Abstract:PURPOSE The clinical failures of zirconia dental restorations are often caused by extrinsic artifacts introduced by processing. The aim of this study was to investigate the micro-defects and residual stresses generated during the multistep process of zirconia dental restorations. MATERIALS AND METHODS Thermal spray granulated 3Y-TZP powders were dry pressed by two tools exhibiting distinctly different Young's moduli, cold isostatic pressed (CIP-ed), and pressure-less fully sintered. The green bodies pressed by a stiff tool were treated with different procedures: direct milling (green milling) followed by fully sintering; half-sintering and milling (raw milling) with or without fully sintering; and fully sintering followed by grinding. The fully sintered 3Y-TZP crowns were clinically adjusted using both a diamond bur and SiC bur, respectively. Phase composition and microstructure of the pressed, milled, and ground surfaces were studied by XRD and SEM. RESULTS Tetragonal phase was the main phase of all detected 3Y-TZP specimens. Excessive residual stresses introduced by raw milling and grinding were confirmed by a strained T (111) peak, monoclinic phase, and obviously changed I(002)t /I(200)t ratio. The residual stresses would form a compressive stress layer, while it was too shallow to inhibit crack propagation even for ground specimens. Large voids with high-coordination numbers were the common packing micro-defects. Once formed, they were barely healed by CIP-ing and sintering. A stiff pressing tool was confirmed to be useful for reducing the surface packing voids. Milling removed the surface voids, but was no help for the interior ones. Raw milling introduced more serious chippings, most originating from the existing packing voids, than green milling due to its brittle failure and was less recommended for production. Grinding dense 3Y-TZP caused surface grain refinement and much more severe micro-defects, especially when clinical adjustment was applied by diamond bur compared to SiC bur. CONCLUSIONS Micro-defects and residual stresses are introduced and accumulated through the entire production chain and determine the final microstructure of zirconia dental restorations. Several procedural improvements are offered and expected to reduce processing micro-defects.

[Effect of Compaction Pressure on the Properties of Dental Machinable Zirconia Ceramic].

[Influence of Compaction Pressure and Pre-Sintering Temperature on the Machinability of Zirconia Ceramic].

Effect of Agglomeration on Mechanical Properties of Porous Zirconia Fabricated by Partial Sintering

Effect of Sintering Temperature on Part Physical Properties of Zirconia Dental Ceramic

Effect Of Molding Pressure On Structural And Densification Behavior Of Microwave-Sintered Ceramic Tool Material

The Effect of a Carbon Additive on Compaction of Partially Stabilized Zirconia Powders upon Pressing and Sintering

EFFECT OF SINTERING TEMPERATURE ON MECHANICAL PROPERTIES OF MACHINABLE 3Y-TZP BLANKS FOR DENTAL ALL-CERAMIC SUBSTRUCTURES

Mechanical Properties of Machinable Zirconia Dental Composites

Effect Of Sintering Temperature On Structures And Properties Of High Quality Zirconia Ceramics Under Oscillatory Pressure

[Effect of Two-Step Sintering Method on Properties of Zirconia Ceramic].

Study on Sintering Property and Mechanical Property of Nano-powder TZ-3Y-E As Dental Materials

Preparation of Zirconia Ceramics by Spark Plasma Sintering Technique and Their Mechanical Properties

Influence of Sintering Temperatures on Material Properties and Corresponding Milling Machinability of Zirconia Ceramics

An Oscillatory Pressure Sintering of Zirconia Powder: Densification Trajectories and Mechanical Properties

Effect of high-speed sintering on the microstructure, mechanical properties and ageing resistance of stereolithographic additive-manufactured zirconia

Investigating the effect of solid loading on microstructure, mechanical properties, and translucency of highly translucent zirconia ceramics prepared via stereolithography-based additive manufacturing

Effect of Oscillatory Pressure on the Sintering Behavior of ZrO2 Ceramic

Effect of Chairside Rapid Sintering Process on Microstructure and Mechanical Properties of TZP Zirconia Ceramics

Mechanical Performance of Polymer-Infiltrated Zirconia Ceramics.

Effect of Multistep Processing Technique on the Formation of Micro-Defects and Residual Stresses in Zirconia Dental Restorations.

Effect of Sintering Temperature on Compressive Strength of Porous Yttria-Stabilized Zirconia Ceramics