microparticles dispersed in the solvent were nano-sized and distributed at 40-60 nm. However, from the SEM results, agglomeration occurred after drying, the BADCy resin particels were micron-sized and distributed between 0.3 μm and 0.6 μm. The BADCy resin prepolymer was synthesized in our laboratory. A BADCy self-reinforced composite was prepared by using BADCy resin microparticles as a reinforcement phase. This corresponds to a composite in which the matrix and reinforcement phase are made from different morphologies of the same monomer. The DSC curve showed that the heat flow of the microparticles is different from the matrix during the curing reaction, this means the cured materials should be a microscopic two-phase structure. The added BADCy resin microparticles as reaction sites induced the formation of a more complete and regular cured polymer structure, optimizing the cross-linked network as well as increasing the interplay between the BADCy resin microparticles and prepolymer matrix. Relative to the neat BADCy resin material, the tensile strength, flexural strength, compressive strength and impact strength increased by 98.1%, 40.2%, 27.4%, and 85.4%, respectively. A particle toughening mechanism can be used to explain the improvement of toughness. The reduction in the dielectric constant showed that the cross-linked network of the self-reinforced composite was more symmetrical and less polar than the neat resin material, which supports the enhanced mechanical properties of the self-reinforced composite. In addition, the thermal behavior of the self-reinforced composite was characterized by thermogravimetric analysis (TGA) and dynamic mechanical thermal analysis (DMTA). The results of DMTA also establishes a basis for enhancing mechanical properties of the self-reinforced composite.

Study of E-51 Epoxy Resin Modified Bisphenol A Cyanate Ester Resins

STUDY ON DGE-BHBTMBP/E-51/DDS CURED

Cure and thermal properties of cyanate ester resin containing naphthalene ring

Branched 1,6-Diaminohexane-derived Aliphatic Polyamine As Curing Agent for Epoxy: Isothermal Cure, Network Structure, and Mechanical Properties

Study on Co-curing Behavior and their Laminate Properties of Low Bromined Epoxy/Cyanate Blends

Studies on Cure Kinetics of Diglycidyl Ether of 4,4′-Bisphenol/4,4′-diaminobiphenyl Using the Advanced Isoconversional Method

Studies on the Phase Separation of Poly(Ether Imide)‐Modified Cyanate Ester Resin

Thermal properties of an epoxy cresol-formaldehyde novolac/diaminodiphenyl sulfone system modified by bismaleimide containing tetramethylbiphenyl and aromatic ether structures

Synthesis and Curing of a Novel Combined Liquid Crystalline Epoxy

Morphology and mechanical properties of poly(ether-imide)-modified polycyanurates

A Comparative Study of Epoxy Resin Cured with a Linear Diamine and a Branched Polyamine

MODICATION OF BISPHENOL A DICYANATE ESTER BY EPOXIDIZED HYDROXYL-TERMINATED POLYBUTADIENE

Toughening of bisphenol A and carboxyl-terminated butadiene-acrylonitrile to epoxy resin

Properties of epoxy terminated butadiene-acrylonitrile rubber modified cynate esters resin

Catalytic Effect of Poly(silicon-Containing Arylacetylene) with Terminal Acetylene on the Curing Reaction and Properties of a Bisphenol A Type Cyanate Ester

Preparation, dielectric and thermomechanical properties of a novel epoxy resin system cured at room temperature

Study on Cure Reaction of the Blends of Bismaleimide and Dicyanate Ester

Properties of Copolymer Modification of Epoxy Resin／Bismaleimide Resin／Cyanate Ester Resin

Investigation on the Curing and Thermal Properties of Epoxy/Amine/Phthalonitrile Blend

Investigation on Mechanical Properties and Thermal Expansibility of Epoxy Resin Copolymerization Modified Cyanate Ester under Medium‐low Temperature Curing Process

Study on the Relationships between Microscopic Cross-Linked Network Structure and Properties of Cyanate Ester Self-Reinforced Composites